Norac UC4+ Bedienungsanleitung
Procedure for Testing
UC4+, UC4 and UC3 Sensors
Printed in Canada
Copyright 2006 NORAC Systems International Inc.
Reorder P/N: 44645-MAN1 Revision I
NOTICE
NORAC Systems International Inc. reserves the right to improve products and their
specifications without notice and without the requirement to update products sold
previously. Every effort has been made to ensure the accuracy of the information contained
in this manual. The technical information in this manual was reviewed at the time of approval
for publication.
Spray Height
Controller
Contents
1Introduction.................................................................................1
2Materials....................................................................................... 2
3CANbus Monitor Parts...............................................................3
4Setting Up.................................................................................... 4
5Testing UC4+ and UC4 Sensors................................................8
6Testing UC3 Sensors ................................................................12
7Replacing Transducers .............................................................13
8Replacing O-Rings .....................................................................16
9Frequently Asked Questions....................................................17
10Log Sheet ...................................................................................19
11Appendix A – Adjusting 44730 Calibration Stand................. 23
1
1Introduction
This manual serves as an instruction manual for testing UC4+, UC4 and
UC3 sensors. This procedure is useful in determining if a sensor needs to
be returned to NORAC for repairs or if it is possible to continue using it.
This procedure also provides a method for performing some basic
calibration of the UC4 sensor to improve its performance. The procedure
requires special components that may be purchased from NORAC.
Phone: 1-800-667-3921 Canada (Toll Free)
1-866-306-6722 United States (Toll Free)
(+33) (0)4 26 47 04 42 Europe
1-306-664-6711 all other regions
E-mail: [email protected]
Web Site: www.norac.ca
2
2Materials
Table 1: Items included in the UC4 Resource Kit
Item Part Number Name Quantity
B01 44968 ULTRASONIC SENSOR CALIBRATION FIXTURE TYPE2 1
C01 44644-04 CABLE BUSMONITOR POWER STAND-ALONE DEVICE 1
E01 54733 NORAC USB DRIVE - TOOLSUITE AND VERIFICATION TOOL 1
E02 44644 CANBUS MONITOR 1
M01 44645-MAN1 MANUAL UC4 SENSOR TESTING 1
M02 44645-MAN2 MANUAL UC4 PANEL PROGRAMMING 1
**M05 106127 ADH RTV 162 WHITE SILICONE - 85mL TUBE 1
*M06 44645-02 TRANSDUCER SERVICE KIT 1
*M07 44645-03 O-RING SERVICE KIT 2
*M08 44645-04 FOAM DISC SERVICE KIT 1
The following items are not included in the test kit, but are required for
testing and updating UC4 sensors and panel software:
12 VDC (2A or greater) power supply1
Computer with Windows operating system.
* Items M06, M07 and M08 are available for re-order from NORAC.
** Item M05 is available for re-order from NORAC, as well as from the
manufacturer:
Item # Description
Manufacturer
Part #
M05 ADH RTV 162 WHITE
SILICONE - 85mL TUBE
MG Chemicals
/Momentive
RTV162-
85mL
1Recommended power supply:
Catalog #22-507 available from RadioShack (United States)
Catalog #2208247 available from The Source (Canada)
3
3CANbus Monitor Parts
Figure 1: The NORAC CANbus Monitor Connections
Bus Monito
r
CANbus
Connector
Panel
Programming
Adapter
USB to Serial
Adapter
4
4Setting Up
* Refer to Appendix A for setup and calibration of the 44730
calibration stand.
4.1 Assemble the two parts of the test stand as shown in Figure 2.
Insert the sheet metal insert into the rectangular hole. Install the
spring, flat washer and wing nut onto the stud. Tighten wing nut until
the spring is approximately half compressed.
Figure 2: Test Stand Assembly
457 mm
(18”)
5
4.2 Insert the alignment tool (44968-2) into the test stand. (Figure 3)
4.3 Adjust the threaded mount (A) of the golf ball target so the surface of
the ball will touch the tip of the alignment tool (it may be necessary to
align the calibration stand first (Step 4.4) before this is possible.
4.4 Using the adjustment screws (B and C), align the tip of the alignment
tool to the center of the golf ball
To move the tip of the rod upwards, turn both adjustment screws
in an equal amount.
To move the tip of the rod downwards, turn both adjustment
screws out an equal amount.
To move the tip of the rod side to side, turn one screw in and one
screw out an equal amount.
4.5 Rotate the alignment tool 180 degrees and repeat the alignment
process (Step 4.4). If after rotating the alignment tool the tip of the
rod is not centered on the ball target, split the difference of the two
calibrations.
4.6 It may be necessary to adjust the threaded mount of the ball target (A)
after Step 4.5.
Figure 3: Test Stand Alignment
6
4.7 If the test stand is ever disassembled, it must be realigned when
reassembled. Use the alignment tool to check the alignment of the
test stand before each use.
4.8 Inspect the sensor for visible damage. Inspect the transducer by
removing the foam and looking through the screen. The underlying
gold foil should be clean and free from tears, chemical deposits or
wrinkles. Ensure a clean foam disc is in the sensor before testing.
NOTE: It is advised that a new foam disc is used for sensor
testing.
4.9 Mount the sensor into the sensor test stand. Press the handle
towards the stand and insert the sensor with the transducer facing the
golf ball as shown in Figure 4.
Figure 4: Sensor Mounted in Test Stand
4.10 Attach the USB end of the USB-to-Serial Adapter to the computer and
ensure that the Serial end is attached to the Bus Monitor.
4.11 Connect the Bus Monitor’s Power connector labeled “To CANBus”
to the Bus Monitor Stand-Alone Power Cable connector labeled “To
Bus Monitor”.
4.12 Connect the banana plugs on the Bus Monitor Stand-Alone Power
Cable to a 12Vdc power supply.
4.13 The red banana plug must be connected to the positive terminal and
the black banana plug to the ground.
4.14 Switch the power supply on, check that the LED on the Bus Monitor is
7
illuminated and switch off power supply.
4.15 Connect the sensor cable to the Bus Monitor Stand-Alone Power
Cable AMP connector labeled “To CANBus”.
4.16 Once the sensor is connected to the Bus Monitor, turn on the power
supply and allow the sensor to run for at least 5 minutes before
proceeding to Section 5.
Figure 5: Bus Monitor Connections
Power
Supply
Bus
Monito
r
Connect
to Sensor
Serial
–
USB
A
dapte
r
Stand Alone
Power Cable
CANBus
Connector
Andere Handbücher für UC4+
41
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Norac Steuerungssystem Handbücher
Norac
Norac UC4 Plus Rogator 64 Series Bedienungsanleitung
Norac
Norac UC5 CANbus Bedienungsanleitung
Norac
Norac UC5 MAX Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC4 Plus Rogator 64 Series Bedienungsanleitung
Norac
Norac UC4+ Apache 1010 2005+ Bedienungsanleitung
Norac
Norac John Deere 4720 Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac Rogator 700 Series Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac Case 44 Series Bedienungsanleitung
Norac
Norac UC5 Rogator 600 Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Kurzanleitung
