Nibe F1145-5 Benutzerhandbuch

Installer manual

LEK

NIBE F1145

Ground source heat pump

IHB GB 1643-2

331509

Quick guide

Navigation

Ok button (confirm/select)

Back button (back/undo/exit)

Control knob (move/increase/reduce)

A detailed explanation of the button functions can be found on page 38.

How to scroll through menus and make different settings is described on page 41.

Set the indoor climate

The mode for setting the indoor temperature is accessed by pressing the OK button twice, when in the start mode

in the main menu.

Increase hot water volume

To temporarily increase the amount of hot water (if a hot water heater is installed to your F1145), first turn the

control knob to mark menu 2 (water droplet) and then press the OK button twice.

Table of Contents

41 Important information

4Safety information

62 Delivery and handling

6Transport

6Assembly

7Supplied components

7Removing the covers

83 The heat pump design

8General

10Distribution boxes

12Cooling section

144 Pipe connections

14General

15Dimensions and pipe connections

15Brine side

16Heating medium side

16Water heater

17Docking alternatives

195 Electrical connections

19General

21Connections

23Settings

25Optional connections

29Connecting accessories

316 Commissioning and adjusting

31Preparations

31Filling and venting

32Start guide

33Post adjustment and venting

35Setting the cooling/heating curve

387 Control - Introduction

38Display unit

39Menu system

438 Control - Menus

43Menu 1 - INDOOR CLIMATE

43Menu 2 - HOT WATER

43Menu 3 - INFO

44Menu 4 - HEAT PUMP

45Menu 5 - SERVICE

569 Service

56Service actions

6210 Disturbances in comfort

62Info menu

62Manage alarm

62Troubleshooting

6511 Accessories

6712 Technical data

67Dimensions and setting-out coordinates

68Technical specifications

74Energy labelling

95Item register

99Contact information

3Table of Contents |NIBE F1145

Safety information

This manual describes installation and service procedures

for implementation by specialists.

This appliance can be used by children

aged from 8 years and above and per-

sons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use

of the appliance in a safe way and under-

stand the hazards involved. Children shall

not play with the appliance. Cleaning

and user maintenance shall not be made

by children without supervision.

Rights to make any design or technical

modifications are reserved.

©NIBE 2016.

Symbols

NOTE

This symbol indicates danger to machine or

person.

Caution

This symbol indicates important information

about what you should observe when maintain-

ing your installation.

TIP

This symbol indicates tips on how to facilitate

using the product.

Marking

The CE marking means that NIBE ensures that the

product meets all regulations that are placed on it based

on relevant EU directives. The CE mark is obligatory for

most products sold in the EU, regardless where they are

made.

Serial number

The serial number can be found at the bottom right of

the front cover and in the info menu (menu 3.1) and on

the type plate (PF1).

Serial number

Caution

You need the product's ((14 digit) serial number

for servicing and support.

Recovery

Leave the disposal of the packaging to the in-

staller who installed the product or to special

waste stations.

Do not dispose of used products with normal

household waste. It must be disposed of at a

special waste station or dealer who provides this type of

service.

Improper disposal of the product by the user results in

administrative penalties in accordance with current legis-

lation.

Environmental information

This unit contains a fluorinated greenhouse gas that is

covered by the Kyoto agreement.

F-Gas Regulation (EU) No. 517/2014

The equipment contains R407C, a fluorinated green-

house gas with a GWP value (Global Warming Potential)

of 1,774. Do not release R407C into the atmosphere.

Country specific information

Installer manual

This installer manual must be left with the customer.

NIBE F1145Chapter 1 | Important information4

1 Important information

Inspection of the installation

Current regulations require the heating installation to be inspected before it is commissioned. The inspection must

be carried out by a suitably qualified person. In addition, fill in the page for the installation data in the User Manual.

DateSignatureNotesDescription

✔

Brine (page 15)

System flushed

System vented

Antifreeze

Level/Expansion vessel

Particle filter

Safety valve

Shut off valves

Circulation pump setting

Heating medium (page 16)

System flushed

System vented

Expansion vessel

Particle filter

Safety valve

Shut off valves

Circulation pump setting

Electricity (page 19)

Connections

Main voltage

Phase voltage

Fuses heat pump

Fuses property

Outside sensor

Room sensor

Current sensor

Safety breaker

Earth circuit-breaker

Setting of emergency mode thermostat

5Chapter 1 | Important informationNIBE F1145

Transport

F1145 should be transported and stored vertically in a

dry place. When being moved into a building, F1145

may be leant back 45 °.

Caution

The product can be tail heavy.

If the cooling module is pulled out and transported up-

right, F1145 can be transported on its back.

Remove the outer panels in order to protect them when

moving in confined spaces inside buildings.

Extracting the cooling module

To simplify transport and service, the heat pump can be

separated by pulling the cooling module out from the

cabinet.

See page 58 for instructions about the separation.

Assembly

■Position F1145 on a fixed foundation that can take the

weight of the heat pump. Use the product's adjustable

feet to obtain a horizontal and stable set-up.

30 - 50 mm

15 - 40 mm

20-55 mm

■Because water comes from F1145, the area where the

heating pump is located must be equipped with floor

drainage.

■Install with its back to an outside wall, ideally in a room

where noise does not matter, in order to eliminate

noise problems. If this is not possible, avoid placing it

against a wall behind a bedroom or other room where

noise may be a problem.

■Wherever the unit is located, walls to sound sensitive

rooms should be fitted with sound insulation.

■Route pipes so they are not fixed to an internal wall

that backs on to a bedroom or living room.

Installation area

Leave a free space of 800 mm in front of the product.

Approx. 50 mm free space is required on each side, to

remove the side panels (see image). The panels do not

need to be removed during service. All service on F1145

can be carried out from the front. Leave space between

the heat pump and the wall behind (and any routing of

supply cables and pipes) to reduce the risk of any vibra-

tion being propagated.

(50) (50)

800

* A normal installation needs 300 – 400 mm (any side) for connec-

tion equipment, i.e. level vessel, valves and electrical equipment.

NIBE F1145Chapter 2 | Delivery and handling6

2 Delivery and handling

Supplied components

LEK

Room sensor

1 x

Current sensor

3 x

(not 1x230V)

Outside sensor

1 x

LEK

O-rings

8 x

Safety valve

0.3 MPa (3 bar)

1 x

Level vessel

1 x

WILO

LEK

WILO

2,5(22)

H- 50 - 2,5

TUV-SV-97-525

WILO

LEK

WILO

2,5(22)

H- 50 - 2,5

TUV-SV-97-525

Compression ring couplings

F1145 5-10 kW

2 x (ø28 x G25)

3 x (ø22 x G20)

F1145 12-15 kW

5 x (ø28 x G25)

F1145 17 kW

3 x (ø28 x G25)

2 x (ø35 x G32)

Particle filter

6-10 kW

1 x G1, 1 x G3/4

12-17 kW

1 x G1, 1 x G1 1/4

LEK

Insulation tape

1 x

Tubes for sensors

3 x

Temperature

sensor

3 x

LEK

Aluminium tape

1 x

Location

The kit of supplied items is placed in packaging on top

of the heat pump.

Removing the covers

Front cover

LEK

1. Remove the screws from the lower edge of the front

panel.

2. Lift the panel out at the bottom edge and up.

Side covers

LEK

The side covers can be removed to facilitate the installa-

tion.

1. Remove the screws from the upper and lower edges.

2. Twist the cover slightly outward.

3. Move the hatch outwards and backwards.

4. Assembly takes place in the reverse order.

7Chapter 2 | Delivery and handlingNIBE F1145

General

F1145

UB1

EB1

QM34

QM31

UB3

AA4

AA4-XJ3

UB2

QM32

AA4-XJ4

SF1

QM33

XL1

XL6 XL7

XL2XL9

QN10

PF1

PF2

BT2

W130

View from behind

BF1

NIBE F1145Chapter 3 | The heat pump design8

3 The heat pump design

Pipe connections

Connection, heating medium flowXL1

Connection, heating medium returnXL2

Connection, brine inXL6

Connection, brine outXL7

Connection, hot water heaterXL9

HVAC components

Shut-off valve, heating medium flowQM31

Shut off valve, heating medium returnQM32

Shut off valve, brine outQM33

Shut-off valve, brine inQM34

Shuttle valve, climate system/water heaterQN10

Sensors etc.

Flow meter**BF1

Outdoor temperature sensor*BT1

Temperature sensors, heating medium flowBT2

**Only heat pumps with energy meter

* Not illustrated

Electrical components

Display unitAA4

AA4-XJ3 USB socket

AA4-XJ4 Service outlet (No function)

Immersion heaterEB1

SwitchSF1

Network cable for NIBE UplinkW130

Miscellaneous

Rating platePF1

Type plate, cooling sectionPF2

Cable gland, incoming electricityUB1

Cable glandUB2

Cable gland, rear side, sensorUB3

Designations in component locations according to

standard IEC 81346-1 and 81346-2.

9Chapter 3 | The heat pump designNIBE F1145

Distribution boxes

F1145

FB1

FD1

AA1

FA1

AA3

AA2

Electrical components

Immersion heater cardAA1

Base cardAA2

Input circuit boardAA3

Miniature circuit-breakerFA1

Motor cut-out*FB1

Temperature limiter/Emergency mode thermostatFD1

* 1x230 V, 3x230 V 6-10 kW, 3x400V 5 kW has auxiliary switch for

motor cut-out.

Designations in component locations according to

standard IEC 81346-1 and 81346-2.

NIBE F1145Chapter 3 | The heat pump design10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nibe Wärmepumpe Handbücher

Nibe

Nibe SPS 10 Benutzerhandbuch

Nibe

Nibe F1255 Series Bedienungsanleitung

Nibe

Nibe F1355 Series Bedienungsanleitung

Nibe

Nibe S1255 Benutzerhandbuch

Nibe

Nibe F1255 Series Benutzerhandbuch

Nibe

Nibe F2025 Bedienungsanleitung

Nibe

Nibe F2030 Benutzerhandbuch

Nibe

Nibe F2300 Benutzerhandbuch

Nibe

Nibe F750 Bedienungsanleitung

Nibe

Nibe S1256PC Benutzerhandbuch

Nibe

Nibe S2125 Bedienungsanleitung

Nibe

Nibe F470 Bedienungsanleitung

Nibe

Nibe F1330 Bedienungsanleitung

Nibe

Nibe F1355 Series Benutzerhandbuch

Nibe

Nibe F2120-16 Bedienungsanleitung

Nibe

Nibe F1145PC Bedienungsanleitung

Nibe

Nibe AMS 10 Series Benutzerhandbuch

Nibe

Nibe F2120 Series Bedienungsanleitung

Nibe

Nibe F730 Benutzerhandbuch

Nibe

Nibe F110 Bedienungsanleitung

Nibe

Nibe CLIMATEMASTER TRANQUILITY 16 Series Betriebsanleitung

Nibe

Nibe F1155 Series Bedienungsanleitung

Nibe

Nibe F1330 Kurzanleitung

Nibe

Nibe F1155 Series Benutzerhandbuch

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung