Netvox R718DB2 Bedienungsanleitung

Wireless 2-Gang Vibration Sensor, Spring Type

R718DB2

Wireless 2-Gang Vibration Sensor,

Spring Type

R718DB2

User Manual

This document contains proprietary technical information which is the property of NETVOX Technology. It shall

be maintained in strict confidence and shall not be disclosed to other parties, in whole or in part, without written

permission of NETVOX Technology. The specifications are subject to change without prior notice.

Table of Content

1. Introduction.......................................................................................................... 2

2. Appearance........................................................................................................... 3

3. Main Features ...................................................................................................... 3

4. Set up Instruction................................................................................................. 4

5. Data Report.......................................................................................................... 5

5.1 Example of ReportDataCmd.......................................................................... 6

5.2 Example of ConfigureCmd............................................................................ 7

5.3 Example for MinTime/MaxTime logic.......................................................... 8

6. Installation ........................................................................................................... 9

7. Information about Battery Passivation............................................................... 10

7.1 To determine whether a battery requires activation ..................................... 10

7.2 How to activate the battery .......................................................................... 10

8. Important Maintenance Instruction.................................................................... 11

1. Introduction

R718DB2 is a 2-way long-range wireless spring-loaded vibration device for Netvox ClassA-type devices based on the

LoRaWAN open protocol and is compatible with the LoRaWAN protocol.

LoRa Wireless Technology:

LoRa is a wireless communication technology dedicated to long distance and low power consumption. Compared with other

communication methods, LoRa spread spectrum modulation method greatly increases to expand the communication distance.

Widely used in long-distance, low-data wireless communications. For example, automatic meter reading, building automation

equipment, wireless security systems, industrial monitoring. Main features include small size, low power consumption,

transmission distance, anti-interference ability and so on.

LoRaWAN:

LoRaWAN uses LoRa technology to define end-to-end standard specifications to ensure interoperability between devices and

gateways from different manufacturers.

2. Appearance

3. Main Features

Adopt SX1276 wireless communication module.

2 x 3.6V ER14505 AA size lithium batteries

Trigger the vibration sensor, the device will send trigger information.

The base is equipped with a magnet that can be attached to the magnetic substance.

IP Ratings: Main part- IP65/IP67 (Optional), Sensor-/IP67

Compatible with LoRaWAN TM Class A

Frequency hopping spread spectrum technology

Configuration parameters can be configured through third-party software platforms.

Applicable to third-party platforms:Actility / ThingPark, TTN, MyDevices / Cayenne

Low power consumption and long battery life

Note:

Battery life is determined by the sensor reporting frequency and other variables.

Please refer to http://www.netvox.com.tw/electric/electric_calc.html

On this website, users can find various types of battery lifetime in different configurations.

Indicator

Function Key

Vibration Sensor

4. Set up Instruction

On/Off

Power on Insert batteries (Users may need a screwdriver to open)

Turn on Press and hold the function key for 3 seconds and the green indicator flash once.

Turn off (Restore to factory setting) Press and hold the function key for 5 seconds and the green indicator flashes 20 times.

Power off Remove Batteries.

Note:

1. Remove and insert the battery; the device is at off state by default.

2. On/off interval is suggested to be about 10 seconds to avoid the interference of

capacitor inductance and other energy storage components.

3. For the first 5 second after powering on, the device will be in engineering test mode.

Network Joining

Never joined the network

Turn on the device to search the network to join.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Had joined the network

Turn on the device to search the previous network to join.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Fail to join the network

(when the device is on)

Suggest to check the device verification information on the gateway or consult your

platform server provider.

Function Key

Press and hold for 5 seconds

Restore to factory setting / Turn off

The green indicator flashes 20 times: success

The green indicator remains off: fail

Press once The device is in the network: the green indicator flashes once and sends a report

The device is not in the network: the green indicator remains off

Sleeping Mode

The device is on and in the network

Sleeping period: Min Interval.

When the reportchange exceeds setting value or the state changes: send a data report

according to Min Interval.

Low Voltage Warning

Low Voltage

3.2V

5. Data Report

Data report configuration and sending period are as following:

Min Interval

(Unit:second)

Max Interval

(Unit:second) Reportable Change Current Change≥

Reportable Change

Current Change＜

Reportable Change

Any number between

1~65535

Any number between

1~65535 Can not be 0. Report

per Min Interval

Report

per Max Interval

The device will immediately send a version packet report and the vibration report data.

The device sends data in the default configuration before any configuration is done.

Default setting:

Max Interval: 0x0E10 (3600s)

Min Interval: 0x0E10 (3600s)

BatteryVoltageChange: 0x01 (0.1V)

R718DB2 Trigger:

When the sensor senses the vibration and the spring deforms, an alarm message will be reported.

The vibration is “1”.

No vibration is “0”.

The vibration Restore Configuration

The Restore function is used to send the final static status of the device.

(Please refer to the configuration command format below.)

Restore = 0, no data will be sent when the device is rest.

The data is sent with the next report.

Restore = 1, the data will be sent with a vibration bit-- 0 after the device is rest for 5 seconds.

Note:

1. The function of Restore is supported by the firmware version after 2020/05/18 version.

2. The device report interval will be programmed based on the default firmware which may vary.

3. The interval between two reports must be the minimum time.

Please refer Netvox LoRaWANApplication Command document and Netvox Lora Command Resolver

http://cmddoc.netvoxcloud.com/cmddoc to resolve uplink data.

5.1 Example of ReportDataCmd

FPort：0x06

Bytes 1 1 1 Var (Fix=8 Bytes)

Version DeviceType ReportType NetvoxPayLoadData

Version– 1 byte –0x01——the Version of NetvoxLoRaWAN Application Command Version

DeviceType– 1 byte – Device Type of Device

The devicetype is listed in Netvox LoRaWAN Application Devicetype doc

ReportType – 1 byte –the presentation of the NetvoxPayLoadData，according the devicetype

NetvoxPayLoadData– Fixed bytes (Fixed =8bytes)

Device Device

Type

Report

Type NetvoxPayLoadData

R718DB2 0x3D

0x00 SoftwareVersion

(1Byte)Eg.0x0A—V1.0

HardwareVersion

(1Byte)

DateCode

(4Bytes,eg 0x20170503)

Reserved

(2Bytes,fixed 0x00)

0x01 Battery

(1Byte, unit:0.1V)

Status 1

(1Byte 0:off 1:on)

Status 2

(1Byte 0:off 1:on)

Reserved

(5Bytes,fixed 0x00)

Example 1 of Uplink: 013D012401000000000000

1st byte (01): Version

2nd byte (3D): DeviceType 0x3D －R718DB2

3rd byte (01): ReportType

4th byte (24): Battery －3.6V, 24(Hex) = 36(Dec), 36x0.1v=3.6v

5th byte (01): Status －on

6th byte (00): Status －off

7th -11th byte (0000000000): Reserved

Tips

1. Battery Voltage:

The voltage value is bit 0 ~ bit 6, bit 7=0 is normal voltage, and bit 7=1 is low voltage.

Battery=0xA0, binary=1010 0000, if bit 7= 1, it means low voltage.

The actual voltage is 0010 0000 = 0x20 = 32, 32*0.1v =3.2v

2. Version Packet:

When Report Type=0x00 is the version packet, such as 013D000A0B202005200000, the firmware version is 2020.05.20

3. Data Packet:

When Report Type=0x01 is data packet.

Example 2 of Uplink: 013D01A000010000000000

1st byte (01): Version

2nd byte (3D): DeviceType 0x3D －R718DB2

3rd byte (01): ReportType

4th byte (A0): Battery －3.2V, 20(HEX)=32(DEC),32*0.1v=3.2v // Low battery

5th byte (00): Status －off

6th byte (01): Status －on

7th -11th byte (0000000000): Reserved

5.2 Example of ConfigureCmd

FPort：0x07

Bytes 1 1 Var (Fix =9 Bytes)

CmdID DeviceType NetvoxPayLoadData

CmdID– 1 byte

DeviceType– 1 byte – Device Type of Device

NetvoxPayLoadData– var bytes (Max=9bytes)

（1）Command Configuration:

MinTime = 1min、MaxTime = 1min、BatteryChange = 0.1v

Downlink：013D003C003C0100000000 003C (Hex) = 60 (Dec)

Response：

813D000000000000000000（Configuration success）

813D010000000000000000（Configuration failure）

Description Device CmdID Device

Type NetvoxPayLoadData

Config

ReportReq

R718DB2

0x01

0x3D

MinTime

(2bytes Unit:s)

MaxTime

(2bytes Unit:s)

BatteryChange

(1byte Unit:0.1v)

Reserved

(4Bytes,Fixed 0x00)

Config

ReportRsp 0x81 Status

(0x00_success)

Reserved

(8Bytes,Fixed 0x00)

ReadConfig

ReportReq 0x02 Reserved

(9Bytes,Fixed 0x00)

ReadConfigR

eportRsp 0x82 MinTime

(2bytes Unit:s)

MaxTime

(2bytes Unit:s)

BatteryChange

(1byte Unit:0.1v)

Reserved

(4Bytes,Fixed 0x00)

（2）Read Configuration:

Downlink：023D000000000000000000

Response：

823D003C003C0100000000（Current configuration）

5.3 Example for MinTime/MaxTime logic

Example#1 based on MinTime = 1 Hour, MaxTime= 1 Hour, Reportable Change i.e. BatteryVoltageChange=0.1V

MaxTime MaxTime

Sleeping(MinTime) Sleeping(MinTime)

Note: MaxTime=MinTime. Data will only be report according to MaxTime (MinTime) duration regardless BatteryVoltageChange

value.

Example#2 based on MinTime = 15 Minutes, MaxTime= 1 Hour, Reportable Change i.e. BatteryVoltageChange= 0.1V.

MaxTime

Sleeping(MinTime) sleeping sleeping sleeping

0H 15th M 30th M 45th M 1H 2H

Example#3 based on MinTime = 15 Minutes, MaxTime= 1 Hour, Reportable Change i.e. BatteryVoltageChange= 0.1V.

MaxTime

sleeping sleeping ...

0H 15th M 30th M 45th M 1H 1H 10th M 1H 25th M 1H 40th M 1H 55th M 2H 10th M

Wakes up and

collects data

3.6V

Does not report

Wakes up and

collects data

3.6V

Does not report

Wakes up and

collects data

3.6V

Does not report

Wakes up and

collects data

REPORTS 3.6V

Wakes up and

collects data

REPORT 3.6V

Wakes up and

collects data

REPORTS 3.6V

Wakes up and collects data

3.5V |3.5-3.6|=0.1

REPORTS 3.5V

Wakes up and

collects data

3.5V

Does not report

Wakes up and

collects data

3.5V

Does not report

Wakes up and

collects data

3.5V

Does not report

Wakes up and

collects data 3.5V

Does not report

Wakes up and

collects data

3.5V

Does not report

Wakes up and

collects data

REPORTS 3.5V

Wake up and collects data

REPORTS 3.6V

Wakes up and collects data

REPORTS 3.6V

Wakes up and collects data

REPORTS 3.6V

Wakes up and

collects data

3.6V

Does not report

Users push the button,

REPORTS 3.5V.

Recalculate MaxTime.

Notes :

1) The device only wakes up and performs data sampling according to MinTime Interval. When it is sleeping, it does not

collect data.

2) The data collected is compared with the last data reported. If the data variation is greater than the ReportableChange value,

the device reports according to MinTime interval. If the data variation is not greater than the last data reported, the device

reports according to MaxTime interval.

3) We do not recommend to set the MinTime Interval value too low. If the MinTime Interval is too low, the device wakes up

frequently and the battery will be drained soon.

4) Whenever the device sends a report, no matter resulting from data variation, button pushed or MaxTime interval, another

cycle of MinTime/MaxTime calculation is started.

6. Installation

This product comes with waterproof function. It can be attached to the iron surface, or the two ends can be fixed to the wall with

screws.

1. The figure shows the vibration sensor (R718DB2)

applied to the scene of the mousetrap in the restaurant.

It can also be applied to the following scenarios:

Restaurant (rat)

Shopping mall supermarket (rat)

Engine room (rat)

When it is necessary to detect whether the object is

vibrating or moved.

2. Fix the vibration sensor of the vibration sensor on the

object that needs to be detected whether it is vibrating

(Take the mousetrap as a picture, as shown below).

3. When the sensor senses the vibration and the spring deforms, an

alarm message will be reported.

The vibration is “1”.

No vibration is “0”.

Andere Handbücher für R718DB2

Inhaltsverzeichnis

Andere netvox Zubehör Handbücher

netvox

netvox RA0701 Bedienungsanleitung

netvox

netvox R718VA Bedienungsanleitung

netvox

netvox Z713 Bedienungsanleitung

netvox

netvox R718DB Bedienungsanleitung

netvox

netvox R718EB Bedienungsanleitung

netvox

netvox R72615 Bedienungsanleitung

netvox

netvox R809A Bedienungsanleitung

netvox

netvox R718PB15A Bedienungsanleitung

netvox

netvox Z808B Bedienungsanleitung

netvox

netvox R718PQ Bedienungsanleitung

netvox

netvox R718LB Bedienungsanleitung

netvox

netvox R311B Bedienungsanleitung

netvox

netvox R311CB Bedienungsanleitung

netvox

netvox R718AD Bedienungsanleitung

netvox

netvox R718G Bedienungsanleitung

netvox

netvox R718DB2 Bedienungsanleitung

netvox

netvox R313M Bedienungsanleitung

netvox

netvox RA02C Bedienungsanleitung

netvox

netvox R718CN2 Bedienungsanleitung

netvox

netvox R311D Bedienungsanleitung

netvox

netvox R718VA Bedienungsanleitung

netvox

netvox R718J Bedienungsanleitung

netvox

netvox ZB11A1 Bedienungsanleitung

netvox

netvox R718PB13 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung