NETGEAR CM1100 Bedienungsanleitung

Nighthawk Multi-Gig Speed

Cable Modem

User Manual

Model CM1100

August 2018

202-11884-01

350 E. Plumeria Drive

San Jose, CA 95134

USA

Support

Thank you for purchasing this NETGEAR product.

You can visit https://www.netgear.com/support/ to register your product, get help, access the latest downloads

and user manuals, and join our community.We recommend that you use only official NETGEAR support

resources.

Contact your Internet service provider for technical support.

Trademarks

©NETGEAR, Inc. NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non-NETGEAR

trademarks are used for reference purposes only.

Compliance and Conformity

For regulatory compliance information, visit https://www.netgear.com/about/regulatory/. See the regulatory

compliance document before connecting the power supply.

Nighthawk Multi-Gig Speed Cable Modem

Contents

Chapter 1 Hardware Setup

UnpackYour Cable Modem....................................................................................5

Front Panel and LEDs............................................................................................6

Rear Panel.............................................................................................................8

Label......................................................................................................................9

System Requirements............................................................................................9

Install and ActivateYour Cable Modem................................................................10

ConnectYour Cable Modem to a Computer....................................................10

Activate Your Internet Service.........................................................................11

Perform a Speed Test......................................................................................12

ConnectYour Cable Modem to a Router After Installation and Activation.......12

Chapter 2 ManageYour Network

Change the admin Password...............................................................................15

View Cable Modem Initialization..........................................................................16

View Cable Modem Status...................................................................................16

View and Clear Event Logs..................................................................................17

Specify the Cable Connection Starting Frequency..............................................17

Ethernet Port Aggregation...................................................................................18

Set Up Ethernet Port Aggregation...................................................................18

View the Ethernet Port Aggregation Status.....................................................18

Change the Ethernet Port Aggregation Configuration Mode...........................19

Reboot the Cable Modem....................................................................................19

Reset the Cable Modem to Factory Default Settings...........................................20

Use the Reset Button on the Back Panel.............................................................21

Use the Factory Reset Software Button...............................................................21

Chapter 3Troubleshooting

Use LEDs to Troubleshoot...................................................................................23

Cannot Log In to the Cable Modem.....................................................................24

Troubleshoot the Cable Internet Connection........................................................25

Chapter 4 Supplemental Information

Factory Settings...................................................................................................27

Technical Specifications.......................................................................................27

Hardware Setup

This chapter covers the following topics:

•UnpackYour Cable Modem

•Front Panel and LEDs

•Rear Panel

•Label

•System Requirements

•Install and ActivateYour Cable Modem

For more information about the topics covered in this manual, visit the support website at support.netgear.com.

An uninterruptible power supply (UPS) can be purchased separately for continued service

during power outages. For a list of supported UPS models, visit

netgear.com/support/product/CM1100.

Note

UnpackYour Cable Modem

Your package contains the following items.

Figure 1. Package contents

1. High Speed Cable Modem (Model CM1100)

2. Ethernet cable

3. Power adapter

Hardware Setup

Nighthawk Multi-Gig Speed Cable Modem

Front Panel and LEDs

The cable modem provides status LEDs on the front.

Figure 2. Front panel

You can use the LEDs to verify status and connections.The following table lists and describes each LED

on the cable modem.

Hardware Setup

Nighthawk Multi-Gig Speed Cable Modem

Table 1. LED descriptions

DescriptionIconLED

•Solid green. Power is supplied to the cable modem.

•Off. No power is supplied to the cable modem.

•Solid red.The cable modem is too warm and might overheat.For more

information about this condition, see Use LEDs to Troubleshoot on

page 23.

Power

•Solid amber. One downstream channel is locked.

•Solid green.Two or more downstream channels are locked.

•Blinking green. The cable modem is scanning for a downstream

channel.

•Off. No downstream channel is locked.

Downstream

•Solid amber. One upstream channel is locked.

•Solid green.Two or more upstream channels are locked.

•Blinking green.Thecablemodemis scanning foran upstream channel.

•Off. No upstream channel is locked.

Upstream

•Solid green.The cable modem is online.

•Blinking green.The cable modem is synchronizing with the cable

provider’s cable modem termination system (CMTS).

•Off.The cable modem is offline.

Internet

Hardware Setup

Nighthawk Multi-Gig Speed Cable Modem

Table 1. LED descriptions (Continued)

DescriptionIconLED

•Green. A powered-on device is connected to the LAN port at 1000

Mbps.

•Amber.A powered-on device is connected to the LAN port at 10 Mbps

or 100 Mbps.

•Off. No device is connected to the LAN port.

•Blinking green or amber.The LAN port is processing traffic.

LAN 1

•Green. A powered-on device is connected to the LAN port at 1000

Mbps.

•Amber.A powered-on device is connected to the LAN port at 10 Mbps

or 100 Mbps.

•Off. No device is connected to the LAN port.

•Blinking green or amber.The LAN port is processing traffic.

LAN 2

Rear Panel

The connections and button on the rear panel are shown in the following figure.

Hardware Setup

Nighthawk Multi-Gig Speed Cable Modem

Figure 3. Rear panel

Viewed from top to bottom, the back panel contains the following components:

•Reset button.Pressing the Reset button resets the cable modem.If the Reset button is pressed for

at least seven seconds, the Power LED blinks green and the cable modem returns to its factory settings.

•LAN 1 and 2 ports. For installation and activation, connect a computer to the LAN 1 port. After you

install the cable modem and activate your Internet service, you can disconnect the computer and connect

a router to this port.You can use the LAN 2 port to set up Ethernet port aggregation.For more information,

see Ethernet Port Aggregation on page 18.

•Coaxial cable port. Connect the cable port to a cable wall outlet.

•Power On/Off button.Press the Power On/Off button to provide power to the cable modem.

•DC power connector.Connect the power adapter that came in the product package to the DC power

connector.

Label

The cable modem label shows the login information, MAC address, and serial number.

Figure 4. Cable modem label

System Requirements

You need the following to install your cable modem:

•Compatible operating system:

-Windows 10

-Windows 8

-Windows 7

-Windows Vista

-Windows XP

-Windows 2000

Hardware Setup

Nighthawk Multi-Gig Speed Cable Modem

-Mac OS

-Other operating systems running a TCP/IP network

•Compatible web browser:

-Microsoft Internet Explorer 5.0 or later

-Firefox 2.0 or later

-Safari 1.4 or later

-Google Chrome 11.0 or later

•Cable broadband Internet service

Install and ActivateYour Cable Modem

The cable modem provides a connection between your cable Internet provider’s network and your computer,

router, or WiFi router.

ConnectYour Cable Modem to a Computer

After you install the cable modem and activate your Internet service, you can disconnect the computer and

connect a router to the cable modem.

Figure 5. Connect your cable modem to a computer

To connect your cable modem directly to a computer:

1. Turn off and disconnect existing modems and routers.

If you are replacing a modem that is currently connected in your home, unplug the modem and plug the

new cable modem into the same outlet.

2. Connect a coaxial cable.

Use a coaxial cable to connect the cable port on the cable modem to a cable wall outlet.Make sure that

the cable is tightly connected.

Hardware Setup

Nighthawk Multi-Gig Speed Cable Modem

Inhaltsverzeichnis

Andere NETGEAR Modem Handbücher

NETGEAR

NETGEAR XM128U Bedienungsanleitung

NETGEAR

NETGEAR CMD31T Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk CM2050V Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk D7000 Bedienungsanleitung

NETGEAR

NETGEAR DM602 - ADSL-Modem - 8 Mbps DSL Modem Bedienungsanleitung

NETGEAR

NETGEAR AC329U Bedienungsanleitung

NETGEAR

NETGEAR DGFV338 - ProSafe Wireless ADSL Modem VPN Firewall... Bedienungsanleitung

NETGEAR

NETGEAR DM111PSPv2 Bedienungsanleitung

NETGEAR

NETGEAR CGD24G Bedienungsanleitung

NETGEAR

NETGEAR FUSE Bedienungsanleitung

NETGEAR

NETGEAR ATT-340U Bedienungsanleitung

NETGEAR

NETGEAR LB2120 Series Bedienungsanleitung

NETGEAR

NETGEAR D3600 Bedienungsanleitung

NETGEAR

NETGEAR DM200 Bedienungsanleitung

NETGEAR

NETGEAR NIGHTHAWK CAX25 Bedienungsanleitung

NETGEAR

NETGEAR CG2003D Bedienungsanleitung

NETGEAR

NETGEAR DG834PN - RangeMax ADSL Modem Wireless... Bedienungsanleitung

NETGEAR

NETGEAR CM700 Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk C7100V Bedienungsanleitung

NETGEAR

NETGEAR DM111P - ADSL2+ Ethernet Modem Bedienungsanleitung

NETGEAR

NETGEAR CG814M Bedienungsanleitung

NETGEAR

NETGEAR LTE Bridge 1110 Series Bedienungsanleitung

NETGEAR

NETGEAR MBM621 - 3G HSDPA Ethernet Modem Bedienungsanleitung

NETGEAR

NETGEAR DM111PSPv2 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung