OHAUS Defender T24PE Bedienungsanleitung

RS232 Interface

Instruction Manual

for T24PE Indicators

Interfase RS232

Manual de instrucciones

para indicadores T24PE

Interface RS232

Manuel d’instructions

pour les indicateurs T24PE

RS232 Schnittstelle

Bedienungsanleitung

für T24PE Anzeigen

Interfaccia RS232

Manuale di istruzioni

Per indicatori T24PE

RS232 Interface EN-1

INTRODUCTION

This RS232 kit is for use with the T24PE Indicators.

KIT CONTENTS

RS232 PCB

RS232 Interface Cable

Screws (1)

Instruction Manual

INTERFACE INSTALLATION

CAUTION: Observe the following precautionary measures to avoid

personal injury or damage to the equipment.

- Disconnect the equipment from the mains power supply and internal battery before beginning

the installation process.

- Use electrostatic protection measures when handling the printed circuit boards.

- Installation should only be performed by qualified personnel.

1. Disconnect the power supply and load cell cables from the indicator.

2. Remove the 4 screws on the bottom of the indicator and open the enclosure.

3. Remove the plastic cover by pushing it out with a screwdriver or similar object.

EN-2 RS232 Interface

4. Connect the RS232 Interface Cable as below.

5. Secure the RS232 PCB to the main board with the screw and connect the RS232 cable to the

RS232 PCB.

6. Assemble the top and bottom enclosure using the four screws.

7. Connect the load cell and power supply cables to the indicator.

RS232 Interface EN-3

SETUP

Upon installation, the print sub-menu will be visible.

Reset No, Yes

Baud Rate: 300, 600, 1200, 2400, 4800, 9600, 19200

Parity: 7 Even, 7 Odd, 7 None, 8 None

Stop Bit 1or 2

Handshake: Off, XON/XOFF

Stable Only Off, On

Auto Print Off

On Stable (-> Load, Load and Zero),

Interval (-> 1…3600),

Continuous

Content Result (->Off, On, NUM)

Gross (->Off, On)

Net (->Off, On)

Tare (->Off, On)

Unit (->Off, On)

Mode (->Off, On)

Info (->Off, On)

Layout Format (->Multiple, Single) Feed (->Line Feed, 4 Line Feed, Form Feed)

End Print Exit PRINT menu

Note: For more detailed information, see section 3.8 in the T24PE instruction manual.

OPERATION

Output

With the interface installed the scale will operate in one of the following two ways:

Auto Print = off, Stable = on or off

Pressing PRINT will send the display data. If Stable is set to On, the balance will wait for a

stable reading before sending data.

Auto Print = not off, Stable = on or off

The scale will automatically send data based on the settings in the Menu. If Stable is set to On,

only stable will be sent.

Data sent is in standard ASCII format terminated with a [CRLF] (carriage return-line feed).

[weight] 11 characters

[space] 1 character

[unit] 5 characters max (left justified)

[space] 1 character

[stability] 1 character “?” when unstable, blank when stable

[space] 1 character

[G/N] 1 character

[Term. Char(s)]

EN-4 RS232 Interface

Input

The scale will respond to various commands sent via the interface.

Command

Legacy Command (2)

Function

Immediate Print of displayed weight (stable or unstable).

Print displayed weight (stable or unstable).

Continuous Print.

Print on Stability.

0S: Turn off “Stable Only” menu item and allow unstable

print. 1S: Turn on “Stable Only” menu item and only print

stable print.

Interval Print x = Print Interval (1-3600 sec), 0P turns auto

print OFF

Same as pressing Zero Key

Same as pressing Tare Key.

Download Tare value in grams (positive values only).

Sending 0T clears tare (if allowed).

Print current unit: g, kg, lb, PCS

Set scale to unit x: 1=g, 2=kg, 3=lb,

Set scale to mode x. M will scroll to next enabled mode.

Version: print name, software revision

\EscR

Global reset to reset all menu settings to the original

factory defaults

Notes:

The second commands listed are “legacy’ commands,

which maintain compatibility with older products.

Auto-Print Operation

Once Auto-Print is activated in the menu, the balance will send data as required. To temporarily stop

Auto-Printing, press the PRINT key. If there is data in the print buffer the printer will finish printing this

data. A second press will resume Auto-Printing.

(Note: In some modes, stopping or resuming Auto-Print must be done when the balance is not

reading “0”.)

ACCESSORIES

For a complete listing of OHAUS printers and other accessories, contact OHAUS Corporation or visit

www.OHAUS.com

RS232 Interface EN-5

COMPLIANCE

Disposal

In conformance with the European Directive 2002/96/EC on Waste Electrical and

Electronic Equipment (WEEE) this device may not be disposed of in domestic waste.

This also applies to countries outside the EU, per their specific requirements.

Please dispose of this product in accordance with local regulations at the collecting

point specified for electrical and electronic equipment. If you have any questions,

please contact the responsible authority or the distributor from which you purchased

this device.

Should this device be passed on to other parties (for private or professional use), the

content of this regulation must also be related.

For disposal instructions in Europe, refer to www.ohaus.com/weee

Thank you for your contribution to environmental protection.

Interfase RS232 ES-1

INTRODUCCIÓ N

Este kit RS232 es para uso en indicadores T24PE.

CONTENIDO DEL KIT

PLACA DE CIRCUITO RS232

Cable de interfase RS232

Tornillo (1)

Manual de instrucciones

INSTALACIÓ N DE LA INTERFASE

PRECAUCIÓ N: Observe las siguientes medidas cautelares para evitar

lesiones personales o dañ os al equipo.

- Desconecte el equipo de la red de alimentació n y batería interna antes de empezar el proceso de

instalació n.

- Utilizar medidas de protecció n electrostá tica al manejar los tableros del circuito impreso.

- La instalació n debe realizarse só lo por personal cualificado.

1. Desconecte la alimentació n elé ctrica y cables de la cé lula de carga del indicador.

2. Quite los 4 tornillos de la parte inferior del indicador y abra la carcasa.

3. Retire la tapa de plá stico, empujando hacia fuera con un destornillador u objeto similar.

ES-2 Interfase RS232

4. Conecte el cable de interfase RS232 como se muestra a continuació n.

5. Asegure la placa de circuito RS232 a la placa principal con el tornillo y conecte el cable RS232 a la

placa de circuito RS232.

6. Montar el recinto superior e inferior mediante los cuatro tornillos.

7. Conecte los cables de suministro carga celular y potencia el indicador.

Andere Handbücher für Defender T24PE

Inhaltsverzeichnis

Sprachen:

Andere OHAUS Messgerät Handbücher

OHAUS

OHAUS Defender i-DT61PW Bedienungsanleitung

OHAUS

OHAUS TD52P Bedienungsanleitung

OHAUS

OHAUS TD52 Bedienungsanleitung

OHAUS

OHAUS CKW-55 Bedienungsanleitung

OHAUS

OHAUS MB25 Bedienungsanleitung

OHAUS

OHAUS starter 3100 Bedienungsanleitung

OHAUS

OHAUS Defender 3000 Bedienungsanleitung

OHAUS

OHAUS a-AB33M1 Bedienungsanleitung

OHAUS

OHAUS MB35 Bedienungsanleitung

OHAUS

OHAUS TD52 Bedienungsanleitung

OHAUS

OHAUS STARTER 3100C Bedienungsanleitung

OHAUS

OHAUS STARTER 2200 Bedienungsanleitung

OHAUS

OHAUS MC2000 Bedienungsanleitung

OHAUS

OHAUS ST300-G Bedienungsanleitung

OHAUS

OHAUS T51 Gebrauchs- und Pflegehandbuch

OHAUS

OHAUS ST20D Bedienungsanleitung

OHAUS

OHAUS TD52 Bedienungsanleitung

OHAUS

OHAUS Ranger 3000 Series Bedienungsanleitung

OHAUS

OHAUS ST20D Bedienungsanleitung

OHAUS

OHAUS CD-1 Bedienungsanleitung

OHAUS

OHAUS starter 3100 Bedienungsanleitung

OHAUS

OHAUS MB90 Bedienungsanleitung

OHAUS

OHAUS ST400D-B Bedienungsanleitung

OHAUS

OHAUS Defender 6000 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung