NXP Semiconductors Freescale Semiconductor MPC8308 Bedienungsanleitung

This document details all known silicon errata for the MPC8308. The following table provides a revision history for

this document.

Table 1. Document Revision History

Revision Date Significant Changes

5 09/2015 Added the following errata:

• eSDHC A-005055 and A-009204

• IEEE1588 A-007734

• PCIe PEX5

• USB A-003845

Added IEEE 1588_19 to Table 3, Summary of Silicon Errata and Applicable Revision.

Modified eTSEC69.

Renamed eTSEC-A002 to A-006502 and modified the write-up.

Renamed "PEX" heading to "PCIe".

Re-ordered the USB errata numerically.

407/2013 Renamed USB38 to USB erratum A-003817

Added the following errata:

• USB errata: A-003837, A-003827, A-003829

• eSDHC erratum: A-004577

Removed erratum DDR20

3 05/2012 • In Table 2, added silicon revision 1.1 SVR and PVR information.

• In Table 3, added silicon revision 1.1 column.

• In Table 3, updated the projected solution for the following errata: IEEE1588-A001,

PCIe- A002, and A-003985.

2 12/2011 • Added eLBC-A002

• Removed eLBC1, eLBC2, eTSEC29, IEEE1588_8, USB21

1 11/2011 • Added USB-A005, USB-A007, CPU-A022, PCIe-A002, A-003985

• Removed SPI6

• Updated USB-A001

0 07/2010 Initial release

Freescale Semiconductor MPC8308CE

Chip Errata Rev. 5, 09/2015

MPC8308 Chip Errata

The following table provides a cross-reference to match the revision code in the processor version register to the

revision level marked on the device.

Table 2. Revision Level to Part Marking Cross-Reference

Part Revision Processor Version Register

Value

System Version Register Value Mask

MPC8308 1.1 8085_0020 8101_0111 M17Y

MPC8308 1.0 8085_0020 8101_0110 M17Y

Table 3 summarizes all known errata.

Table 3. Summary of Silicon Errata and Applicable Revision

Errata Name Projected Solution Silicon Rev.

1.0 1.1

CPU

CPU6 DTLB LRU logic does not function correctly No plans to fix Yes Yes

CPU-A002 CPU may hang after load from cache-inhibited, unguarded

memory

No plans to fix Yes Yes

CPU-A022 The e300 core may hang while using critical interrupt No plans to fix Yes Yes

DDR

DDR21 MCK/MCK AC differential crosspoint voltage outside JEDEC

specifications

No plans to fix Yes Yes

DDR23 DDR read failure due to tDISKEW spec violation No plans to fix Yes Yes

eLBC

eLBC5 LTEATR and LTEAR may show incorrect values under certain

scenarios

No plans to fix Yes Yes

eLBC-A001 Simultaneous FCM and GPCM or UPM operation may

erroneously trigger bus monitor timeout

No plans to fix Yes Yes

eLBC-A002 Core may hang while booting from NAND using FCM No plans to fix Yes Yes

eSDHC

eSDHC16 Manual Asynchronous CMD12 abort operation causes protocol

violations

No plans to fix Yes Yes

eSDHC23 CMD CRC error or CMD index error may be set for CMD

without data while CMD with data is in progress

No plans to fix Yes Yes

eSDHC-A002 BLKATTR[BLKCNT] does not return to 0 after Transfer

Complete for multi-block transfer

No plans to fix Yes Yes

A-004577 PRSSTAT[DLA] bit does not reflect the data line state when any

command with busy (R1b) is issued

No plans to fix Yes Yes

A-005055 A glitch is generated on the card clock with software reset or a

clock divider change

No plans to fix Yes Yes

Table continues on the next page...

MPC8308 Chip Errata, Rev. 5, 09/2015

2 Freescale Semiconductor, Inc.

Table 3. Summary of Silicon Errata and Applicable Revision (continued)

Errata Name Projected Solution Silicon Rev.

1.0 1.1

A-009204 System bus may hang if software register SYSCTL[RSTD] is set

while DMA transactions are active

No plans to fix Yes Yes

eTSEC

eTSEC42 Frame is dropped with collision and HALFDUP[Excess Defer] =

No plans to fix Yes Yes

eTSEC58 VLAN Insertion corrupts frame if user-defined Tx preamble

enabled

No plans to fix Yes Yes

eTSEC59 False parity error at Tx startup No plans to fix Yes Yes

eTSEC64 User-defined Tx preamble incompatible with Tx Checksum No plans to fix Yes Yes

eTSEC67 ECNTRL[AUTOZ] not guaranteed if reading MIB counters with

software

No plans to fix Yes Yes

eTSEC68 Half-duplex collision on FCS of Short Frame may cause Tx

lockup

Documentation

update

Yes Yes

eTSEC69 Ethernet controller does not exit from Magic Packet mode when

an oddly formed Magic Packet is received

No plans to fix Yes Yes

eTSEC70 MAC: Malformed Magic Packet Triggers Magic Packet Exit No plans to fix Yes Yes

eTSEC71 The value of TSEC_ID2 is incorrect No plans to fix Yes Yes

eTSEC73 TxBD polling loop latency is 1024 bit-times instead of 512 No plans to fix Yes Yes

eTSEC74 MAC: Rx frames of length MAXFRM or MAXFRM-1 are marked

as truncated

No plans to fix Yes Yes

eTSEC75 Misfiled Packets Due to Incorrect Rx Filer Set Mask Rollback No plans to fix Yes Yes

eTSEC76 Excess delays when transmitting TOE=1 large frames No plans to fix Yes Yes

eTSEC78 Controller may not be able to transmit pause frame during

pause state

No plans to fix Yes Yes

eTSEC-A001 MAC: Pause time may be shorter than specified if transmit in

progress

No plans to fix Yes Yes

A-006502 Incomplete GRS or invalid parser state after receiving a 1- or 2-

byte frame

No plans to fix Yes Yes

IEEE 1588

IEEE 1588_14 TxPAL timestamp uses TxBD snoop enable instead of Tx data No plans to fix Yes Yes

IEEE 1588_16 Odd prescale values not supported No plans to fix Yes Yes

IEEE 1588_17 Cannot use inverted 1588 reference clock when selecting

eTSEC system clock as source

No plans to fix Yes Yes

IEEE 1588_19 Tx FIFO data parity error (DPE) may corrupt Tx timestamps if

TMR_CTRL[TRTPE]=1

No plans to fix Yes Yes

IEEE 1588_20 eTSEC 1588: Write to reserved 1588 register space causes

system hang

No plans to fix Yes Yes

IEEE1588-A001 Incorrect received timestamp or dropped packet when 1588

time-stamping is enabled

Fixed in Rev 1.1 Yes No

A-007734 Stale time stamps and over-flow conditions can occur when

using an external 1588 input clock at certain frequencies

No plans to fix Yes Yes

General

Table continues on the next page...

MPC8308 Chip Errata, Rev. 5, 09/2015

Freescale Semiconductor, Inc. 3

Table 3. Summary of Silicon Errata and Applicable Revision (continued)

Errata Name Projected Solution Silicon Rev.

1.0 1.1

General14 Electrostatic Discharge (ESD) may fail to meet the 2KV Human

body body model (HBM)

No plans to fix Yes Yes

General16 Enabling I2C could cause I2C bus freeze when other I2C devices

communicate

No plans to fix Yes Yes

General17 DUART: Break detection triggered multiple times for a single

break assertion

No plans to fix Yes Yes

PCIe

PEX1 No support of PCI Express completions with BCM bit set (PCIX

bridge interface)

No plans to fix Yes Yes

PEX2 DMA Interrupt descriptor race condition (IDRC) No plans to fix Yes Yes

PEX5 PCI Express LTSSM may fail to properly train with a link partner

following HRESET#

No plans to fix Yes Yes

PEX7 Recovery from hot reset or link down No plans to fix Yes Yes

PCIe-A002 PCI Express Packets may be transmitted with excess data on

x1 link

Partially fixed in 1.1 Yes No

RTC

A-003985 Real Time Counter Register (RTCTR) may not work correctly Fixed in Rev 1.1 Yes No

USB

USB15 Read of PERIODICLISTBASE after successive writes may

return a wrong value in host mode

No plans to fix Yes Yes

USB19 USBDR in Host mode does not generate an interrupt upon

detection of a CRC16/PID/Timeout error when a received IN

data packet is corrupted

No plans to fix Yes Yes

USB25 In host mode, when the software forces a port resume by writing

into the FPR bit of the portsc register, the port change detect

interrupt bit is falsely fired

No plans to fix Yes Yes

USB26 NackCnt field is not decremented when received NYET during

FS/LS Bulk/Interrupt mode

No plans to fix Yes Yes

USB27 When an ACK or NAK is sent from the device in response to a

PING, the CERR counter value is not being reset to the initial

value

No plans to fix Yes Yes

USB28 In device mode, when receiving a Token OUT, if a Rx flush

command is issued at the same time, to the same endpoint, the

packet will be lost

No plans to fix Yes Yes

USB29 Priming ISO over SOF will cause transmitting bad packet with

correct CRC

No plans to fix Yes Yes

USB31 Transmit data loss based on bus latency No plans to fix Yes Yes

USB32 Missing SOFs and false babble error due to Rx FIFO overflow No plans to fix Yes Yes

USB33 No error interrupt and no status will be generated due to ISO

mult3 fulfillment error

No plans to fix Yes Yes

USB34 NAK counter decremented after receiving a NYET from device No plans to fix Yes Yes

USB35 Core device fails when it receives two OUT transactions in a

short time

No plans to fix Yes Yes

USB36 CRC not inverted when host under-runs on OUT transactions No plans to fix Yes Yes

Table continues on the next page...

MPC8308 Chip Errata, Rev. 5, 09/2015

4 Freescale Semiconductor, Inc.

Table 3. Summary of Silicon Errata and Applicable Revision (continued)

Errata Name Projected Solution Silicon Rev.

1.0 1.1

USB37 OTG Controller as Host does not support Data-line Pulsing

Session Request Protocol

No plans to fix Yes Yes

USB-A001 Last read of the current dTD done after USB interrupt No plans to fix Yes Yes

USB-A002 Device does not respond to INs after receiving corrupted

handshake from previous IN transaction

No plans to fix Yes Yes

USB-A003 Illegal NOPID TX CMD issued by USB controller with ULPI

interface

No plans to fix Yes Yes

USB-A005 ULPI Viewport not Working for Read or Write Commands With

Extended Address

No plans to fix Yes Yes

USB-A007 Host controller fails to enter the PING state on timeout during

High Speed Bulk OUT/DATA transaction

No plans to fix Yes Yes

A-003817 USB Controller locks after Test mode "Test_K" is completed No plans to fix Yes Yes

A-003827 DATA PID error interrupt issued twice for the same high

bandwidth ISO transfer

No plans to fix Yes Yes

A-003829 Host detects frame babble but does not halt the port or generate

an interrupt

No plans to fix Yes Yes

A-003837 When operating in test mode, the CSC bit does not get set to 1

to indicate a change on CCS

No plans to fix Yes Yes

A-003845 Frame scheduling robustness-Host may issue token too close to

uframe boundary

No plans to fix Yes Yes

MPC8308 Chip Errata, Rev. 5, 09/2015

Freescale Semiconductor, Inc. 5

CPU6: DTLB LRU logic does not function correctly

Description: The DTLB is implemented as 2-way set associative with 32 entries per way. EA[15:19] is used

to determine which one of the 32 entries of both ways. When a DTLB miss occurs, normally

the CPU provides information (through SRR1 bit 14, DTLB replacement way) to indicate which

of the two ways the software (DTLB exception handler or the software table walk routine)

should use to bring in the new page. Presumably, the CPU provides the information, through

SRR1 bit 14, based on the LRU (least recently used) algorithm. However, because of this bug,

this is not the case.

In fact, for any given EA[15:19], when a DTLB miss occurs, SRR1 bit 14 always indicates that

way1 should be used or replaced. (Except if it is the very first DTLB miss after hard reset. In

this case, SRR1 bit 14 indicates way0 should be used.)

In other words, if the DTLB exception routine follows the SRR1 bit 14's suggestion to do the

TLB replacement, it always replaces the one in way1. In addition, whatever has been loaded in

way0 is effectively locked and is not replaced.

Impact: Performance degradation due to the reduction of usable DTLB entries.

Workaround: In the software, use one word (32 bits) to keep the record of the DTLB way that is Least

Recently Written (LRW). Use this information to overwrite the SRR1 bit 14 (DTLB replacement

way) when a Data Translation Miss exception occurs. Basically, the LRU (least recently used)

hardware algorithm is changed to an LRW (least recently written) software algorithm.

For the system that has no secondary storage (such as a hard drive), it is highly recommended

to set the C (Change) bit during the DTLB load exception to optimize the performance.

For a system that has a secondary storage and the OS does a page swap, the OS can choose

whether to set the C bit in the DTLB load exception.

If the C bit is set in the DTLB load exception, it can preempt the subsequent DTLB store

exception to the same page. However, since all the pages are marked as changed, during the

page swap all pages must be written back to the secondary storage regardless of whether they

have really been changed or not.

If the C bit is not set in the DTLB load exception with the LRW algorithm, a subsequent store to

the same page as the previous load will use a separate entry. Therefore, one page occupies

both ways. This causes inefficiency for the DTLB allocation but may save time during the page

swap since the page change status is correctly marked.

Fix plan: No plans to fix

MPC8308 Chip Errata, Rev. 5, 09/2015

6 Freescale Semiconductor, Inc.

CPU-A002: CPU may hang after load from cache-inhibited, unguarded memory

Description: There is a one-core-clock-cycle window of opportunity for a snoop to collide with the data

returned from cache-inhibited memory to a load that has been cancelled. This collision can

hang the data cache in a busy state, prohibiting further data cache accesses. The snoop

address is immaterial.

The load can be cancelled if it meets the following conditions: it was executing speculatively

beyond a conditional branch that resolved unfavorably or was pre-empted by an external

interrupt or decrementer interrupt that took priority. The load must be from a cache-inhibited,

non-guarded memory block. A load from cacheable memory, even if it misses in the cache,

does not hang the data cache in a busy state, and if the memory block is marked guarded, the

load will not be executed out of order.

An external master must put addresses on the bus with the attribute of memory coherency

required (Global) so that the CPU allows snooping of the data cache. External masters have to

be programmed to snoop.

Impact: CPU halts or stops executing on a subsequent load or store that finds the data cache busy.

This load or store does not complete, and the data cache stays busy until a hardware or

software reset (HRESET or SRESET). Debug tools will reveal that the program counter is

stopped and pointing to the load or store that cannot complete.

Workaround: Use one of the following options:

• Set bit 14 in the HID2 register. This bit disables a minor feature that attempted to take

advantage of cache hits under a cancelled cache miss which was still waiting for data.

There should be no performance loss from disabling this feature. HID2[14] is not

implemented on any other e300 devices. Setting it will have no effect on other devices or

any future revisions.

• Mark all data memory blocks from which loads could occur “cacheable” or “guarded.”

Fix plan: No plans to fix

MPC8308 Chip Errata, Rev. 5, 09/2015

Freescale Semiconductor, Inc. 7

CPU-A022: The e300 core may hang while using critical interrupt

Description: If BOTH critical interrupt AND normal interrupt types are used in a system, the e300 core may

hang.

Impact: The processor may stop dispatching instructions until a hardware reset(HRESET). Debug tools

will not be able to read any register correctly except program counter IAR which points to a

location in the critical interrupt vector.

Workaround: If both critical interrupt and normal interrupt types are used, then instead of using an rfi

instruction at the end of every exception handler, replace the rfi with the following:

1. Disable critical interrupts by setting MSR[CE] to 0 with a mtspr instruction.

2. Copy SRR0 and SRR1 to CSRR0 and CSRR1, respectively.

3. Execute an rfci instruction. This enables MSR[CE] and any other bits that the original rfi

would have set including the MSR[EE].

Sample Code:

// Disable MSR[CE]

mfmsr r2

lis r3, 0xffff

ori r3, r3, 0xff7f

and r2, r2, r3

sync

mtmsr r2

isync

// Copy SRR0, SRR1 to CSRR0 and CSRR1

mfspr r2, srr0

mfspr r3, srr1

mtspr csrr0, r2

mtspr csrr1, r3

...restore GPRs

rfci

Fix plan: No plans to fix

MPC8308 Chip Errata, Rev. 5, 09/2015

8 Freescale Semiconductor, Inc.

DDR21: MCK/MCK AC differential crosspoint voltage outside JEDEC specifications

Description: The crossover points of the MCK and MCK signals of the DDR controller are not meeting

JESD79-2C specifications, which indicates that the crossover points should lie within ±125 mV

range of reference voltage.

Impact: Disagreement with the JESD79-2C standard.

Workaround: To meet the JESD79-2C crosspoint voltage specifications, we recommend implementing the

following connections between the DDR controller and DDR2 memory:

Figure 1. Recommended connections for DDR controller and memory

Effect of different circuit components on MCK and MCK signals:

1. Increasing R2 and R3 shifts signal levels up (used as pull up).

2. Increasing C1 increases rise/fall time of mck signal.

3. Increasing C2 increases rise/fall time of mckb signal.

4. Reducing R1 can help in shifting the signals up.

5. R4 and R5 can be used to make termination proper.

Component Placing:

R4, R5, C1, C2 near to SOC, R1, R2, and R3 have been placed at the end of clock

transmission lines.

By considering these suggestions and choosing proper values of components for a particular

board layout, one can keep crossover points within range.

We recommend varying termination resistor R1 first. Lowering R1 can help increase the

voltage levels up. The only disadvantage is that it may add up more reflections. Therefore, the

user must decide accordingly. If it does not give sufficient margin, the user can add the pull-up

resistor (R3 and R4) option to further increase the voltage levels.

MPC8308 Chip Errata, Rev. 5, 09/2015

Freescale Semiconductor, Inc. 9

Exact values of components vary from design to design and some of them may not be required

fpr all designs. We recommend that you make provisions for all these options in your design.

Fix plan: No plans to fix

MPC8308 Chip Errata, Rev. 5, 09/2015

10 Freescale Semiconductor, Inc.

Andere NXP Semiconductors Mikrocontroller Handbücher

NXP Semiconductors

NXP Semiconductors FRDM-KW41Z Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors JN517x-DK005 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MPC5606S Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors IOTZTB-DK006 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM-SE051ARD Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors QN9020 mini DK Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MPC5777M Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors S12ZVML-MINIKIT Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN7462AU Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors S32K1 Series Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors FRDM665SPIEVB Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors ColdFire MCF52235 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors USB-KW38 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC1102 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors EasyEVSE EV Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale TWR-K60D100M Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors SAFE ASSURE Qorivva MPC5602P Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors Harpoon Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MPC574xR Series Montage- und Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors UM10883 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors i.MX31 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC5410x Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MC9S08SU16 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MC9S08QL8 MCU Series Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung