National Instruments NI 9219 Bedienungsanleitung

GETTING STARTED GUIDE

NI 9219

4 AI, 100 S/s/ch Simultaneous, Universal

Measurements

This document explains how to connect to the NI 9219.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9219. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9219 only as described in this document.

Caution Do not operate the NI 9219 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

2| ni.com | NI 9219 Getting Started Guide

Hazardous Voltage This icon denotes a warning

advising you to take precautions to avoid electrical

shock.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the device, take the

following precautions. A hazardous voltage is a voltage greater

than 42.4 Vpk voltage or 60 VDC to earth ground.

Caution Ensure that hazardous voltage wiring is

performed only by qualified personnel adhering to local

electrical standards.

Caution Do not mix hazardous voltage circuits and

human-accessible circuits on the same module.

Caution Ensure that devices and circuits connected to

the module are properly insulated from human contact.

Caution When module terminals are hazardous

voltage LIVE (>42.4 Vpk/60 VDC), you must ensure

that devices and circuits connected to the module are

properly insulated from human contact. You must use

the NI 9972 connector backshell kit to ensure that the

terminals are not accessible.

NI 9219 Getting Started Guide | © National Instruments | 3

Safety Voltages

Connect only voltages that are within the following limits.

Channel-to-channel

Continuous 250 VAC, Measurement

Category II

Withstand 1,390 VAC, verified by a 5 s

dielectric withstand test

Channel-to-earth ground

Continuous 250 VAC, Measurement

Category II

Withstand 2,300 VAC, verified by a 5 s

dielectric withstand test

Zone 2 hazardous locations applications in Europe

Channel-to-channel

and channel-to-earth

ground

60 VDC, Measurement

Category I

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

4| ni.com | NI 9219 Getting Started Guide

referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

Caution If using in Division 2 or Zone 2 hazardous

locations applications, do not connect the NI 9219 to

signals or use for measurements within Measurement

Categories II, III, or IV.

Note Measurement Categories CAT I and CAT O are

equivalent. These test and measurement circuits are not

intended for direct connection to the MAINS building

installations of Measurement Categories CAT II,

CAT III, or CAT IV.

Measurement Category II is for measurements performed on

circuits directly connected to the electrical distribution system.

This category refers to local-level electrical distribution, such as

that provided by a standard wall outlet, for example, 115 V for

U.S. or 230 V for Europe.

NI 9219 Getting Started Guide | © National Instruments | 5

Caution Do not connect the NI 9219 to signals or use

for measurements within Measurement Categories III

or IV.

Safety Guidelines for Hazardous Locations

The NI 9219 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9219 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

6| ni.com | NI 9219 Getting Started Guide

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9219 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 07 ATEX 0626664X and is

IECEx UL 14.0089X certified. Each NI 9219 is marked II 3G

and is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9219

in Gas Group IIC hazardous locations, you must use the device in

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC

T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC/EN 60664-1.

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

NI 9219 Getting Started Guide | © National Instruments | 7

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

stated in the product specifications. These requirements and

limits provide reasonable protection against harmful interference

when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in industrial locations. However,

harmful interference may occur in some installations, when the

product is connected to a peripheral device or test object, or if the

product is used in residential or commercial areas. To minimize

interference with radio and television reception and prevent

unacceptable performance degradation, install and use this

product in strict accordance with the instructions in the product

documentation.

8| ni.com | NI 9219 Getting Started Guide

Furthermore, any changes or modifications to the product not

expressly approved by National Instruments could void your

authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance,

operate this product only with shielded cables and

accessories.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for

marine (shipboard) applications. To verify Lloyd’s Register

certification for a product, visit ni.com/certification and search

for the LR certificate, or look for the Lloyd’s Register mark on

the product.

Caution In order to meet the EMC requirements for

marine applications, install the product in a shielded

enclosure with shielded and/or filtered power and

input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes

and cables to ensure that the desired EMC performance

is attained.

NI 9219 Getting Started Guide | © National Instruments | 9

Preparing the Environment

Ensure that the environment in which you are using the NI 9219

meets the following specifications.

Operating temperature

(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 70 °C

Operating humidity

(IEC 60068-2-78)

10% RH to 90% RH,

noncondensing

Pollution Degree 2

Maximum altitude 2,000 m

Indoor use only.

Note Refer to the device datasheet on ni.com/manuals

for complete specifications.

10 | ni.com | NI 9219 Getting Started Guide

Andere Handbücher für NI 9219

Inhaltsverzeichnis

Andere National Instruments Messgerät Handbücher

National Instruments

National Instruments BNC-2810 Bedienungsanleitung

National Instruments

National Instruments 779640-01 Bedienungsanleitung

National Instruments

National Instruments PXIe-5630 Bedienungsanleitung

National Instruments

National Instruments USB-5683 Bedienungsanleitung

National Instruments

National Instruments PXIe-5774 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4138 Handbuch

National Instruments

National Instruments NI 6601 Bedienungsanleitung

National Instruments

National Instruments USB-5684 Bedienungsanleitung

National Instruments

National Instruments NI PXI-562X Bedienungsanleitung

National Instruments

National Instruments NI 9213 Bedienungsanleitung

National Instruments

National Instruments PXIe-5665 Bedienungsanleitung

National Instruments

National Instruments NI 9227 Handbuch

National Instruments

National Instruments NI 5102 Bedienungsanleitung

National Instruments

National Instruments PXIe-5665 Bedienungsanleitung

National Instruments

National Instruments NI 5102 Bedienungsanleitung

National Instruments

National Instruments RM-26999 Handbuch

National Instruments

National Instruments NI PXIe-5105 Bedienungsanleitung

National Instruments

National Instruments PXI-4130 Handbuch

National Instruments

National Instruments 9235 Bedienungsanleitung

National Instruments

National Instruments PXIe-5668 Bedienungsanleitung

National Instruments

National Instruments Module NI PXI-8250 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4137 Handbuch

National Instruments

National Instruments 446 Series Handbuch

National Instruments

National Instruments NI TB-2644 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung