NETGEAR WAX214 Bedienungsanleitung

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

Logo are trademarks of NETGEAR, Inc. Any

non‑NETGEAR trademarks are used for reference

purposes only.

JULY 2021

NETGEAR INTERNATIONAL LTD

Floor 1, Building 3,

University Technology Centre

Curraheen Road, Cork,

T12EF21, Ireland

WiFi 6 AX1800 Dual Band PoE Access Point

Model WAX214

Installation Guide

Power up the WAX214 access point (AP) by connecting the LAN/PoE port to a PoE

switch that supplies 802.3af PoE power and 1 Gbps Ethernet speed.

The following gure shows the AP connected to a NETGEAR GS310TP switch.

Access Point Model WAX214

Mounting bracket with screw holes

for mounting to a solid ceiling or

15/16in. (23.8mm) T-bar.

Package contents

Two screws and

anchors for ceiling

or wallmounting

Note: As an option, you can power up your WAX214 by connecting it to a PoE or PoE+ switch.

Overview

Step 1. Connect the WAX214

15 GHz WLAN LED

22.4 GHz WLAN LED

3LAN LED

Power LED

5Reset button

LAN/PoE port

DC power connector

1234

WAX214

WA X214

Sample connections

Router Internet

PoE switch

WiFi clients

Power adapter

(varies by region)

When you power up your new WAX214, the management WiFi network (SSID)

becomes active. We recommend that you use a WiFi‑enabled computer to connect to

the management SSID for set up.

Note: For security reasons, the management SSID turns off when inactive for 15

minutes. If this happens during setup, press the Reset button for 20 seconds to reset

the device to default settings.

1. On your WiFi‑enabled computer (or other WiFi client device), open the software

utility that manages WiFi connections.

The utility scans for all WiFi networks in your area.

2. Find and select your WAX214’s management SSID.

The default name of the management SSID is printed on the WAX214’s label.

The SSID uses the format “WAX214XXXXXX‑CONFIG‑ONLY,” where XXXXXX is

customized to every device (based on the last six digits of the MAC address).

3. Enter the default password (network key) printed on the WAX214’s label.

Your WiFi‑enabled computer joins the WAX214’s management SSID.

Step 2. Join the management WiFi network

1. Launch a web browser and enter https://www.aplogin.net (which is the same as

https://192.168.0.100) in the address eld.

The login page for the setup process displays.

Your browser might display a security warning, which you can dismiss. For more

information, see https://kb.netgear.com/000062980/.

2. Set a new local device password and, for the main SSID (WiFi network 1, which is

the only SSID enabled by default), assign an SSID name and a WiFi passphrase.

We recommend that you write down the password and passphrase.

3. Accept NETGEAR’s terms and conditions.

4. Click the Apply button.

Your settings are saved.

5. Repeat Step 1 of these login steps to log in to the local browser UI using your new

local device password.

You can now view and manage the WAX214 conguration settings.

Step 3. Log in to the local browser UI

Before using your AP, we recommend that you update to the latest WAX214 rmware.

1. On your WiFi‑enabled computer, open the software utility that manages WiFi

connections.

The utility scans for all WiFi networks in your area.

2. Find and select your WAX214’s main SSID and type the WiFi passphrase.

You can now connect to the Internet.

Note: If you cannot connect to the Internet, see the user manual at

netgear.com/support/download for more information.

3. Visit netgear.com/support/download and enter the model number to see if new

rmware is available for your device.

If new rmware is available, download the rmware le to your computer.

4. Launch a web browser and enter https://192.168.0.100 in the address eld.

5. Under System Manager, select Firmware to view the current rmware version.

6. In the Firmware Upgrade section, click the Choose File button, and browse to the

rmware le on your computer.

7. Click the Upload button. The page displays the upgrade progress.

WARNING: To avoid corrupting the rmware, do not interrupt the upgrade. For

example, do not close the browser, click a link, or load a new page. Do not power

off the AP.

8. When the upgrade nishes, reconnect to the main SSID.

The login page displays.

Your WAX214 is now ready for use.

Step 4. Connect to the Internet and update the

rmware

This device must be professionally installed. It is the installer’s responsibility to follow

local country regulations including operations within legal frequency channels, output

power and DFS requirements. Vendor or Reseller or Distributor is not responsible for

illegal wireless operations. Please see Device’s Terms and Conditions for more details.

CAUTION: Terms of Use

During installation and setup, the AP’s LEDs can light in these colors:

Power Solid amber. The AP is powered on.

LAN Solid blue. The LAN port detects a link with a powered‑on

device.

Blinking blue. The LAN port is transmitting or receiving data.

2.4 GHz WLAN Solid blue. The 2.4 GHz radio is operating without clients.

Blinking blue. The 2.4 GHz radio is transmitting or receiving

data.

5 GHz WLAN Solid blue. The 5 GHz radio is operating without clients.

Blinking blue. The 5 GHz radio is transmitting or receiving data.

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

Logo are trademarks of NETGEAR, Inc. Any

non‑NETGEAR trademarks are used for reference

purposes only.

JULY 2021

NETGEAR INTERNATIONAL LTD

Floor 1, Building 3,

University Technology Centre

Curraheen Road, Cork,

T12EF21, Ireland

WiFi 6 AX1800 Dual Band PoE Access Point

Model WAX214

Installation Guide

Power up the WAX214 access point (AP) by connecting the LAN/PoE port to a PoE

switch that supplies 802.3af PoE power and 1 Gbps Ethernet speed.

The following gure shows the AP connected to a NETGEAR GS310TP switch.

Access Point Model WAX214

Mounting bracket with screw holes

for mounting to a solid ceiling or

15/16in. (23.8mm) T-bar.

Package contents

Two screws and

anchors for ceiling

or wallmounting

Note: As an option, you can power up your WAX214 by connecting it to a PoE or PoE+ switch.

Overview

Step 1. Connect the WAX214

15 GHz WLAN LED

22.4 GHz WLAN LED

3LAN LED

Power LED

5Reset button

LAN/PoE port

DC power connector

1234

WAX214

WA X214

Sample connections

Router Internet

PoE switch

WiFi clients

Power adapter

(varies by region)

When you power up your new WAX214, the management WiFi network (SSID)

becomes active. We recommend that you use a WiFi‑enabled computer to connect to

the management SSID for set up.

Note: For security reasons, the management SSID turns off when inactive for 15

minutes. If this happens during setup, press the Reset button for 20 seconds to reset

the device to default settings.

1. On your WiFi‑enabled computer (or other WiFi client device), open the software

utility that manages WiFi connections.

The utility scans for all WiFi networks in your area.

2. Find and select your WAX214’s management SSID.

The default name of the management SSID is printed on the WAX214’s label.

The SSID uses the format “WAX214XXXXXX‑CONFIG‑ONLY,” where XXXXXX is

customized to every device (based on the last six digits of the MAC address).

3. Enter the default password (network key) printed on the WAX214’s label.

Your WiFi‑enabled computer joins the WAX214’s management SSID.

Step 2. Join the management WiFi network

1. Launch a web browser and enter https://www.aplogin.net (which is the same as

https://192.168.0.100) in the address eld.

The login page for the setup process displays.

Your browser might display a security warning, which you can dismiss. For more

information, see https://kb.netgear.com/000062980/.

2. Set a new local device password and, for the main SSID (WiFi network 1, which is

the only SSID enabled by default), assign an SSID name and a WiFi passphrase.

We recommend that you write down the password and passphrase.

3. Accept NETGEAR’s terms and conditions.

4. Click the Apply button.

Your settings are saved.

5. Repeat Step 1 of these login steps to log in to the local browser UI using your new

local device password.

You can now view and manage the WAX214 conguration settings.

Step 3. Log in to the local browser UI

Before using your AP, we recommend that you update to the latest WAX214 rmware.

1. On your WiFi‑enabled computer, open the software utility that manages WiFi

connections.

The utility scans for all WiFi networks in your area.

2. Find and select your WAX214’s main SSID and type the WiFi passphrase.

You can now connect to the Internet.

Note: If you cannot connect to the Internet, see the user manual at

netgear.com/support/download for more information.

3. Visit netgear.com/support/download and enter the model number to see if new

rmware is available for your device.

If new rmware is available, download the rmware le to your computer.

4. Launch a web browser and enter https://192.168.0.100 in the address eld.

5. Under System Manager, select Firmware to view the current rmware version.

6. In the Firmware Upgrade section, click the Choose File button, and browse to the

rmware le on your computer.

7. Click the Upload button. The page displays the upgrade progress.

WARNING: To avoid corrupting the rmware, do not interrupt the upgrade. For

example, do not close the browser, click a link, or load a new page. Do not power

off the AP.

8. When the upgrade nishes, reconnect to the main SSID.

The login page displays.

Your WAX214 is now ready for use.

Step 4. Connect to the Internet and update the

rmware

This device must be professionally installed. It is the installer’s responsibility to follow

local country regulations including operations within legal frequency channels, output

power and DFS requirements. Vendor or Reseller or Distributor is not responsible for

illegal wireless operations. Please see Device’s Terms and Conditions for more details.

CAUTION: Terms of Use

During installation and setup, the AP’s LEDs can light in these colors:

Power Solid amber. The AP is powered on.

LAN Solid blue. The LAN port detects a link with a powered‑on

device.

Blinking blue. The LAN port is transmitting or receiving data.

2.4 GHz WLAN Solid blue. The 2.4 GHz radio is operating without clients.

Blinking blue. The 2.4 GHz radio is transmitting or receiving

data.

5 GHz WLAN Solid blue. The 5 GHz radio is operating without clients.

Blinking blue. The 5 GHz radio is transmitting or receiving data.

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

Logo are trademarks of NETGEAR, Inc. Any

non‑NETGEAR trademarks are used for reference

purposes only.

JULY 2021

NETGEAR INTERNATIONAL LTD

Floor 1, Building 3,

University Technology Centre

Curraheen Road, Cork,

T12EF21, Ireland

WiFi 6 AX1800 Dual Band PoE Access Point

Model WAX214

Installation Guide

Power up the WAX214 access point (AP) by connecting the LAN/PoE port to a PoE

switch that supplies 802.3af PoE power and 1 Gbps Ethernet speed.

The following gure shows the AP connected to a NETGEAR GS310TP switch.

Access Point Model WAX214

Mounting bracket with screw holes

for mounting to a solid ceiling or

15/16in. (23.8mm) T-bar.

Package contents

Two screws and

anchors for ceiling

or wallmounting

Note: As an option, you can power up your WAX214 by connecting it to a PoE or PoE+ switch.

Overview

Step 1. Connect the WAX214

15 GHz WLAN LED

22.4 GHz WLAN LED

3LAN LED

Power LED

5Reset button

LAN/PoE port

DC power connector

1234

WAX214

WA X214

Sample connections

Router Internet

PoE switch

WiFi clients

Power adapter

(varies by region)

When you power up your new WAX214, the management WiFi network (SSID)

becomes active. We recommend that you use a WiFi‑enabled computer to connect to

the management SSID for set up.

Note: For security reasons, the management SSID turns off when inactive for 15

minutes. If this happens during setup, press the Reset button for 20 seconds to reset

the device to default settings.

1. On your WiFi‑enabled computer (or other WiFi client device), open the software

utility that manages WiFi connections.

The utility scans for all WiFi networks in your area.

2. Find and select your WAX214’s management SSID.

The default name of the management SSID is printed on the WAX214’s label.

The SSID uses the format “WAX214XXXXXX‑CONFIG‑ONLY,” where XXXXXX is

customized to every device (based on the last six digits of the MAC address).

3. Enter the default password (network key) printed on the WAX214’s label.

Your WiFi‑enabled computer joins the WAX214’s management SSID.

Step 2. Join the management WiFi network

1. Launch a web browser and enter https://www.aplogin.net (which is the same as

https://192.168.0.100) in the address eld.

The login page for the setup process displays.

Your browser might display a security warning, which you can dismiss. For more

information, see https://kb.netgear.com/000062980/.

2. Set a new local device password and, for the main SSID (WiFi network 1, which is

the only SSID enabled by default), assign an SSID name and a WiFi passphrase.

We recommend that you write down the password and passphrase.

3. Accept NETGEAR’s terms and conditions.

4. Click the Apply button.

Your settings are saved.

5. Repeat Step 1 of these login steps to log in to the local browser UI using your new

local device password.

You can now view and manage the WAX214 conguration settings.

Step 3. Log in to the local browser UI

Before using your AP, we recommend that you update to the latest WAX214 rmware.

1. On your WiFi‑enabled computer, open the software utility that manages WiFi

connections.

The utility scans for all WiFi networks in your area.

2. Find and select your WAX214’s main SSID and type the WiFi passphrase.

You can now connect to the Internet.

Note: If you cannot connect to the Internet, see the user manual at

netgear.com/support/download for more information.

3. Visit netgear.com/support/download and enter the model number to see if new

rmware is available for your device.

If new rmware is available, download the rmware le to your computer.

4. Launch a web browser and enter https://192.168.0.100 in the address eld.

5. Under System Manager, select Firmware to view the current rmware version.

6. In the Firmware Upgrade section, click the Choose File button, and browse to the

rmware le on your computer.

7. Click the Upload button. The page displays the upgrade progress.

WARNING: To avoid corrupting the rmware, do not interrupt the upgrade. For

example, do not close the browser, click a link, or load a new page. Do not power

off the AP.

8. When the upgrade nishes, reconnect to the main SSID.

The login page displays.

Your WAX214 is now ready for use.

Step 4. Connect to the Internet and update the

rmware

This device must be professionally installed. It is the installer’s responsibility to follow

local country regulations including operations within legal frequency channels, output

power and DFS requirements. Vendor or Reseller or Distributor is not responsible for

illegal wireless operations. Please see Device’s Terms and Conditions for more details.

CAUTION: Terms of Use

During installation and setup, the AP’s LEDs can light in these colors:

Power Solid amber. The AP is powered on.

LAN Solid blue. The LAN port detects a link with a powered‑on

device.

Blinking blue. The LAN port is transmitting or receiving data.

2.4 GHz WLAN Solid blue. The 2.4 GHz radio is operating without clients.

Blinking blue. The 2.4 GHz radio is transmitting or receiving

data.

5 GHz WLAN Solid blue. The 5 GHz radio is operating without clients.

Blinking blue. The 5 GHz radio is transmitting or receiving data.

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

Logo are trademarks of NETGEAR, Inc. Any

non‑NETGEAR trademarks are used for reference

purposes only.

JULY 2021

NETGEAR INTERNATIONAL LTD

Floor 1, Building 3,

University Technology Centre

Curraheen Road, Cork,

T12EF21, Ireland

WiFi 6 AX1800 Dual Band PoE Access Point

Model WAX214

Installation Guide

Power up the WAX214 access point (AP) by connecting the LAN/PoE port to a PoE

switch that supplies 802.3af PoE power and 1 Gbps Ethernet speed.

The following gure shows the AP connected to a NETGEAR GS310TP switch.

Access Point Model WAX214

Mounting bracket with screw holes

for mounting to a solid ceiling or

15/16in. (23.8mm) T-bar.

Package contents

Two screws and

anchors for ceiling

or wallmounting

Note: As an option, you can power up your WAX214 by connecting it to a PoE or PoE+ switch.

Overview

Step 1. Connect the WAX214

15 GHz WLAN LED

22.4 GHz WLAN LED

3LAN LED

Power LED

5Reset button

LAN/PoE port

DC power connector

1234

WAX214

WA X214

Sample connections

Router Internet

PoE switch

WiFi clients

Power adapter

(varies by region)

When you power up your new WAX214, the management WiFi network (SSID)

becomes active. We recommend that you use a WiFi‑enabled computer to connect to

the management SSID for set up.

Note: For security reasons, the management SSID turns off when inactive for 15

minutes. If this happens during setup, press the Reset button for 20 seconds to reset

the device to default settings.

1. On your WiFi‑enabled computer (or other WiFi client device), open the software

utility that manages WiFi connections.

The utility scans for all WiFi networks in your area.

2. Find and select your WAX214’s management SSID.

The default name of the management SSID is printed on the WAX214’s label.

The SSID uses the format “WAX214XXXXXX‑CONFIG‑ONLY,” where XXXXXX is

customized to every device (based on the last six digits of the MAC address).

3. Enter the default password (network key) printed on the WAX214’s label.

Your WiFi‑enabled computer joins the WAX214’s management SSID.

Step 2. Join the management WiFi network

1. Launch a web browser and enter https://www.aplogin.net (which is the same as

https://192.168.0.100) in the address eld.

The login page for the setup process displays.

Your browser might display a security warning, which you can dismiss. For more

information, see https://kb.netgear.com/000062980/.

2. Set a new local device password and, for the main SSID (WiFi network 1, which is

the only SSID enabled by default), assign an SSID name and a WiFi passphrase.

We recommend that you write down the password and passphrase.

3. Accept NETGEAR’s terms and conditions.

4. Click the Apply button.

Your settings are saved.

5. Repeat Step 1 of these login steps to log in to the local browser UI using your new

local device password.

You can now view and manage the WAX214 conguration settings.

Step 3. Log in to the local browser UI

Before using your AP, we recommend that you update to the latest WAX214 rmware.

1. On your WiFi‑enabled computer, open the software utility that manages WiFi

connections.

The utility scans for all WiFi networks in your area.

2. Find and select your WAX214’s main SSID and type the WiFi passphrase.

You can now connect to the Internet.

Note: If you cannot connect to the Internet, see the user manual at

netgear.com/support/download for more information.

3. Visit netgear.com/support/download and enter the model number to see if new

rmware is available for your device.

If new rmware is available, download the rmware le to your computer.

4. Launch a web browser and enter https://192.168.0.100 in the address eld.

5. Under System Manager, select Firmware to view the current rmware version.

6. In the Firmware Upgrade section, click the Choose File button, and browse to the

rmware le on your computer.

7. Click the Upload button. The page displays the upgrade progress.

WARNING: To avoid corrupting the rmware, do not interrupt the upgrade. For

example, do not close the browser, click a link, or load a new page. Do not power

off the AP.

8. When the upgrade nishes, reconnect to the main SSID.

The login page displays.

Your WAX214 is now ready for use.

Step 4. Connect to the Internet and update the

rmware

This device must be professionally installed. It is the installer’s responsibility to follow

local country regulations including operations within legal frequency channels, output

power and DFS requirements. Vendor or Reseller or Distributor is not responsible for

illegal wireless operations. Please see Device’s Terms and Conditions for more details.

CAUTION: Terms of Use

During installation and setup, the AP’s LEDs can light in these colors:

Power Solid amber. The AP is powered on.

LAN Solid blue. The LAN port detects a link with a powered‑on

device.

Blinking blue. The LAN port is transmitting or receiving data.

2.4 GHz WLAN Solid blue. The 2.4 GHz radio is operating without clients.

Blinking blue. The 2.4 GHz radio is transmitting or receiving

data.

5 GHz WLAN Solid blue. The 5 GHz radio is operating without clients.

Blinking blue. The 5 GHz radio is transmitting or receiving data.

Visit netgear.com/support to get your questions answered and access the latest

downloads.

You can also check out our NETGEAR Community for helpful advice at

community.netgear.com.

Support and Community

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français

canadien à https://www.netgear.com/support/download/.

(If this product is sold in Canada, you can access this document in Canadian French at

https://www.netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of Conformity, visit

https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.

By using this device, you are agreeing to NETGEAR’s Terms and Conditions at

https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the

device to your place of purchase within your return period.

Do not use this device outdoors. The PoE source is intended for intra building

connection only.

Applicable to 6 GHz devices only: Only use the device indoors. The operation of 6

GHz devices is prohibited on oil platforms, cars, trains, boats, and aircraft, except that

operation of this device is permitted in large aircraft while ying above 10,000 feet.

Operation of transmitters in the 5.925‑7.125 GHz band is prohibited for control of or

communications with unmanned aircraft systems.

Regulatory and Legal

2. Line up the holes on the bottom of the AP with the screws in the wall and mount

the AP to the wall.

1. Mark the wall where you want to insert the

provided anchors and screws, which must be 3.875

in. (98.5 mm) apart, and insert the anchors and

screws.

Leave about 0.25 in. (6 mm) of each screw

protruding from the wall so that you can insert the

screws into the holes on the bottom of the AP.

3.875 in. (98.5 mm)

The bottom of the AP includes two holes that let you mount the AP on two screws

inserted in a wall.

You can mount the access point (AP) to a solid surface (a wall or a ceiling), or to a

ceiling with a 15/16 in. (23.8mm) T-bar, or you can install the AP freestanding on a at

surface.

We recommend that you use a at Ethernet cable so that the cable ts in the narrow

space between the AP and the surface on which it is mounted or placed.

Mounting options

Mount to a solid wall

1. Slide the 15/16in. (23.8mm) bracket between the guides on the bottom of the AP

until it locks in place.

The locking tab must be at the front of the AP.

2. Hold the AP upside down.

Note: If you can reach behind the T‑bar, hold the T‑bar with one hand and the AP

with your other hand.

3. Align the rectangular protruding part of the bracket with the T‑bar.

4. Hook the bracket onto one side of the T‑bar.

5. Hook the bracket onto the other side of the T‑bar until the bracket locks onto the

T‑bar.

Mount to a T-bar

1. Using the anchors and screws provided, attach the 15/16 in. (23.8mm) bracket

with the screw holes to the ceiling.

The rectangular protruding part of the bracket must be facing the ceiling.

2. Hold the AP upside down with the front of the AP facing the bracket.

Then, line up the guides on the bottom of the AP with the bracket.

3. Slide the AP into the bracket until it locks in place.

The locking tab must be at the front of the AP.

Note: To unlock the AP, push the locking tab toward the ceiling and slide the AP out

of the bracket.

Locking tabSide view

Mount to a solid ceiling

Visit netgear.com/support to get your questions answered and access the latest

downloads.

You can also check out our NETGEAR Community for helpful advice at

community.netgear.com.

Support and Community

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français

canadien à https://www.netgear.com/support/download/.

(If this product is sold in Canada, you can access this document in Canadian French at

https://www.netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of Conformity, visit

https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.

By using this device, you are agreeing to NETGEAR’s Terms and Conditions at

https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the

device to your place of purchase within your return period.

Do not use this device outdoors. The PoE source is intended for intra building

connection only.

Applicable to 6 GHz devices only: Only use the device indoors. The operation of 6

GHz devices is prohibited on oil platforms, cars, trains, boats, and aircraft, except that

operation of this device is permitted in large aircraft while ying above 10,000 feet.

Operation of transmitters in the 5.925‑7.125 GHz band is prohibited for control of or

communications with unmanned aircraft systems.

Regulatory and Legal

2. Line up the holes on the bottom of the AP with the screws in the wall and mount

the AP to the wall.

1. Mark the wall where you want to insert the

provided anchors and screws, which must be 3.875

in. (98.5 mm) apart, and insert the anchors and

screws.

Leave about 0.25 in. (6 mm) of each screw

protruding from the wall so that you can insert the

screws into the holes on the bottom of the AP.

3.875 in. (98.5 mm)

The bottom of the AP includes two holes that let you mount the AP on two screws

inserted in a wall.

You can mount the access point (AP) to a solid surface (a wall or a ceiling), or to a

ceiling with a 15/16 in. (23.8mm) T-bar, or you can install the AP freestanding on a at

surface.

We recommend that you use a at Ethernet cable so that the cable ts in the narrow

space between the AP and the surface on which it is mounted or placed.

Mounting options

Mount to a solid wall

1. Slide the 15/16in. (23.8mm) bracket between the guides on the bottom of the AP

until it locks in place.

The locking tab must be at the front of the AP.

2. Hold the AP upside down.

Note: If you can reach behind the T‑bar, hold the T‑bar with one hand and the AP

with your other hand.

3. Align the rectangular protruding part of the bracket with the T‑bar.

4. Hook the bracket onto one side of the T‑bar.

5. Hook the bracket onto the other side of the T‑bar until the bracket locks onto the

T‑bar.

Mount to a T-bar

1. Using the anchors and screws provided, attach the 15/16 in. (23.8mm) bracket

with the screw holes to the ceiling.

The rectangular protruding part of the bracket must be facing the ceiling.

2. Hold the AP upside down with the front of the AP facing the bracket.

Then, line up the guides on the bottom of the AP with the bracket.

3. Slide the AP into the bracket until it locks in place.

The locking tab must be at the front of the AP.

Note: To unlock the AP, push the locking tab toward the ceiling and slide the AP out

of the bracket.

Locking tabSide view

Mount to a solid ceiling

Visit netgear.com/support to get your questions answered and access the latest

downloads.

You can also check out our NETGEAR Community for helpful advice at

community.netgear.com.

Support and Community

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français

canadien à https://www.netgear.com/support/download/.

(If this product is sold in Canada, you can access this document in Canadian French at

https://www.netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of Conformity, visit

https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.

By using this device, you are agreeing to NETGEAR’s Terms and Conditions at

https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the

device to your place of purchase within your return period.

Do not use this device outdoors. The PoE source is intended for intra building

connection only.

Applicable to 6 GHz devices only: Only use the device indoors. The operation of 6

GHz devices is prohibited on oil platforms, cars, trains, boats, and aircraft, except that

operation of this device is permitted in large aircraft while ying above 10,000 feet.

Operation of transmitters in the 5.925‑7.125 GHz band is prohibited for control of or

communications with unmanned aircraft systems.

Regulatory and Legal

2. Line up the holes on the bottom of the AP with the screws in the wall and mount

the AP to the wall.

1. Mark the wall where you want to insert the

provided anchors and screws, which must be 3.875

in. (98.5 mm) apart, and insert the anchors and

screws.

Leave about 0.25 in. (6 mm) of each screw

protruding from the wall so that you can insert the

screws into the holes on the bottom of the AP.

3.875 in. (98.5 mm)

The bottom of the AP includes two holes that let you mount the AP on two screws

inserted in a wall.

You can mount the access point (AP) to a solid surface (a wall or a ceiling), or to a

ceiling with a 15/16 in. (23.8mm) T-bar, or you can install the AP freestanding on a at

surface.

We recommend that you use a at Ethernet cable so that the cable ts in the narrow

space between the AP and the surface on which it is mounted or placed.

Mounting options

Mount to a solid wall

1. Slide the 15/16in. (23.8mm) bracket between the guides on the bottom of the AP

until it locks in place.

The locking tab must be at the front of the AP.

2. Hold the AP upside down.

Note: If you can reach behind the T‑bar, hold the T‑bar with one hand and the AP

with your other hand.

3. Align the rectangular protruding part of the bracket with the T‑bar.

4. Hook the bracket onto one side of the T‑bar.

5. Hook the bracket onto the other side of the T‑bar until the bracket locks onto the

T‑bar.

Mount to a T-bar

1. Using the anchors and screws provided, attach the 15/16 in. (23.8mm) bracket

with the screw holes to the ceiling.

The rectangular protruding part of the bracket must be facing the ceiling.

2. Hold the AP upside down with the front of the AP facing the bracket.

Then, line up the guides on the bottom of the AP with the bracket.

3. Slide the AP into the bracket until it locks in place.

The locking tab must be at the front of the AP.

Note: To unlock the AP, push the locking tab toward the ceiling and slide the AP out

of the bracket.

Locking tabSide view

Mount to a solid ceiling

Visit netgear.com/support to get your questions answered and access the latest

downloads.

You can also check out our NETGEAR Community for helpful advice at

community.netgear.com.

Support and Community

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français

canadien à https://www.netgear.com/support/download/.

(If this product is sold in Canada, you can access this document in Canadian French at

https://www.netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of Conformity, visit

https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.

By using this device, you are agreeing to NETGEAR’s Terms and Conditions at

https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the

device to your place of purchase within your return period.

Do not use this device outdoors. The PoE source is intended for intra building

connection only.

Applicable to 6 GHz devices only: Only use the device indoors. The operation of 6

GHz devices is prohibited on oil platforms, cars, trains, boats, and aircraft, except that

operation of this device is permitted in large aircraft while ying above 10,000 feet.

Operation of transmitters in the 5.925‑7.125 GHz band is prohibited for control of or

communications with unmanned aircraft systems.

Regulatory and Legal

2. Line up the holes on the bottom of the AP with the screws in the wall and mount

the AP to the wall.

1. Mark the wall where you want to insert the

provided anchors and screws, which must be 3.875

in. (98.5 mm) apart, and insert the anchors and

screws.

Leave about 0.25 in. (6 mm) of each screw

protruding from the wall so that you can insert the

screws into the holes on the bottom of the AP.

3.875 in. (98.5 mm)

The bottom of the AP includes two holes that let you mount the AP on two screws

inserted in a wall.

You can mount the access point (AP) to a solid surface (a wall or a ceiling), or to a

ceiling with a 15/16 in. (23.8mm) T-bar, or you can install the AP freestanding on a at

surface.

We recommend that you use a at Ethernet cable so that the cable ts in the narrow

space between the AP and the surface on which it is mounted or placed.

Mounting options

Mount to a solid wall

1. Slide the 15/16in. (23.8mm) bracket between the guides on the bottom of the AP

until it locks in place.

The locking tab must be at the front of the AP.

2. Hold the AP upside down.

Note: If you can reach behind the T‑bar, hold the T‑bar with one hand and the AP

with your other hand.

3. Align the rectangular protruding part of the bracket with the T‑bar.

4. Hook the bracket onto one side of the T‑bar.

5. Hook the bracket onto the other side of the T‑bar until the bracket locks onto the

T‑bar.

Mount to a T-bar

1. Using the anchors and screws provided, attach the 15/16 in. (23.8mm) bracket

with the screw holes to the ceiling.

The rectangular protruding part of the bracket must be facing the ceiling.

2. Hold the AP upside down with the front of the AP facing the bracket.

Then, line up the guides on the bottom of the AP with the bracket.

3. Slide the AP into the bracket until it locks in place.

The locking tab must be at the front of the AP.

Note: To unlock the AP, push the locking tab toward the ceiling and slide the AP out

of the bracket.

Locking tabSide view

Mount to a solid ceiling

Andere Handbücher für WAX214

Inhaltsverzeichnis

Andere NETGEAR Drahtloser Zugangspunkt Handbücher

NETGEAR

NETGEAR XWN5001 Bedienungsanleitung

NETGEAR

NETGEAR WG103 ProSafe Bedienungsanleitung

NETGEAR

NETGEAR WN203 Bedienungsanleitung

NETGEAR

NETGEAR WAB102 - 802.11a+b Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WAG302 Bedienungsanleitung

NETGEAR

NETGEAR Powerline 500 XWN5001 Bedienungsanleitung

NETGEAR

NETGEAR WN802Tv1 - Wireless-N Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG302v2 - ProSafe 802.11g Wireless Access... Montageanleitung

NETGEAR

NETGEAR WG103 ProSafe Bedienungsanleitung

NETGEAR

NETGEAR WNDR4300-TN Bedienungsanleitung

NETGEAR

NETGEAR Orbi Pro Bedienungs- und Wartungsanleitung

NETGEAR

NETGEAR ProSafe Premium WNDAP660 Bedienungsanleitung

NETGEAR

NETGEAR WAX615 Bedienungsanleitung

NETGEAR

NETGEAR WE102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAC510 Bedienungsanleitung

NETGEAR

NETGEAR WAG102 - ProSafe Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WG302 - 802.11g ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WAC730 Bedienungsanleitung

NETGEAR

NETGEAR WAG302 - ProSafe Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR XWN5001 Bedienungsanleitung

NETGEAR

NETGEAR FUSE Technisches Datenblatt

NETGEAR

NETGEAR HE102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG602v3 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAC124 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung