Novexx Solutions AP 4.4 Bedienungsanleitung
11/08 Rev. 5.01-01 USER MANUAL
AP 4.4 – AP 5.4
Maintenance and Cleaning
General Notice .............................................. 2
Maintenance by Qualified Personnel ........ 2
Safety ........................................................ 2
Troubleshooting ........................................ 2
Ordering Spare Parts ................................ 3
Note on Cleaning ...................................... 3
Cleaning Agents ........................................ 3
Printhead .......................................................5
Cleaning the Printhead ..............................5
Changing the Printhead .............................7
Print Roller .....................................................8
Cleaning the Print Roller ............................8
Changing the Print Roller ...........................8
Punch Sensor ..............................................10
Index ............................................................11
11/08 Rev. 5.01-01 USER MANUAL Maintenance & Cleaning
AP 4.4 – AP 5.4
2
General Notice
Maintenance by Qualified Personnel
Regular technical maintenance is required to ensure that the device is always
in operating order.
Qualifications Maintenance work should only be carried out by qualified personnel. The
safety, reliability and longevity of the device depend on correct maintenance.
¯Persons causing damage as a result of unqualified maintenance, repair
and care are liable for these costs.
Manufacturer
Service For reliable maintenance, servicing, diagnosis and troubleshooting, please
contact your supplier, nearest dealer or another service supplier authorized
by the manufacturer.
Safety
Troubleshooting
Status If device malfunctions occur, analyze the device messages first. Please read
the relevant chapter contained in this documentation.
Calling for
Service If you are not authorized to carry out a diagnosis and repair of problems, plea-
se call your technician or authorized service supplier. The service personnel
have the required information and replacement parts to correctly carry out the
repairs.
WARNING!
Maintenance and cleaning may result in hazardous situations. Accidents can
occur by mechanical or electrical means if safety instructions are not ob-
served!
«Turn off the device and remove from the power supply prior to cleaning or
maintenance work!
«On no account should liquid be allowed to enter the device!
«Do not use any of kind of spray directly on the printer! Moisten a cloth with a
cleaning agent to clean the device!
«Repairs to the printer may only be carried out by a trained service technician!
11/08 Rev. 5.01-01 USER MANUAL Maintenance & Cleaning
AP 4.4 – AP 5.4
3
Ordering Spare Parts
The following information is required when ordering spare parts:
Order Specifi-
cations •Model
•Device serial number
•Optional device configuration
•Description and part number of the spare part
•Number of parts required
Note on Cleaning
Frequency of
Care Frequent maintenance and cleaning is required to ensure that the device
operates safely and provides a high level of performance. The frequency with
which maintenance checks are required depends on operating and environ-
mental conditions, the length of operation daily, and the print media used.
¯In particular, the printhead and feed roller need to be checked regularly
for paper, adhesives and ink residues.
Cleaning Agents
Dirty component Cleaning agent Order number
Dirty component Cleaning agent Order number
CAUTION! - Using parts that do not meet the manufacturer’s high
standards may damage the machine.
«Only use original spare parts supplied by the manufacturer.
Dirty component Cleaning agent Order number
Printhead Printhead Cleaning pen
(Fig. [1])
Cleaning paper
95327
5030
Print roller and other rubber
rollers
Roller cleaner
(Fig. [2])
98925
Metal deflection axis or
-guide tube
Cleaning fuel
Label remover A103198
External parts Common neutral cleaning
liquid
[Tab. 1] Recommended cleaning agents.
CAUTION! - Keep to the following rules to avoid damaging the device:
«Do not use any cleaning agent that could damage or destroy the resin sur-
face, labelling, display, nameplates, electrical components, etc.
«Do not use any cleaning agents that are abrasive or damaging to plastics.
Avoid acid or alkaline solutions.
11/08 Rev. 5.01-01 USER MANUAL Maintenance & Cleaning
AP 4.4 – AP 5.4
4
[1] Printhead cleaning pen (left) and roller cleaner (right).
11/08 Rev. 5.01-01 USER MANUAL Maintenance & Cleaning
AP 4.4 – AP 5.4
5
Printhead
¯If you do not have any professional
ESD protection equipment (ESD wrist-
band, ESD shoes, …), please place one
hand on an earthed object near to you (e.g.
tap or radiator) before touching the device
to discharge any static charge your body
may be carrying.
¯Clean printhead regularly to ensure op-
timal print head condition. It is recommen-
ded this is done when replacing the roll of
foil, using cleaning paper (article no. 5030).
Cleaning the Printhead
Impurities such as lint and color particles
from the thermotransfer foil may collect on
the printhead during printing. This can lead
to a noticeable detrimental effect on the
printed image, shown by:
•Differing contrast on the labels
•Light stripes in the printing direction
How to clean the printhead:
1. Switch off the printer.
2. Open the printhead pressure lever. The
printhead folds upwards.
3. Remove material and foil from the printer.
Cleaning with the cleaning pen
4. Applying light pressure, go over the
thermotransfer printhead (1) a few times
with the cleaning pen (Fig. 1).
CAUTION! - Electrostatic discharge
(ESD) or contact with sharp objects
may damage the printhead!
«Protect the printhead from electrostatic
discharges when performing mainte-
nance work or cleaning!
«Please try to keep bare hands away
from the thermotransfer printhead (1)
as much as possible!
«Do not allow sharp objects to come into
contact with the thermotransfer prin-
thead!
1
11/08 Rev. 5.01-01 USER MANUAL Maintenance & Cleaning
AP 4.4 – AP 5.4
6
Cleaning with the cleaning paper
1. Cut a strip of cleaning paper matching the
printhead width.
2. Insert the cleaning paper (2) into the prin-
ter with the rough side facing upwards
(Fig. 2).
3. Close the pressure lever.
4. Move the cleaning paper back and forth
repeatedly (Fig. 3).
Cleaning with alcohol-based solvents
¯Only use alcohol-based solvents
(ethanol) when the other two cleaning
agents are not available!
«Moisten a lint-free cloth with the solvent;
wipe the thermotransfer printhead with the
cloth.
CAUTION! - Alcohol-based
solvents are flammable!
«Observe the safety instructions
when handling flammable liquids.
«Don´t smoke.
2
3
11/08 Rev. 5.01-01 USER MANUAL Maintenance & Cleaning
AP 4.4 – AP 5.4
7
Changing the Printhead
Fig. 1: Printhead (1) with bracket (2).
Dismantling the printhead:
1. Switch off the printer and disconnect from
the power.
2. Remove material and foil from the printer.
3. Close the pressure lever (1).
4. Remove the knurled screws (2) (Fig. 1).
5. Open the pressure lever.
The printhead is released from the fastener
and remains on the print roller (Fig. 2).
6. Remove both printhead cables from the
printhead (Fig. 3).
The printhead has been dismantled.
Fitting the printhead:
1. Note the resistance of the new printhead.
You can read this on a sticker directly on
the printhead!
2. Affix the printhead cable.
3. Press the printhead against the fastener
from below and tighten the knurled
screws.
4. Call up the parameter SYSTEM PARA-
METERS > Head resistance and enter the
printhead resistance you noted earlier.
CAUTION! - Printhead (1) and brak-
ket (2) were adjusted exactly by me-
ans of special positioning tools.
«Don´t loosen the screws (3) fixing
the printhead on the bracket.
1
2
3
4
11/08 Rev. 5.01-01 USER MANUAL Maintenance & Cleaning
AP 4.4 – AP 5.4
8
Print Roller
Cleaning the Print Roller
Contamination on the print roller can de-
grade the quality of the print and the trans-
port of the material.
1. Switch off the printer and disconnect from
the power
2. Remove material and foil from the printer.
¯You can access the print roller more ea-
sily if you remove the tear-off edge (1) be-
forehand.
3. To do this, unfasten the screw (2) in the
middle of the tear-off edge (Fig. 2). You
need a size 10 Torx screwdriver for this.
Now remove the tear-off edge.
4. Moisten a lint-free cloth with roller cleaner
and wipe the printer roller (Fig. 3). Gra-
dually rotate the roller until it is completely
clean.
5. Refit the tear-off edge.
Changing the Print Roller
Tools
Size 10 Torx screwdriver (comes with the
printer).
Disassembly:
1. Switch off the printer and disconnect from
the power.
2. Remove material and foil from the printer.
3. Unfasten the screw (1) in the middle of the
tear-off edge (Fig. 1).
4. Remove the tear-off edge.
5. Release the set screw (2).
6. Remove the print roller sideways (Fig. 3).
Fitting:
1. Push the print roller through the external
bearing plate (3).
The printer roller axle is flattened on the
end.
1
2
3
11/08 Rev. 5.01-01 USER MANUAL Maintenance & Cleaning
AP 4.4 – AP 5.4
9
2. Place the axle in the socket (4) and gently
rotate until the flat part of the axle is under
the set screw (2).
3. Press the print roller firmly into the socket.
¯Plate (5) and bearing plate (3) must
lock flush with the interior (Fig. 4)!
4. Fasten the set screw.
1
2
3
4
11/08 Rev. 5.01-01 USER MANUAL Maintenance & Cleaning
AP 4.4 – AP 5.4
10
Punch Sensor
During printing the punch sensor can beco-
me contaminated with lint. Large amounts
of dirt can lead to problems with perforation
recognition.
To free the punch sensor from dust and ab-
raded particles:
1. Remove the cover (1) gently and swivel
downwards (Fig. 1).
2. Remove the sensor arm (2) (Fig. 2).
3. Clean the opening (3) with compressed
air.
¯The transmission sensor is situated in
the upper and the lower part of the sensor
arm on a level with the indicator (4). You
can find the reflex sensor about 5 mm fur-
ther out in the lower part.
CAUTION! - The sensor surface is
very sensitive to scratches!
«Do not use sharp objects or sol-
vents when cleaning the sensors.
1
2
Andere Handbücher für AP 4.4
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Novexx Solutions Drucker Handbücher
Novexx Solutions
Novexx Solutions 64- series Fehlerbehebungshandbuch
Novexx Solutions
Novexx Solutions EIDOS XTO2ce Bedienungsanleitung
Novexx Solutions
Novexx Solutions LTSI Bedienungsanleitung
Novexx Solutions
Novexx Solutions U-RX Bedienungsanleitung
Novexx Solutions
Novexx Solutions ALS 30 Series Bedienungsanleitung
Novexx Solutions
Novexx Solutions LA-BO Bedienungsanleitung
Novexx Solutions
Novexx Solutions ALX 73 Series Bedienungsanleitung
Novexx Solutions
Novexx Solutions 64- series Bedienungsanleitung
Novexx Solutions
Novexx Solutions TTX 350 Ocelot Bedienungsanleitung
Novexx Solutions
Novexx Solutions ALX 73 Series Bedienungsanleitung
Novexx Solutions
Novexx Solutions 64- series Bedienungsanleitung
Novexx Solutions
Novexx Solutions 64- series Bedienungsanleitung
Novexx Solutions
Novexx Solutions AP 5.4 Bedienungsanleitung
Novexx Solutions
Novexx Solutions ALX 73 Series Bedienungsanleitung
Novexx Solutions
Novexx Solutions 64- series Bedienungsanleitung
Novexx Solutions
Novexx Solutions ALX 92 Series Bedienungsanleitung
Novexx Solutions
Novexx Solutions ALS 104 Bedienungsanleitung
Novexx Solutions
Novexx Solutions ALX 73 Series Bedienungsanleitung
Novexx Solutions
Novexx Solutions ALX 73 Series Bedienungsanleitung
Novexx Solutions
Novexx Solutions AP 5.4 Bedienungsanleitung
