National Instruments WSN-3226 Bedienungsanleitung

USER GUIDE AND SPECIFICATIONS

NI WSN-3226

NI Wireless Sensor Network 4-Channel, 20-Bit Voltage/RTD Node

This user guide describes how to use the NI WSN-3226 voltage/RTD node and lists its specifications.

Figure 1 shows the NI WSN system components.

Figure 1. NI WSN System Components

The NI WSN-3226 is a four-channel, low-power, wireless voltage/resistance device that works with

other NI WSN-32xx nodes and gateways to form a wireless sensor network. The NI WSN system

consists of one or more NI WSN gateways, up to 36 NI WSN-32xx nodes per gateway, and multiple PCs

or Programmable Automation Controllers (PACs) to receive and analyze the distributed sensor data. For

more information about PACs, visit ni.com.

When you connect the NI WSN gateway, you can use a separate host PC running Windows, or a PAC

running NI LabVIEW Real-Time, to display measurement results, status information, and to change the

NI WSN gateway and NI WSN-3226 device settings.

1 NI WSN-32xx Nodes

2 NI 9792 WSN Real-Time Gateway

3 NI WSN-9791 Ethernet Gateway

4 PC Running NI Software

NI WSN-3226 User Guide and Specifications 2 ni.com

Dimensions

Figure 2 shows the NI WSN-3226 device dimensions.

Figure 2. NI WSN-3226 Device Dimensions

Safety Guidelines

Operate the NI WSN-3226 device only as described in this user guide.

Hot Surface This icon denotes that the component may be hot. Touching this component may result

in bodily injury.

NI WSN Safety Information

The following section contains important safety information that you must follow when installing and

using NI WSN products.

Caution Do not operate the NI WSN product in a manner not specified in the user manual or

operating instructions. Product misuse can result in a hazard. You can compromise the safety

protection built into the product if the product is damaged in any way. If the product is damaged,

return it to National Instruments for repair.

Caution Do not substitute parts or modify the NI WSN product. Use the product only with the

devices, accessories, and cables specified in the installation instructions.

Caution Do not operate NI WSN products in an explosive atmosphere or where there may be

flammable gases or fumes.

124 mm

(4.88 in.)

86.4 mm

(3.40 in.)

42.4 mm

(1.67 in.) 50.8 mm

(2.00 in.)

25.40 mm

(1.00 in.)

55.9 mm

(2.20 in.)

235 mm

(9.25 in.)

©National Instruments Corporation 3 NI WSN-3226 User Guide and Specifications

Caution If you need to clean a NI WSN product, wipe it with a dry towel. The product must be

completely dry and free from contaminants before you return it to service.

Caution Operate the product indoors only at or below Pollution Degree 2. Pollution is foreign matter

in a solid, liquid, or gaseous state that can reduce dielectric strength or surface resistivity.

Caution You must insulate signal connections for the maximum voltage for which the NI WSN

product is rated. Do not exceed the maximum ratings for the product. Do not install wiring while the

product is live with electrical signals. Do not remove or add connector blocks when power is

connected to the NI WSN system. Avoid contact between your body and the connector block signal

wiring when hot-swapping devices.

Caution To comply with safety regulations, use only recommended batteries with this product.

Refer to the Battery Power section for the recommended battery types.

Safety Guidelines for Hazardous Locations

The NI WSN-3226 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous locations;

Class I, Zone 2, AEx nC IIC T4 and Ex nL IIC T4 hazardous locations; and nonhazardous locations

only. Follow these guidelines if you are installing the NI WSN-3226 in a potentially explosive

environment. Not following these guidelines may result in serious injury or death.

Caution Observe the battery manufacturers’ operating temperature ratings listed in the Battery

operating temperature range specification section.

Caution Do not disconnect the power supply wires and connectors from the device unless power has

been switched off.

Caution Do not install or remove the device unless power has been switched off.

Caution Substitution of components may impair suitability for Class I, Division 2.

Caution For Zone 2 applications, install the WSN system in an enclosure rated to at least IP 54 as

defined by IEC 60529 and EN 60529.

Special Conditions for Hazardous Locations Use in Europe

Caution The NI WSN-3226 has been evaluated as Ex nA nL IIC T4 equipment under DEMKO

Certificate No. 07 nA nL 0626664X. Each device is marked II 3G and is suitable for use in Zone 2

hazardous locations, in ambient temperatures of –40 °C ≤Ta ≤70 °C.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for electromagnetic

compatibility (EMC) as stated in the product specifications. These requirements and limits are designed

to provide reasonable protection against harmful interference when the product is operated in its

intended operational electromagnetic environment.

This product is intended for use in industrial locations. There is no guarantee that harmful interference

will not occur in a particular installation, when the product is connected to a test object, or if the product

is used in residential areas. To minimize the potential for the product to cause interference to radio and

television reception or to experience unacceptable performance degradation, install and use this product

in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

NI WSN-3226 User Guide and Specifications 4 ni.com

The following statements contain important EMC information needed before installing and using this

product:

Caution To ensure the specified EMC performance, product installation requires either special

considerations or user-installed, add-on devices. See the product installation instructions for further

information.

Caution To ensure the specified EMC performance, operate this product only with shielded cables

and accessories.

Caution To ensure the specified EMC performance, operate this product with a DGND terminal on

the I/O connector tied to earth ground or use the NI recommended external power supply

(NI part number 780703-01) or equivalent.

Caution The inputs/outputs of this product can be damaged if subjected to Electrostatic Discharge

(ESD). To prevent damage, industry-standard ESD prevention measures must be employed during

installation, maintenance, and operation.

Caution This product may become more sensitive to electromagnetic disturbances in the operational

environment when test leads are attached or when connected to a test object.

Related Documentation

Check ni.com/manuals for the most recent documentation. For a complete list of documentation

related to the NI WSN system, refer to ni.com/info and enter rdwsnrd.

In addition to this guide, the following documents may be useful when configuring your NI WSN

system:

• NI Wireless Sensor Network Getting Started Guide

• NI WSN-9791 Ethernet Gateway User Guide and Specifications

• NI 9792 WSN Real-Time Gateway User Guide and Specifications

•Configuring WSN in MAX, available from Start»All Programs»National Instruments»NI-WSN

•LabVIEW Help for WSN Devices, available in LabVIEW from Help»LV Help»

WSN Devices Help

•NI-WSN Readme, available on the software installation disc included with your gateway

Training Courses

If you need more help getting started developing an application with NI products, NI offers training

courses. To enroll in a course or obtain a detailed course outline, refer to ni.com/training.

Technical Support on the Web

For additional support, refer to ni.com/support or zone.ni.com.

Software Overview

Note Refer to the NI WSN Readme, available on the software installation disc included with your

gateway, for NI software application version support.

NI-WSN software includes NI Measurement & Automation Explorer (MAX) as well as server and

driver software for easy integration into application software packages. These software components

manage the low-level communications and hardware configurations, simplifying programmatic access

to I/O channels. The NI-WSN software is on the software installation disc included with your NI WSN

©National Instruments Corporation 5 NI WSN-3226 User Guide and Specifications

gateway device. The NI-WSN software is supported by Windows 7/Vista/XP and contains the following

components:

•NIMAX

• NI-WSN

You can download a current version of NI-WSN software from ni.com/support. Using your Web

browser, go to ni.com/support and select Drivers and Updates»Distributed I/O»Wireless Sensor

Networks, and then select the latest version of NI-WSN software. If you are using other software, refer

to the installation instructions that accompany your software.

What You Need to Get Started

To set up and use NI LabVIEW with the NI WSN-3226 device, you need the following:

•NIWSNgateway

• NI WSN-3226 device(s) with a 5–30 V power supply or four alkaline or lithium AA 1.5 V batteries

for each node. Refer to the Battery Power section for recommended battery types.

• Mounting hardware (DIN rail, panel-mount, or rack mount accessory)

• Ethernet cable/connection

• 1/8 in. flathead and number 2 Phillips screwdrivers

• NI-WSN software version 1.2 or later

• Host PC running Windows 7/Vista/XP or LabVIEW Real-Time

• NI LabVIEW 2010 (32-bit) or later

•(NI 9792 WSN Real-Time Gateway Only)—NI LabVIEW 2009 SP1 (32-bit) Real-Time Module or

later

• Related hardware and software documentation

Unpack the Device and Install the Antenna

Remove the device from the package and inspect the device. Contact NI if the device appears damaged.

Do not install a damaged device.

Caution The device is static sensitive. Always properly ground yourself and the equipment when

handling or connecting to the device.

To attach the antenna, align the antenna with the mount and screw it on, as shown in Figure 3.

Caution The antenna must be attached to the NI WSN device in order for the NI WSN device to

function correctly.

NI WSN-3226 User Guide and Specifications 6 ni.com

Figure 3. Attach the Antenna to the Device

Mounting the NI WSN-3226 Device

You can mount the NI WSN-3226 on a panel or on a 35 mm DIN rail. For kit accessory ordering

information, refer to the NI WSN product page accessory section at ni.com. Before using any of these

mounting methods, remove and save the serial number sticker located on the back of the NI WSN-3226

device for future use when configuring your device in software. For the NI WSN-3226 device

dimensions, refer to Figure 2.

Caution Your installation must allow 50.8 mm (2 in.) of clearance in front of devices for common

connector cabling, such as the 18-terminal detachable screw terminal connector.

Attaching the NI WSN-3282 DIN Rail (Optional)

You can mount the NI WSN-3226 on a standard 35 mm DIN rail using a NI WSN-3282 DIN rail clip,

NI part number 781074-01. Complete the following steps to mount the NI WSN-3226 on a DIN rail:

Caution Power off the device before mounting it to the DIN rail.

Note Use thread-forming screws to permanently affix the DIN rail clip to the device. Unscrewing

and reinstalling the thread-forming screws will produce a compromised connection between the DIN

rail clip and the device.

1. Fasten the DIN rail clip to the NI WSN-3226 using a number 2 Phillips screwdriver and the

four 8-32 ×5/16 in. thread-forming screws that shipped with the DIN rail clip(s). Figure 4 shows

how to fasten the DIN rail clip to the NI WSN-3226.

Caution Do not use screws longer than 5/16 in. to fasten the DIN rail clip to the NI WSN-3226.

NATIONAL

INSTRUMENTS

NATIONAL

INSTRUMENTS

©National Instruments Corporation 7 NI WSN-3226 User Guide and Specifications

Figure 4. NI WSN-3226 Device DIN Rail Installation

2. Insert one edge of the DIN rail into the deeper opening of the DIN rail clip, as shown in Figure 5.

Figure 5. DIN Rail Clip Installation

3. Press down firmly on the NI WSN-3226 to compress the spring until the clip locks into place on

the DIN rail.

1 DIN Rail Clip (Without Device) 2 DIN Rail

NI WSN-3226 User Guide and Specifications 8 ni.com

Using a Panel Mount Accessory

The NI WSN-3280/3281 panel mount accessories, part numbers 780999-01 and 781073-01, each

include a retention clip and knob and integrated strain relief for power and I/O wires. You can use the

NI WSN-3280 panel mount accessory to attach the NI WSN-3226 device to a panel or other flat

surface. The NI WSN-3281 panel mount accessory also includes a magnetic mount for attaching the

NI WSN-3226 device to metallic surfaces. Figure 6 shows the NI WSN-3226 panel mounting

dimensions.

Figure 6. NI WSN-3226 Device Panel Mount Dimensions

78.74 mm

(3.100 in.)

4.5 mm

(5× Ø.177 in.)

44.02 mm

(1.733 in.)

183.79 mm

(7.236 in.)

55.88 mm

(2.200 in.)

13.97 mm

(0.550 in.)

25.40 mm

(1.000 in.)

25.40 mm

(1.000 in.)

53.34 mm

(2.100 in.)

©National Instruments Corporation 9 NI WSN-3226 User Guide and Specifications

Figure 7. Panel Mount Accessory

Refer to Figure 7 while completing the following steps to mount the NI WSN-3226 on a panel:

1. (NI WSN-3280) Bolt or screw the panel mount accessory to a panel using five 8-32 or M4 screws.

(NI WSN-3281) Attach the panel mount accessory using the integrated magnet.

2. Slide the NI WSN-3226 device into the panel mount accessory as shown in Figure 7.

1 Retention Knob

2 Retention Clip

3 Mounting Hole

4 Integrated Mounting Pin

5 Power and I/O Strain Relief

NATIONAL

INSTRUMENTS

NI WSN-3226 User Guide and Specifications 10 ni.com

3. Slide the retention clip down and tighten the panel mount knob to secure the NI WSN-3226 device

as shown in Figure 8.

Figure 8. Slide Retention Clip Down and Tighten Panel Mount Knob

4. (Optional) Secure any I/O signal or power supply cabling to the panel mount accessory using a

zip-tie and the integrated strain relief slots.

NATIONAL

INSTRUMENTS

NATIONAL

INSTRUMENTS

Andere Handbücher für WSN-3226

Inhaltsverzeichnis

Andere National Instruments Netzwerk-Hardware Handbücher

National Instruments

National Instruments NI 447 Series Bedienungsanleitung

National Instruments

National Instruments NI WLS/ENET-9163 Bedienungsanleitung

National Instruments

National Instruments NI 9375 Bedienungsanleitung

National Instruments

National Instruments Fieldbus Bedienungsanleitung

National Instruments

National Instruments PXI-1000 Bedienungsanleitung

National Instruments

National Instruments USB Digitizers NI USB-5132 Bedienungsanleitung

National Instruments

National Instruments GPIB Series Bedienungsanleitung

National Instruments

National Instruments GPIB-100A Bedienungsanleitung

National Instruments

National Instruments DAQ SCXI-1161 Bedienungsanleitung

National Instruments

National Instruments SCXI-1120 Bedienungsanleitung

National Instruments

National Instruments ISM-7413 Bedienungsanleitung

National Instruments

National Instruments GPIB GPIB-ENET/100 Bedienungsanleitung

National Instruments

National Instruments AT-232/2 Bedienungsanleitung

National Instruments

National Instruments FIELDPOINT FP-1600 Bedienungsanleitung

National Instruments

National Instruments PXI PXITM -1000 Bedienungsanleitung

National Instruments

National Instruments PXI Terminal Block NI TB-2708 Bedienungsanleitung

National Instruments

National Instruments SC-2040 Bedienungsanleitung

National Instruments

National Instruments NI-9206 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-2000 Bedienungsanleitung

National Instruments

National Instruments SCXI-1163 Bedienungsanleitung

National Instruments

National Instruments SCXI-1121 Bedienungsanleitung

National Instruments

National Instruments GPIB-120A Bedienungsanleitung

National Instruments

National Instruments NI PXI-7831R Bedienungsanleitung

National Instruments

National Instruments NI-488.2 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung