OHAUS TD52 Bedienungsanleitung

TD52 Indicator

Discrete I/O Option

Instruction Manual

Interfaz E/S Discreta

Manual de instrucciones

Interface discrète I/O

Manuel d’instruction

Discrete I/O-Schnittstelle

Bedienungsanleitung

Modulo d’Interfaccia I/O

Manuale di Istruzioni

I/O 折

折ↅ

∎䞷広㢝󱂖

EN-1

INTRODUCTION

This discrete I/O interface Kit is for use with OHAUS TD52P and TD52XW indicators.

When installed, the system software allows the relay to be programmed in a variety of ways.

BASIC APPLICATIONS

Applications include driving external Over/Accept/Under displays, motor controls for semi-automatic

filling systems, sortingsystems, interfacingto industrial PLC systems, etc. The Relay outputs can also

be used as slave relays to drive high power relays in larger systems.

For the setup in each application, please refer to the instruction manual supplied with scale.

Set up the discrete I/O controls as described in the I/O menu section of that manual.

CAUTION: Read all safety warnings before installing, making connections, or servicing the

Discrete I/O PCB. Failure to comply with these warnings could result in personal injury

and/or property damage. Retain all instructions for future reference.

KIT CONTENTS

Screws (4)

Connector, 3 Pin

Cable Gland

I/O PCB

Cable to mainboard

Connector, 6 Pin

()

Conn

board

able

lan

(

)

ector, 3 P

e to main

ect

EN-2

INTERFACE INSTALLATION

CAUTION: THE INSTALLATION AND WIRE CONNECTIONS TO THE DISCRETE I/O

BOARD SHOULD ONLY BE DONE BY AUTHORIZED AND QUALIFIED

PERSONNEL, SUCH AS AN ELECTRICIAN.

WARNING: BEFORE MAKING CONNECTIONS TO THE RELAY TERMINALS,

POWER OFF THE SYSTEM AND REMOVE ALL EXTERNAL AC POWER

CONNECTIONS.

WARNING: WHEN MAKING ANY LINE VOLTAGE CONNECTIONS TO THE

DISCRETE I/O, FOLLOW NATIONAL ELECTRICAL CODE (NEC) OR LOCAL

AUTHORITY WIRING STANDARDS AND SAFETY PRACTICES.

For TD52P:

1. Separate the indicator from the base by loosening load cell cable male connector.

Remove the interface option cover.

2. Break off the rib of the accessory cover as shown.

Rib

Load cell cable male connector

Interface option cover

EN-3

3. Connect the cable to the main board connector 2 as shown. Place the ferrite in the slot of

the rear housing as shown.

4. Install the relay board. Secure it with the 2 screws. Connect the cable to the relay board

12 pin connector.

Cable

Ferrite

Main board

connector 2

12 Pin Connector

Screw

EN-4

5. Connect the relay cable to the 3 pin and 6 pin connectors. Fix the relay cable with the

nylon cable tie to avoid falling off from the terminal block.

6. Put the interface option cover back on the terminal.

For TD52XW:

1. Remove the interface option cover. Remove the 6 screws with sealed washers. Remove

the M25 hole plug as shown.

3 Pin / 6 Pin Connector

Nylon cable ties

Relay Cable

Screw

Load cell cable male

connector

M25 Hole plug

EN-5

2. Rotate the rear housing down away from the front housing as shown.

3. Connect the cable to the main board connector 2. Place the ferrite in the slot of the

internal cover as shown.

cable

Ferrite

Main board connector 2

EN-6

4. Disassemble the cable gland by loosening the cap nut and removing the rubber seal.

Pass the relay output through the cap nut, then spread the rubber seal and place it over

the cable. Now pass the cable through the body of the cable gland.

5. Install the relay board. Secure it with 2 screws. (Note: boss post is 5 and 7.)

Connect the cable to the relay board 12 pin connectors. Put the relay cable through the

M25 hole. Connect it to the 3 pin and 6 pin connectors.

Relay Output Cable

M25 Gland

Cap Nut

Boss Post 5, 7

EN-7

6. Put the rear housing back on the front housing. Re-install the 6 screws.

7. Fasten the M25 gland to the rear housing.

Screw

12Pin

Connector

3Pin / 6pin

Connector

Relay cable

M25 Gland

EN-8

8. Push the rubber seal into the M25 cable gland.

9. Fasten the cap nut of M25 gland.

For TD52XW with reversed rear cover:

1. Remove the interface option cover. Remove the 6 screws with sealed washer. Remove

the M25 hole plug as shown.

Rubber Seal

Cap nut of M25 gland

Screw

M25 hole plug

Load cell cable male connector

Andere Handbücher für TD52

Inhaltsverzeichnis

Sprachen:

Andere OHAUS Messgerät Handbücher

OHAUS

OHAUS ST300-G Bedienungsanleitung

OHAUS

OHAUS ST300 Bedienungsanleitung

OHAUS

OHAUS MB90 Bedienungsanleitung

OHAUS

OHAUS ST Series Bedienungsanleitung

OHAUS

OHAUS Ranger 3000 Series Bedienungsanleitung

OHAUS

OHAUS TD52 Bedienungsanleitung

OHAUS

OHAUS 5000 Bedienungsanleitung

OHAUS

OHAUS CKW Series Bedienungsanleitung

OHAUS

OHAUS ST20D Bedienungsanleitung

OHAUS

OHAUS a-AB33M1 Bedienungsanleitung

OHAUS

OHAUS AB23PH Bedienungsanleitung

OHAUS

OHAUS MB23 Bedienungsanleitung

OHAUS

OHAUS TD52 Bedienungsanleitung

OHAUS

OHAUS CKW Gebrauchs- und Pflegehandbuch

OHAUS

OHAUS STARTER 3100C Bedienungsanleitung

OHAUS

OHAUS i-DT61XWE Bedienungsanleitung

OHAUS

OHAUS MB90 Bedienungsanleitung

OHAUS

OHAUS ST300-B Bedienungsanleitung

OHAUS

OHAUS i-DT33P Bedienungsanleitung

OHAUS

OHAUS MB90 Bedienungsanleitung

OHAUS

OHAUS a-AP30TUR Bedienungsanleitung

OHAUS

OHAUS Defender 2000 Series Bedienungsanleitung

OHAUS

OHAUS MC2000 Bedienungsanleitung

OHAUS

OHAUS a-AB33EC Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung