Nilfisk-Advance GM 811 Bedienungsanleitung

GM 810 GM 811

Instructions for use

823 0054 000 C (03. 2017)

GM 810 811US Front cover 2008 A4.indd 1 2008-08-07 13:30:48

Nilfisk GM 810-811

INSTRUCTIONS FOR USE &

PARTS LIST

Table of Contents

Important Safety Instructions

Warranty

Machine Setup

Using the Machine

Emptying

Disposal

Maintenance/Filter Replacement

Troubleshooting

Loss of Power

Loss of Suction

Technical Specifications 7

For Instructions for Use on HEPA/ULPA filter installation, please refer to

the addendum titled, “ABSOLUTE FILTERS – End User Information.”

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE USING THE

MACHINE. DEPENDING ON LOCAL REGULATIONS AND THE COMPOSITION

OF THE MATERIALS YOU HAVE COLLECTED, THERE MAY BE

REQUIRMENTS FOR SPECIAL HANDLING AND DISPOSAL OF THE

COLLECTED DEBRIS. CONSULT YOUR LOCAL OCCUPATIONAL SAFETY AND

HEALTH ADMINISTRATION (OSHA) AND ENVIRONMENTAL PROTECTION

AGENCY (EPA) OFFICIALS FOR DETAILS.

CAUTION: This Nilfisk vacuum cleaner or any other vacuum cleaner is not to be used in

explosion-hazardous areas, as serious injury could result.

Under no circumstances may thiscleaner safely be used for the collection of hazardous or

toxic materials unless equipped with a special HEPA* filter and bag which have been

installed according to written instructions fromNilfisk.

ATTENTION EMPLOYER: Please ensure these Instructions for Use are made available

and understood by your employees or any other persons who may use this equipment.

To list all toxic and hazardous materials would bebeyond the scope of these Instructions.

It is the Employer's responsibility to identify, for Employees' and others' information,

hazardous ortoxic materials which may be collected by this equipment.

Your new Nilfisk industrial vacuum cleaner is a precision-engineered instrument

designed for exceptionally fine filtration. Ordinary vacuum cleaners do not have HEPA

filters, and cannot be safely used for hazardous dust collection. This Nilfisk machine is

safe to use with fine powders or hazardous materials, as long as certain precautions are

taken. Proper care of this cleaner is essential to the maintenance of its ultrafine filtering

capabilities.

BEFORE USE: DO NOT ATTEMPT TO OPERATE THIS CLEANER UNTIL YOU

HAVE INSTALLED ITS VARIOUS COMPONENTS ACCORDING TO THE

FOLLOWING INSTRUCTIONS:

WARRANTY

The Nilfisk companies warrant that Nilfisk equipment will be free of defects in

workmanship or material for a period of two years from the date of delivery. Should any

failure to conform tothis warranty appear, the Nilfisk companies shall upon notification

within such time period, correct such non-conformity, at its option, either by repairing

any defective part or parts, or by replacing apart or parts provided thatthe equipment is

returned to an authorized Nilfisk service facility. In all cases freight both wayswill be at

the expense of the customer. Equipment shall not be returned without advance notice to,

and consent of the Nilfisk companies.

EXCEPT AS SPECIFICALLY SET FORTH HEREIN, THE NILFISK COMPANIES

MAKE NO WARRANTIES, EITHER EXPRESSED OR IMPLIED AS TO ANY

MATTER WHATSOEVER, INCLUDING WITHOUT LIMITATION ANY AND ALL

WARRANTIES OF MERCHANTABILITY, FITNESS FOR PURPOSE, OR OTHER

WARRANTIES, ALL OF WHICH ARE EXPRESSLY DISCLAIMED AND

EXCLUDED. NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES,

INCLUDING BUT NOT LIMITED TO LOSS OF PRODUCTION, LOSS OF TIME,

LOSS OF PROFITS OR OTHER SIMILAR INDIRECT LOSSES WHICH MIGHT

OCCUR AS A RESULT OF DEFECTS, PARTIAL OR TOTAL FAILURE OF THE

PRODUCT TO PERFORM AS SPECIFIED.

Correction of non-conformities or defects in the manner and for the period of time

provided above, shall constitute fulfillment of all liabilities of the Nilfisk companies to

the customer, whether based on contract, negligence or otherwise with respect to, or

arising out of such equipment. The remedies set forth herein are exclusive, and the

liability of the Nilfisk companies with respect to this sale or anything done in connection

therewith, whether in contract, in tort, under any warranty, or otherwise, shall not except

as expressly provided herein, exceed the price of the equipment or part on which such

liability is based.

The warranty does not cover repairs due to normal wear and tear, accident, neglect,

misuse or abuse, incorrect installation or use other than as described in the

instruction booklet. Breaks in hoses and cables are not covered. This warranty is

rendered void if the motor number plate is removed or defaced or if repairs are

made or attempted by persons not authorized by the Nilfisk companies.

MACHINE SET-UP:

Before turning on the motor: Install the microfilter (#616821-Felt,

#017230-AES Polycomposite, #017220-01-Gore-Tex®), the small

felt sock, on the bottom of the motor by sliding the filter over the

motor bottom, and covering as much of the bottom as the depth of

the filter will permit (photo 1). Be sure the filter's elastic collar

holds the filter snugly in place and is as high up on the motor

bottom as possible.

2. Next, mount the HEPA/ULPA filter (#01710440/01710440)

according to the accompanying bulletin. Place the motor back in

the cavity in the top of the cleaner (photo 2). Fasten the motor head

in place using either the positive twist safety latches or the

standard latches, depending on which option you purchased.

Photo 1

Photo 2

3. Installing the Polyliner and Paper Bag: Unsnap the two positive

twist safety latches, or the standard latches, depending on your

machine. They are located at the body of the container, front and

back. Lift off the top. Open the polyliner and place in the bottom

of the container with its walls flush against the container sides and

lipped under the container inlet (photo 3). The excess length of

polyliner is draped over the top of the container and down the

outside then rolled at the end to permit the container clips to

close.

Install a paper bag inside the polyliner according to the

illustrations printed on the paper bag itself (photo 4). Replace the

top container and fasten the two clips.

Photo 4

4. The GM 810 and GM 811 offer a wide variety of hoses and accessories. Consult your

local District Sales Managers or Customer Service Department at (800)-NILFISK for a

list of optional hoses and accessories. No matter what hose option you have chosen, it can

be connected in the following manner. Affix the vacuum hose to the vacuum by inserting

it into the orifice on the lower container. Once it is inserted, rotate the inlet coupler a

quarter turn to lock it into place. Consult your District Manager or the Customer Service

Department if you have any problems attaching the accessories you have purchased.

USING THE MACHINE:

Correct use of the machine: This machine is not a wet/dry vacuum. It is intended for dry

collection only. Do not use this vacuum to pick up liquids, or any wet materials in

general.

EMPTYING:

IF THIS VACUUM CLEANER IS USED TO COLLECT HAZARDOUS MATERIAL,

DO NOT ATTEMPT TO OPEN OR EMPTY ITS CONTENTS WITHOUT PERSONAL

PROTECTIVE CLOTHING AND RESPIRATORY PROTECTION.

Photo 3

Photo 4

Starting and stopping: Press the gray button on the upper

front portion of the vacuum (photo 5).

Photo 5

Photo 6

DISPOSAL:

Depending on local regulations, and the composition of the material you have collected,

there can be a requirement for special handling and labeling of the filled and sealed

plastic bags. Consult you local Occupational Safety and Health Administration (OSHA)

and Environmental Protection Agency (EPA) official for details.

MAINTENANCE

Routine Maintenance:

To ensure maximum performance of your Nilfisk vacuum cleaner, be sure to check your

main filter regularly. Your filter may need to be shaken out to remove caked dust from

time to time.

Filter Replacement:

To ensure that your Nilfisk vacuum cleaner delivers the years of trouble-free operation

for which it was designed, it is necessary to check and replace filters regularly.

1. Main Filter: The large napped cotton bag which is semi-

permanently mounted inside the container will not require

frequent replacement. The main filter must be replaced when

the cleaner no longer develops powerful suction, yet bags are

not full and other filter components are not clogged. Extend

main filter service life by frequent changes of disposable

polyliners and paper bags (photo 7).

2. Microfilter: This small aqua green (yellow if equipped with AES Polycomposite

microfilter) felt sock, which fits over the motor bottom will require periodic

inspection. Dust will discolor the microfilter. Change the microfilter as soon as any

discoloration is easily noticeable. Do not shake this microfilter since this can cause

liberation of potentially harmful microscopic dust into the air. Carefully remove and

To empty the container and its contents, first turn off the motor.

Allow the cleaner to sit undisturbed for at least thirty (30)

seconds. Then unsnap the container clips. Once the seal is

broken, turn on the motor again. This will prevent ultrafine

particles which are still suspended in the air inside the container

from escaping into the work place. Lift off the container top.

Remove the polyliner and paper bag within it (photo 6). Then

seal off the polyliner with the paper bag inside and install a new

polyliner and paper bag according to step 2, Machine Setup.

Photo 7

discard with collected debris in the sealable poly bag. If equipped with a Gore-Tex

microfilter, the same rules for periodic inspection and disposal apply. The Gore-Tex

microfilter must be changed when any abrasions, damage or heavy discoloration is

noticed on the surface of the filter (refer to photo 1).

3. HEPA or ULPA Exhaust Filter: This cartridge is mounted on

the top of the motor, outside the container. If the main filter

and microfilter are properly maintained, the glass fiber

element in the exhaust filter should perform satisfactorily for a

minimum of one year. It cannot be renewed or restored. Exact

life will depend upon frequency of use and amount and type

of material collected. Normally four changes of microfilter

equal one change of HEPA/ULPA filters. Remove the

protective metal casing and replace the pleated glass fiber

cartridge according to the accompanying instructions (photo

8). Cartridges must be replaced more frequently if the cleaner

has had unusually heavy use, or if the various pre-filters have

been neglected.

CAUTION: Use only genuine Nilfisk replacement filter components. The use of

substitute components could pose a grave risk of personal exposure, and will cause all

equipment warranties to be void.

TROUBLESHOOTING

Loss of Power:

1. Make sure the power cord is properly fastened to the motor head, and it is properly

plugged into the socket.

2. Be sure the electrical circuit has not blown a fuse.

3. If the circuit is functioning properly, but there is still no power, contact our Customer

Service Department at (800) 645-3475, extension 2.

Loss of Suction:

If the GM 80 loses suction power during operation, there may be several reasons,

the most likely of which is a full container. Suction loss is gradual as the container fills

with debris. Check to see if there is any blockage or restriction in the hose.

1) Check the condition of the main filter and microfilter (refer to photos) and determine

whether there is an excessive loading of debris. If there is overloading in the main

filter, you can shake it out. If the problem exists with the microfilter, it needs to be

replaced. Call our Customer Service Department at (800) 645-3475, extension 2 to

order a replacement.

2) If all fails, call our Customer Service Department at (800) 645-3475, extension 2.

Photo 8

TECHNICAL SPECIFICATIONS

Motor type, grounded GMPJ

Tank capacity 3 1 /4 gallons

Voltage @ 60 Hz. 110-120/220 volt

Paper bag capacity 2 1 /4 gallons

Current draw 9 amps

Filter area** 1477 square inches

Power watts 1100

Dimensions (l x w x h) 14x12x16 inches

Waterlift*, max. 102 inches H2O

Weight without accessories 11 lbs.

Airflow, max. 87 cfm

Cord length 30 feet

Air performance 250 air watts

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nilfisk-Advance Staubsauger Handbücher

Nilfisk-Advance

Nilfisk-Advance VHC200 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance GM 80CR Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Coupe Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Multi 20 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance HSC 585 Multi Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Nilfisk GD 2000 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance GWD 375 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance VHC200 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Elite Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance AERO 26 M Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Chalet CV 791 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 3707 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance VP300 eco Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance CFM WSS 100 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance BUDDY 15 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Multi 20 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SMART Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 56315044(855) Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance AERO 26-01 X Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance GD 1000 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SD 43-165 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance GD 110 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance WDNI-1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance GM 80 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch