Nokia CARK-91US Bedienungsanleitung

Complete Car Kit

(CARK-91US/CARK-91H)

For use with Nokia 5100 and 6100 Series

Wireless Phones

CARK-91USANDH07.26.00.fm Page 0 Wednesday, July 26, 2000 1:56 PM

Introduction

This installation guide has been prepared to provide the

basic information necessary to install this car kit. This guide

is not intended to be definitive, because different types and

models of vehicles will require different installation work.

The information given is for general guidance only.

The terms of warranty demand that this car kit be installed by

an experienced installation facility. An end user should never

attempt to install this car kit without professional assistance

as the installation requires special tools and knowledge.

Please refer to the phone’s Owner’s Manual for instructions

on the phone’s operation, care and maintenance, including

important safety information.

Note: Read the warnings below before beginning the instal-

lation procedure.

WARNINGS

1) Ensure that the vehicle’s battery is disconnected before

you start the installation procedure, and that it remains

disconnected during the procedure.

2) Do not smoke or use open flames when working near

the vehicle’s fuel system.

3) Ensure that the vehicle’s electrical cables, hydraulic

lines, fuel lines and safety equipment are not damaged

during installation.

4) Ensure that normal control and operation of the vehicle

is not impaired by the installation, particularly the

brakes and steering.

5) Electronic and other sophisticated systems

(e.g. speed control, abs anti-lock brake, fuel injection,

navigation and air bag systems) are relatively immune

to malfunction caused by nearby radio transmissions.

However, should you experience false operation of

these systems or are in any doubt whatsoever as to

their functionality, please consult the vehicle’s dealer.

CARK-91USANDH07.26.00.fm Page 1 Wednesday, July 26, 2000 1:56 PM

6) The car kit is suitable for use only in vehicles with a

11-32 V negative grounding. Use on other supply vol-

tages or alternative polarity will damage the equipment.

7) The phone should not be left switched on for extended

periods without running the vehicle’s engine. Failure to

comply could drain the vehicle’s battery.

Unpacking

Carefully unpack the equipment and ensure that the follow-

ing items are present.

Advanced Cradle MCC-1

RF Adapter AAC-1

Junction Box HFU-2

Power Cable PCH-4J

Mounting Plate MKU-1

Swivel Mount HHS-9

Microphone HFM-8

External HF Speaker HFS-12

Options

External Audio Handset (included with CARK-91H) HSU-1

CARK-91USANDH07.26.00.fm Page 2 Wednesday, July 26, 2000 1:56 PM

Component Parts

Advanced Cradle MCC-1

The Advanced Cradle firmly holds the phone in a conve-

nient place. The Advanced Cradle is attached to the

vehicle’s interior using the swivel mount HHS-9.

RF Adapter AAC-1

The RF Adapter converts the FME connector of the

MCC-1, Advanced Cradle, into a mini-U connector that

attaches to an external antenna.

Junction Box HFU-2

The Junction Box enables the phone to operate in hands-

free mode. The unit is attached to the vehicle interior using

the Mounting Plate MKU-1, or the Swivel Mount HHS-9.

A temporary installation can be achieved using cable ties.

Power is supplied from the vehicle’s battery via the Power

Cable PCH-4J. The Junction Box provides the power

supply to the phone via the system connector.

The HF Microphone HFM-8, connects to the MIC socket

and the External HF Speaker HFS-12, connects to the

socket.

Mounting Plate MKU-1 and Swivel Mount

HHS-9

MKU-1 is a fixed position mounting plate. The HHS-9 is a

Swivel Mount which allows for adjustable fixing. Both

mounting plates are interchangeable.

HF Microphone HFM-8

The HF Microphone connects directly to the socket of the

Junction Box HFU-2, marked MIC.

HF Speaker HFS-12

The HF Speaker connects directly to the handsfree unit

socket. Insert the plug into the socket and twist 90°

to lock firmly in place.

CARK-91USANDH07.26.00.fm Page 3 Wednesday, July 26, 2000 1:56 PM

Power Cable PCH-4J

The power cable connects the Junction Box HFU-2, to the

vehicle’s power supply. The red wire must be connected to

the + voltage on the vehicle’s power supply via the supplied

fused connector. The black wire must be attached to a

good negative GND connection.

The blue ignition sense (IGNS) wire is connected to +12 V

voltage controlled by the vehicle’s ignition key via the sup-

plied fused connector. (See section “Ignition Sense”.)

The yellow wire is used for car radio muting (XCRM). The

line goes down to 0 volts during a call. (See section “Car

Radio Muting”).

The green wire is used for motor antenna (AMC). The vol-

tage in this output is +12 V whenever the phone is on.

(See section “Antenna Motor Control”).

HSU-1 External Audio Handset (included

with CARK91H, optional for CARK-91US)

The External Audio Handset is a

simple handset with no display or

keypad. It provides privacy for

conversation and comfort in a

vehicle’s noisy environment.

However, do not use the handset

while in motion, as both hands

are needed for safe driving. The

External Audio Handset (HSU-1)

is not included in the Complete

Car Kit, (CARK-91US).

Handset Operation

To make a call with External Audio Handset (HSU-1)

1) Key in the desired number on the keypad of your phone.

2) Press ó(6100) or +&DOO,(5100) and lift the

handset.

To receive a call with External Audio Handset

• Lift the handset or press any key except for the power

key, ôor the volume keys.

CARK-91USANDH07.26.00.fm Page 4 Wednesday, July 26, 2000 1:56 PM

When you lift the Audio Handset from its holder, the

HF-loudspeaker and HF-microphone will be muted and

you can speak in privacy.

To end a call with External Audio Handset

• Replace the handset or press ô(6100) or #

+(QG,(5100).

To switch from handsfree (HF) operation to handset

operation

•Liftthehandset

To switch from handset operation to handsfree (HF)

operation

• Press the left ñ2SWLRQV soft key (6100) or

+2SWLRQV,(5100) once and replace the handset in

5 seconds. If you do not press the left ñ2SWLRQV

(6100) or #+2SWLRQV,(5100) the call will

terminate!

External Mobile Antenna (not included)

The wireless phone is designed to operate with a high quality

external antenna. Due to many different types of antennas,

an antenna is NOT included as part of this kit. Please, con-

sult the dealer to find out which is the most suitable

antenna type for your installation. Please note that the

antenna is required for proper operation.

Installation

Special attention must be given to the positioning of the car

kit accessories.

The positioning of the Active Cradle MCC-1 is the most im-

portant factor when trying to achieve the most comfortable

position for the user. The location of the cradle should be

selected so that the visibility of the phone’s display is good

under all lighting conditions, but not so that the driver’s

attention is easily distracted. The cradle should be located

so that the driver can easily reach the keypad. Under no

circumstances should the cradle prevent the driver from

CARK-91USANDH07.26.00.fm Page 5 Wednesday, July 26, 2000 1:56 PM

controlling or operating the vehicle in any way or obstruct

the driver’s view of traffic.

The Junction Box HFU-2 can be installed in a hidden loca-tion

since there is no need to disconnect cables during

normal operation. Ensure that the microphone is as close

to the driver’s mouth as possible, and attached to a surface

that is mechanically quiet. The microphone should be

mounted at least 3 ft/1 m away from the handsfree unit

speaker to avoid acoustic feedback.

Ensure that cables are routed as far away as possible from

the vehicle’s electronic systems (refer to WARNINGS)*.

Also, ensure that cables are not subjected to undue

mechanical stress e.g. under seats or against sharp edges.

The external antenna unit should always be connected to

the antenna via a non-radiating cable (e.g. coax).

* To prevent disturbance, cables should be routed as far

away from the interference source as possible

Caution: In order to comply with FCC RF exposure requirements

for mobile transmitting devices, install the antenna so that a

minimum distance of 20 cm can be maintained between the

antenna and all persons, with antenna gain not exceeding 3 dBi.

Ignition Sense IGNS

The ignition sense feature prevents the transceiver from

draining the car battery by executing an auto power off in

20 seconds after the ignition key has been turned off. The

blue wire of the power cable is used for the ignition sense

feature. The use of ignition sense is recommended to pre-vent

accidental draining of the car’s battery. The wire is

connected via a 1 A fuse to a 12/24 volt potential that is

controlled by the ignition key. Do not connect it directly to

the high voltage sections of the ignition circuit.

Car Radio Muting XCRM

The car kit offers a feature that can mute the car radio

automatically during a conversation. This feature is con-

venient and provides for safer handsfree operation. When

in standby, the yellow wire (XCRM) is not grounded and the

car radio works normally, but during a call, the line is

grounded and the car radio is muted. Note that an auxiliary

relay or muting unit must be used when the car radio

doesn’t have a mute feature available.

When a relay is used, it is connected in series with the car

radio main supply. A 200 mA fuse should be used to

protect the XCRM output in event of a short circuit. Some

radios have separate supplies for amplifiers and motors,

and another for memory backup purposes. Very often

these radios also have a secret code system, which acti-

vates itself if a break in the memory supply is detected.

Be careful when installing the relay not to break the mem-

ory supply (usually ma rked ACC or +MEM), but to install the

relay in the main supply feed.

Another possibility is to use a special muting unit, which

mutes the radio by connecting load resistors (not included)

to the speaker lines of the car radio.

Note: The Car Radio Mute option might not interface with

certain OEM and Aftermarket car stereos due to differing

electronics.

Antenna Motor Control AMC

The Antenna Motor Control offers the option to retract a

power AM/FM cellular antenna when the phone is in the

CARK-91USANDH07.26.00.fm Page 7 Wednesday, July 26, 2000 1:56 PM

cradle (the system cable’s green wire). This allows the

phone to operate with the antenna without having to turn

on the car’s ignition. The voltage in this output is +12 V

whenever the phone is on. If the phone is turned off, the

voltage disappears. The maximum output current is 200 mA,

therefore for example the motorized antenna must be

controlled via a relay, see picture on next page.

Note: Please consult the dealer or car manufacturer about

antenna options available for your automobile. A dual mode

antenna is recommended when using a Nokia 6160

wireless phone.

All installations should take into account any special

requirements of the customer. However, should the cus-

tomer require an installation that is illegal or unsafe these

facts must be pointed out to the customer and a policy of

non-compliance adopted.

Te s t i n g

Once installed, the equipment should be tested to ensure

that it is operating satisfactorily and that the position of the

unit does not impair on the driver’s ability to control and

operate the vehicle in any way.

Use the phone to make a call when the vehicle is parked

with the engine running. During the call, switch off the

engine. Ensure that the phone is operational with the engine

running and with the engine switched off. For operating

information refer to the phone’s owner’s manual.

CARK-91USANDH07.26.00.fm Page 8 Wednesday, July 26, 2000 1:56 PM

NOTES

CARK-91USANDH07.26.00.fm Page 9 Wednesday, July 26, 2000 1:56 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nokia Autozubehör Handbücher

Nokia

Nokia HF-21W Originalbetriebsanleitung

Nokia

Nokia HH-12 Bedienungsanleitung

Nokia

Nokia CK-100 Bedienungsanleitung

Nokia

Nokia CK-15W Handbuch

Nokia

Nokia CK-200 Handbuch

Nokia

Nokia HF-6W - Bluetooth hands-free Car Bedienungsanleitung

Nokia

Nokia CARK-91H Leitfaden

Nokia

Nokia Cellphone 3600 Bedienungsanleitung

Nokia

Nokia CK-600 Merkblatt

Nokia

Nokia HF-23 Handbuch

Nokia

Nokia CK-300 Bedienungsanleitung

Nokia

Nokia CK-7W Handbuch

Nokia

Nokia CK-10 Bedienungsanleitung

Nokia

Nokia CARK-91 Bedienungsanleitung

Nokia

Nokia CK-20W - Multimedia Car Kit Merkblatt

Nokia

Nokia CK-100 Bedienungsanleitung

Nokia

Nokia HF-33W - Wireless Plug-in Car Handsfree Bedienungsanleitung

Nokia

Nokia CAR KIT CK-100 Handbuch

Nokia

Nokia Cark-112 Bedienungsanleitung

Nokia

Nokia HF-33W - Wireless Plug-in Car Handsfree Bedienungsanleitung

Nokia

Nokia CK-7W Bedienungsanleitung

Nokia

Nokia CK-1W Bedienungsanleitung

Nokia

Nokia CK-300 Merkblatt

Nokia

Nokia CR-200 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung