NETGEAR WG302v1 - ProSafe 802.11g Wireless Access... Bedienungsanleitung

Installation Guide

Follow these quick steps to install your wireless

access point.

You can also consult the Install Assistant or the Reference Manual on the

ResourceCD for ProSafe Wireless Access Point.

1Set up the WG302 Access Point

Tip: Before mounting the WG302 in a high location, first set up and

test the WG302 to verify wireless network connectivity.

a. Unpack the box and verify the contents and attach the antennas.

b. Prepare a PC with an Ethernet adapter. If this PC is already part

of your network, record itsTCP/IP configuration settings.

Configure the PC with a static IP address of 192.168.0.210 and

255.255.255.0 for the Subnet Mask.

c. Connect an Ethernet cable from the WG302 to the PC (A).

d. Turn on your computer, connect the power adapter to the

WG302 and verify the following:

• The PWR power light goes on.

• The LAN light of the wireless access point is lit when

connected to a powered on PC.

2Configure LAN and Wireless Access

a. Configure the WG302 Ethernet port for LAN access.

• Connect to the WG302 by opening your browser and

entering http://192.168.0.228 in the address field.

• When prompted, enter admin for the user name and

password for the password, both in lower case letters.

• Click the IP Settings link and configure the IP Settings for

your network.

b. Configure the wireless interface for wireless access. See the online

help or “Understanding Basic Wireless Settings” section in the

Reference Manual for full instructions.

c. Test wireless connectivity using a PC with a wireless adapter

configured according to the wireless settings you just set in the

WG302, establish a wireless connection to the WG302.

Now that you have finished the setup steps, you are ready to deploy

the WG302 in your network. If needed, you can now reconfigure the

PC you used in step 1 back to its original TCP/IP settings.

3Deploy the WG302 Access Point

a. Disconnect the WG302 and position it where you will deploy it.

The best location is elevated, such as wall mounted or on the top

of a cubicle, at the center of your wireless coverage area, and

within line of sight of all the mobile devices.

b. Lift the antenna on either side so that they are vertical.

Note: Consult the antenna positioning and configuration infor-

mation in the Reference Manual on the Resource CD for ProSafe

Wireless Access Point.

c. Connect an Ethernet cable from your WG302 Access Point to a

LAN port on your router, switch, or hub.

d. Connect the power adapter to the wireless access point and plug

the power adapter in to a power outlet.The PWR, LAN, and

Wireless LAN lights should light up.

4Verify Wireless Connectivity

Using a computer with an 802.11g or 802.11b wireless adapter, verify

connectivity by using a browser such as Netscape®or Internet

Explorer to connect to the Internet, or check for file and printer

access on your network.

Note: If you cannot connect, see to Troubleshooting Tips in this

guide or the Reference Manual on the Resource CD for ProSafe Wireless

Access Point.

802.11g ProSafe™Wireless Access Point WG302

Rese t Console 9600,N,8,1Primary LAN/POE Secondary[email protected]

WG302 802.11g

ProSafe™Wireless

Access Point

WG302 install guideƒ.r2.qxd 11/19/03 9:44 AM Page 1

Troubleshooting Tips

If you have trouble setting up your WG302, check the tips below.

No lights are lit on the access point.

The access point has no power.

• Make sure the power cord is connected to the access point and

plugged in to a working power outlet or power strip.

• Make sure you are using the correct NETGEAR power adapter

supplied with your access point.

The Ethernet LAN light is not lit.

There is a hardware connection problem.

• Make sure the cable connectors are securely plugged in at the access

point and the network device (hub, switch, or router).

• Make sure the connected device is turned on.

The Wireless LAN activity light is not lit.

The access point’s antennas are not working.

• If the Wireless LAN activity light stays off, disconnect the adapter

from its power source and then plug it in again.

• Make sure the antennas are tightly connected to the WG302.

• Contact NETGEAR if the Wireless LAN light remains off.

I cannot configure the wireless access point from

a browser.

Check these items:

• The WG302 is properly installed, LAN connections are OK, and it is

powered on. Check that the LAN port LED is green to verify that the

Ethernet connection is OK.

• If you are using the NetBIOS name of the WG302 to connect,

ensure that your PC and the WG302 are on the same network seg-

ment or that there is a WINS server on your network.

• If your PC uses a Fixed (Static) IP address, ensure that it is using an

IP Address in the range of the WG302. The WG302 default IP

Address is 192.168.0.228 and the default Subnet Mask is

255.255.255.0. The WG302 default setting is for a static IP address.

If the network where you are connecting it is using DHCP, configure

it accordingly. See the Reference Manual on the Resource CD for

ProSafe Wireless Access Point for more details.

I cannot access the Internet or the LAN with a

wireless capable computer.

There is a configuration problem. Check these items:

• You may not have restarted the computer with the wireless adapter to

have TCP/IP changes take effect. Restart the computer.

• The computer with the wireless adapter may not have the correct

TCP/IP settings to communicate with the network. Restart the

computer and check that TCP/IP is set up properly for that network.

The usual setting for Windows on the Network Properties is set to

“Obtain an IP address automatically.”

• The access point’s default values may not work with your network.

Check the access point default configuration against the configuration

of other devices in your network.

• For full instructions on changing the access point’s default values,

see the Reference Manual on the Resource CD for ProSafe Wireless

Access Point.

*M-10178-01*

M-10178-01 November 2003

Technical Support

PLEASE REFER TOTHE SUPPORT INFORMATION CARD THAT

SHIPPED WITH YOUR PRODUCT.

By registering your product at www.NETGEAR.com/register, we can

provide you with faster expert technical support and timely notices of

product and software upgrades.

NETGEAR, INC.

Support Information

Phone: 1-888-NETGEAR (For US & Canada only) - 24 x7 phone support

See Support information card for other countries.

E-mail: [email protected] (24 x 7 online support)

www.NETGEAR.com

Attention: When you configure the wireless settings of the device please make sure to select

the correct country settings. Due to EU-law the country settings must be identical to the

country, where the device is operating (important due to non-harmonized frequencies in

the EU).

Connecting and Auto Uplink are trademarks or registered trademarks of Netgear, Inc. in the

United States and/or other countries. Microsoft and Windows are registered trademarks of

Microsoft Corporation in the United States and/or other countries. Other brand and

product names are trademarks or registered trademarks of their respective holders.

0678

WG302 install guideƒ.r2.qxd 11/19/03 9:44 AM Page 4

Andere Handbücher für WG302v1 - ProSafe 802.11g Wireless Access...

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NETGEAR Drahtloser Zugangspunkt Handbücher

NETGEAR

NETGEAR WNHDE111 Handbuch

NETGEAR

NETGEAR WNAP210 Bedienungsanleitung

NETGEAR

NETGEAR WNDR4300-TN Bedienungsanleitung

NETGEAR

NETGEAR WND930 Bedienungsanleitung

NETGEAR

NETGEAR Orbi RBE970B Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WNDAP330 Bedienungsanleitung

NETGEAR

NETGEAR ME103 - 802.11b ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR Orbi PRO SRS60 Bedienungsanleitung

NETGEAR

NETGEAR WAC505 Bedienungsanleitung

NETGEAR

NETGEAR WAG302 - ProSafe Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WAG102 - ProSafe Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE WNDAP380R Bedienungsanleitung

NETGEAR

NETGEAR WAC720 Bedienungsanleitung

NETGEAR

NETGEAR ProSafe Premium WNDAP620 Bedienungsanleitung

NETGEAR

NETGEAR WN802T-100NAS Bedienungsanleitung

NETGEAR

NETGEAR WN604 - Wireless-N 150 Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG602NA Bedienungsanleitung

NETGEAR

NETGEAR FUSE Technisches Datenblatt

NETGEAR

NETGEAR ProSafe Premium WNDAP660 Bedienungsanleitung

NETGEAR

NETGEAR WG302v1 - ProSafe 802.11g Wireless Access... Kurzanleitung

NETGEAR

NETGEAR WN802Tv1 - Wireless-N Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG302 - 802.11g ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WAC124 Bedienungsanleitung

NETGEAR

NETGEAR WAX630E Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung