Nilfisk-Advance C 125.4 Betriebsanleitung

Repair Manual

C 125.4

C 130.2

C-PG 130.2 X-TRA

Index

A. Safety precautions 3

B. Technical data 4

C. Construction 5-6

D. Service / Repair 7-11

F. Operating supplies 16

E. Torque 14-15

G. Operation 17-19

H. Diagram 20

Safety precautions.

WARNING!

 High pressure jets can be dangerous. Never direct the water jet at persons

pets, live electrical equipment or the machine self.

 The operator and anyone in the immediate vicinity of the site of cleaning

should take action to protect themselves from being struck by debris dis-

lodged during operation. Wear goggles during operation.

 Never try to clean clothes or footwear on yourself or other persons.

 Do not let children or people who have not read the instruction manual op-

erate the machine.

 Never use the machine in an environment where there could be a danger of

explosion. If any doubt arises, please contact the local authorities.

 It is not allowed to clean asbestos- containing surfaces with high pressure.

 This high pressure washer must not be used at temperatures below 0°C.

 Never let any persons stay under the product when stored on the wall.

Technical Data.

Product segment: Consumer C125.4 C130.2/C-PG 130.2

Specification bar Max 125 Max 130

Voltage V230 230

Frequency Hz 50 50

Power consumption A7,5 7,8

Power absorbed KW 1,7 1,8

Numbers of revolutions rpm./ min. 17500-18000 17000-18000

Water volume, HP l / min. 5,3-6,3 5,3-6,3

Pump pressure bar 85-100 90-105

Nozzle pressure bar 79-94 84-99

Opening pressure bar 115-140 115-140

Retaining time min. 55

Oil contents ml 80 80

Oil type LHM 32 LHM 32

Max water inlet temperature C40 40

Max water inlet pressure bar 10 10

High pressure hose length m6m Textile 8m Textile/soft

Suction height m0,5 0,5

Electric cable m5m 5m

Insulation class BB

Tightness IPX5 IPX5

Construction.

C 125.4 - C 130.2 - C-PG 130.2 X-TRA Construction of cabinet parts.

(!) Part 24, 25, 26 are on only used on PG versions

(!)

Construction.

C 125.4 - C 130.2 - C-PG 130.2 X-TRA Construction of pump unit.

Service / Repair.

Dismounting / mounting of front cabinet and accessory storage.

1. Tools: Torx 20 screwdriver and flat screw driver

2. Remove the handle by pressing the 2 * 2 snap locks (fig.2). Loosen one side first and

then the other side.

3. Remove the 2 torx (TX20) screws from the rear side (fig. 3)

4. Loosen the front cabinet from the accessories storage with a screw driver as shown on

fig. 4 from both sides. Take off the accessories storage.—When mounting the accesso-

ries storage to the front cabinet, there should be a “click” from the parts before to mount

the 2 screws.

5. Now the front cabinet can be lifted upwards to dismount it.

Fig. 1 Fig. 2

Fig. 3 Fig. 4 Fig. 5

Service / Repair.

Dismounting / mounting of Control Unit and/or Wireless Unit (Only PG version).

1. Tools: Torx 9 screwdriver

2. Controle Unit: Disconnect cable to Wireless Unit, Remove the 3 torx (T9) screws , ex-

change Controle Unit, dismount the 3 wires.

Mount and tighten the torx (TX9) screws Torque: max 0,8 Nm, and connect cable to Wire-

less Unit, check the circuit diagram and mount the 3 wires accordingly on the Control Unit

3. Wireless Unit: Disconnect cable to Wireless Unit, slide the Wireless Unit out, exchange

the wireless Unit, slide the Wireless Unit back, and connect cable to Wireless Unit.

Check how to reconfigure the pairing of the machine and the PowerGrip handle at page xx

Fig. 1

Fig. 2 Fig. 3

Service / Repair.

Exchange battery (cell type: CR 2032 ) in PowerGrip handle.

1. Dismount the screw (Phillips) and the cover to the battery. Dismount the old battery

2. Ensure that the new battery is mounted with the right polarity in the battery holder

3. Mount the battery cover and mount the screw

Pairing of the machine and the PowerGrip handle (Only PG version).

Pairing of the wireless devices is needed if:

 the PowerGrip has been exchanged

 the Wireless Unit in the PowerGrip has been exchanged

 the Control Unit in the machine has been exchanged

 the Wireless Unit has been exchanged in the machine

 Or if the user hasn’t paired the machine and the PowerGrip handle

Pairing of the machine and the PowerGrip handle:

1. Ensure that the machine is not turned on

2. Dismount the battery and mount the battery again

3. Orange indicator on the handle is now blinking in approx. 2 minutes, indicating that the

handle is in pairing mode.

4. Turn on the machine within the 2 minutes of pairing mode, when the orange indicator

stops blinking, the handle and the machine has been paired and can now be operated.

Service / Repair.

Fig. 1 Fig. 2

Fig. 4Fig. 3

Dismount / mounting of motor cover.

1. Place the cleaner on the side and remove the 5 torx 20 screws. Fig 1

2. Remove the wheel to remove the 5th. Screw if the torx screw dirver is too short. Fig 2

3. Now the cabinet can be removed and the motor / pump unit can be taken out. Fig 3 & 4

The micro switch box is removed by hand. It can be hard but it is just to be “broken” off!

When mounting the MPU again, first step is to mount the micro switch box. This can be done

by hand (alternatively use a plastic hammer), but be very careful to mount in the correct posi-

tion) Then place the MPU inside the cabinet.

Andere Handbücher für C 125.4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nilfisk-Advance Hochdruckreiniger Handbücher

Nilfisk-Advance

Nilfisk-Advance C 120.4 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance POSEIDON 2 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Hybrid 7 MH42 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance MC DE Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance N/G-4001A Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance MH 1C Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance C 100.7 Betriebsanleitung

Nilfisk-Advance

Nilfisk-Advance Nilfisk C 120.5 X-TRA Betriebsanleitung

Nilfisk-Advance

Nilfisk-Advance SelectSpray 1250E Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance P 150.2 X-TRA Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance C 110.3 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC UNO Series Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance ALPHA BOOSTER 3 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance APC 328 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance MC 2C Series Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Nilfisk C 120.3 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance NEPTUNE 4 FA Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance P 150.1-10 B Betriebsanleitung

Nilfisk-Advance

Nilfisk-Advance Core 140 Powercontrol Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SelectSpray 1500E 56011781 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance C 125.4 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance TITAN X-TRA Firmware-Update

Nilfisk-Advance

Nilfisk-Advance E130.3 X-TRA Betriebsanleitung

Nilfisk-Advance

Nilfisk-Advance C-PG 135.1 Bedienungsanleitung

Beliebte Hochdruckreiniger Handbücher anderer Marken

Shark

Shark RG-232637 Bedienungsanleitung

Shakti Technology

Shakti Technology S3 Bedienungsanleitung

Kärcher

Kärcher K 4 Pure Bedienungsanleitung

Porter-Cable

Porter-Cable D25806-025-2 Bedienungsanleitung

REM POWER

REM POWER HDEm 662 Bedienungsanleitung

Landa

Landa HS-3000 Bedienungsanleitung

Craftsman

Craftsman 580.752270 Bedienungsanleitung

HIKOKI

HIKOKI AW 100 Bedienungsanleitung

Delco

Delco DC 1302 Bedienungsanleitung

Kärcher

Kärcher K 3 Full Control Bedienungsanleitung

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Bedienungsanleitung

ARKSEN

ARKSEN 014-HG-14141-HR Bedienungsanleitung

Black & Decker

Black & Decker PW1700SPX Bedienungsanleitung

Kärcher

Kärcher 595 - SPARE Leitfaden

Kranzle

Kranzle B 10 200 Bedienungsanleitung

Stihl

Stihl RE 90 Bedienungsanleitung

Husky

Husky HU80911 Bedienungsanleitung

PowR-Quip

PowR-Quip PQ-2600 Bedienungsanleitung