NETGEAR WN802Tv2 - Wireless-N Access Point Bedienungsanleitung

)NSTALLATION'UIDE

NETGEAR Wireless-N Access Point WN802Tv2

Start Here

Follow these instructions to set up your wireless-N access point.You can also consult the

documentation links on the Resource CD or the NETGEAR knowledge base at

http://kbserver.netgear.com. Please consult the Resource CD or the Documentation link on

the user interface to access the Reference Manual for instructions on advanced

configuration options.

Estimated Completion Time: 20 minutes.

Tip: Before mounting the WN802Tv2 Wireless-N Access Point in a high location, first set

up and test the WN802Tv2 to verify wireless network connectivity.

First, Set Up the WN802Tv2

1. CONNECT THE WIRELESS-N ACCESS POINT TOYOUR COMPUTER

a. Unpack the box and verify the contents.

b. Prepare a computer with Internet access and an Ethernet adapter. If this computer

is already part of your network, record its TCP/IP configuration settings.

Configure the computer with a static IP address of 192.168.0.210 and

255.255.255.0 as the Subnet Mask.

c. Connect an Ethernet cable from the

WN802Tv2 to the PC.

d. Securely insert the other end of the cable

into the WN802Tv2 Ethernet port.

e. Connect the NETGEAR Switching

Power Supply from the wireless-N

access point to an AC power outlet.

Note: Only connect your wireless-N

access point using the switching power

supply provided with the WN802Tv2.

f. Check the lights on the front of the wireless-N access point:

•Power: The green power light should be

lit. If the power light is not lit, check the

connections and check to see if the power

outlet is controlled by a wall switch that is

turned off.

•Ethernet: The Ethernet (LAN) light

should be lit (amber for 10/100 Mbps and green

for 1000 Mbps) indicating that a connection

has been made. If not, make sure the Ethernet

cable is securely attached at both ends.

•WLAN: The blue wireless light should

be lit and blinking indicating that it is sending a

signal.

2. CONFIGURE LAN AND WIRELESS ACCESS

a. Configure the WN802Tv2 Ethernet port for LAN access.Connect to the

WN802Tv2 by opening your browser and entering http://192.168.0.233 in the

address field.

A login window will display.

b. When prompted, enter admin for the

user name and password for the

password, both in lower case letters.

The NETGEAR Wireless-N Access

Point WN802Tv2 user interface will

display.

c. Select Wireless Settings under the

Setup menu on the left navigation pane and configure your wireless interface for

wireless access.

d. Then select WEP/WPA Settings under Security and configure the level of data

encryption security for your network.

See the online help or the online Reference Manual for full instructions.

http://192.168.0.233

e. Finally, select Basic Settings under the Setup menu on the left navigation pane

and configure the IP Settings for your network.

Note: If you change the default subnet of the LAN IP address, you will be

disconnected from the WN802Tv2 Wireless-N Access Point user interface. To

reconnect, reconfigure your computer with a static IP address within the new

LAN IP subnet.

Tip: Before you deploy your wireless-N access point, reserve an IP address

(based on the WN802Tv2’s MAC address) on the DHCP server. That way, you

can configure the wireless-N access point with a static IP address which you can

always use to log in to make future configuration changes.

3. TEST WIRELESS CONNECTIVITY

Using a computer with a wireless adapter configured according to the wireless

settings you just set in the WN802Tv2, establish a wireless connection to the

WN802Tv2.

Deploy the WN802Tv2

Now that you have finished the setup steps, you are ready to deploy the WN802Tv2 in

your network. If needed, you can now reconfigure the PC you used in step 1 back to its

original TCP/IP settings.

Warning: To allow for proper ventilation, always install the unit vertically using the

included stand. Do not lay the unit flat.

1. Disconnect the WN802Tv2 from the computer and place it where you will deploy it.

The best location is elevated, such as wall mounted or on the top of a cubicle, at the

center of your wireless coverage area, and within line of sight of all the mobile

devices. The WN802Tv2 should be positioned vertically.

2. Connect an Ethernet cable from your WN802Tv2 wireless-N access point to a LAN

port on your router, switch, or hub.

3. Connect the power adapter to the wireless-N access point and plug the power adapter

in to a power outlet. The Power, WLAN and Ethernet lights should light up.

Note: A wall mount kit is included with theWN802Tv2. Instructions for installing the

brackets and mounting the WN802Tv2are in the online Reference Manual.

May 2008

This symbol was placed in accordance with the European Union Directive 2002/96 on the

Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the

European Union, this product should be treated and recycled in accordance with the laws of

your jurisdiction implementing the WEEE Directive.

or registered trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product

names are trademarks or registered trademarks of their respective holders. Information is subject to change with-

out notice.

Now, Verify Wireless Connectivity

Using a computer with an 802.11g, 802.11b or 802.11n wireless adapter, verify

connectivity by using a browser such as Netscape®, Internet Explorer or Mozilla

Firefox® to connect to the Internet, and check for file and printer access on your network.

Note: If you cannot connect, see the Troubleshooting Tips in this guide or the link to the

Reference Manual on the Resource CD.

Troubleshooting Tips

Here are some tips for correcting simple problems you may have.

No lights are lit on the access point.

The access point has no power.

• Make sure the Power Supply is connected to the access point and plugged in to a

working power outlet or power strip.

• Make sure you are using the Netgear Switching Power Supply supplied with your

access point.

The Ethernet light is not lit.

There is a hardware connection problem.

• Make sure the cable connectors are securely plugged in at the access point and the

network device (hub, switch, or router).

• Make sure the connected device is turned on.

The WLAN light is not lit.

The access point’s antennas are not working.

• If the Wireless LAN activity light stays off, disconnect the adapter from its power

source and then plug it in again.

• Contact NETGEAR if the WLAN light remains off.

I cannot configure the access point from a browser.

Check these items:

• The WN802Tv2 is properly installed and it is powered on. Check that the Ethernet

port LED is green to verify that the Ethernet connection is OK.

• If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address in the

range of the WN802Tv2. The WN802Tv2 default IP Address is 192.168.0.233 and

the default Subnet Mask is 255.255.255.0. The WN802Tv2 default setting is for a

static IP address. If the network where you are connecting it is using DHCP, configure

it accordingly. See the Reference Manual on the Resource CD for the Wireless Access

Point for more details.

Note: The factory default reset button and the default settings for your wireless-N

access point are located on the label at the rear of your WN802Tv2.

I cannot access the Internet or the LAN with a wireless capable

computer.

There is a configuration problem. Check these items:

• You may not have restarted the computer with the wireless adapter to have TCP/IP

changes take effect. Restart the computer.

• The computer with the wireless adapter may not have the correct TCP/IP settings to

communicate with the network. Restart the computer and check that TCP/IP is set up

properly for that network. The usual setting for Windows on the Network Properties

is set to “Obtain an IP address automatically.”

• The access point’s default values may not work with your network. Check the access

point default configuration against the configuration of other devices in your network.

• For full instructions on changing the access point’s default values, consult the

documentation links on the Resource CD or on the menu of the wireless-N access

point user interface.

Technical Support

Thank you for selecting NETGEAR products.

To register your product, go to: http://www.NETGEAR.com/register

Go to http://www.NETGEAR.com/support for support information.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NETGEAR Drahtloser Zugangspunkt Handbücher

NETGEAR

NETGEAR WG602v1 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR AirBridge WBC502 Handbuch

NETGEAR

NETGEAR EX7000 Bedienungsanleitung

NETGEAR

NETGEAR Orbi Pro Satellite Bedienungsanleitung

NETGEAR

NETGEAR WPN802 Bedienungsanleitung

NETGEAR

NETGEAR WG102 - ProSafe Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WN802Tv1 - Wireless-N Access Point Bedienungsanleitung

NETGEAR

NETGEAR HE102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WNAP320 Bedienungsanleitung

NETGEAR

NETGEAR WAC120 Bedienungsanleitung

NETGEAR

NETGEAR WG302v1 - ProSafe 802.11g Wireless Access... Kurzanleitung

NETGEAR

NETGEAR WG602v2 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WG102-500 Bedienungsanleitung

NETGEAR

NETGEAR WNDR4300-TN Bedienungsanleitung

NETGEAR

NETGEAR WG102 - ProSafe Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAX214 Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WG102-500 Bedienungsanleitung

NETGEAR

NETGEAR WAC510 Bedienungsanleitung

NETGEAR

NETGEAR WN802T Bedienungsanleitung

NETGEAR

NETGEAR ME103 - 802.11b ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WN203 Bedienungsanleitung

NETGEAR

NETGEAR WG302v2 - ProSafe 802.11g Wireless Access... Montageanleitung

NETGEAR

NETGEAR WG302 - 802.11g ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WAX214v2 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung