OHAUS TD52 Bedienungsanleitung
TD52 Indicator
Analog Option
Instruction Manual
Kit Analógico
Manual de instrucciones
Kit Analogue
Manuel d’instruction
Analog-Kit
Bedienungsanleitung
Kit Analogico
Manuale di Istruzioni
模拟量选件
使用说明书
아날로그 키트는
사용설명서
ディフェンダー5000 シリーズ
アナログ キット
取扱説明書
Дополнительный интерфейс аналогового вывода для
весового терминала TD52
Руководство по эксплуатации
Manual_TD52_Analog_V1
EN-1
INTRODUCTION
This analog kit is for use with the Defender® 5000 TD52 indicators.
INTERFACE INSTALLATION
For TD52P:
1. Separate the indicator from the base by loosening load cell cable
male connector. Remove the interface option cover.
2. Break off the rib of the interface option cover as shown.
Load cell cable connector
Interface option cover
Rib
EN-2
3. Connect the 12-pin Cable Connector included with the kit to the
Main Board Connector 2. Place the ferrite in the slot of the rear
housing as shown.
4. Install the Analog Current Loop board in the indicator using 2 screws as
shown. Connect the 12 pin connector cable from the main board to the
Analog Current Loop board 12 pin connector.
5. Connect the current loop cable to the 3 pin and 3 pin connectors.
Ferrite
Main board connector
2
Cable
Screw
12 Pin connector
3 Pin / 3 Pin connector
Current Loop Cable
EN-3
In the direction of the arrow (from
the bottom up)
Description
Pin
V-
Negative voltage output
J2
V+
Positive voltage output
GND
Ground
I-
Negative current output
J3
I+
Positive current output
GND
Ground
6. Fix the cable with the cable tie to avoid falling off from the terminal
block. Put the Interface option cover back on the terminal.
For TD52XW:
1. Remove the interface option cover. Remove the 6 screws with sealed
washers. Remove the M25 hole plug as shown.
Nylon cable tie
Load cell cable connector
Screws
M25 Hole plug
EN-4
2. Rotate the rear housing down away from the front housing as
shown.
3. Connect the 12-pin Cable Connector included with the kit to the
Main Board Connector 2. Place the ferrite in the slot of the black
part as shown.
4. Disassemble the M25 Cable Gland by loosening the cap nut and removing
the rubber seal. Pass the Current Loop Output cable through the cap nut,
then spread the rubber seal and place it over the cable. Now pass the
cable through the body of the cable gland.
Main board connector 2
Ferrite
Cable
M25 Gland
Cap nut
4~20mA Current loop
output cable
EN-5
5. Install the relay board. Secure it with 2 screws to Boss Post 5 and
7 as shown.
Connect the 12 pin connector cable from the main board to the
Analog Current Loop board 12 pin connector.
6. Pass the Current Loop Output cable through the M25 hole.
Connect it to the 3 pin and 3 pin connector as shown below.
7. Put the rear housing back on the front housing. Re-install the 6
screws (Torque is 1.8N*m±0.5).
Boss post 5, 7
Screw
3 Pin / 3 Pin connector
12 Pin connector
Cable
Current Loop Cable
EN-6
8. Fasten the cap nut of M25 gland to the rear housing.
9. Warp the rubber seal onto the Current Loop Output cable and push
it to the hole.
10. Fasten the cap nut of M25 gland.
Cap nut of M25 gland
Rubber seal
EN-7
For TD52XW with reversed rear cover:
1. Remove the interface option cover. Remove the 6 screws with
sealed washer. Remove the M25 hole plug as shown.
2. Take the rear housing down from the front housing as shown.
Load cell cable connector
Screws
M25 Hole plug
EN-8
3. Connect the cable to the main board connector 2.
4. Disassemble the cable gland by loosening the cap nut and
removing the rubber seal. Pass the relay output through the cap
nut, then spread the rubber seal and place it over the cable. Now
pass the cable through the body of the cable gland.
Cable
M25 Gland
Cap nut
4~20mA Current loop
output cable
Main board connector 2
Andere Handbücher für TD52
7
Inhaltsverzeichnis
Sprachen:
Andere OHAUS Messgerät Handbücher
OHAUS
OHAUS TD52 Bedienungsanleitung
OHAUS
OHAUS TD52 Bedienungsanleitung
OHAUS
OHAUS i-DT33P Bedienungsanleitung
OHAUS
OHAUS D52 Bedienungsanleitung
OHAUS
OHAUS MC2000 Bedienungsanleitung
OHAUS
OHAUS MB35 Bedienungsanleitung
OHAUS
OHAUS starter 3100 Bedienungsanleitung
OHAUS
OHAUS a-AP30TUR Bedienungsanleitung
OHAUS
OHAUS STARTER 300C Bedienungsanleitung
OHAUS
OHAUS Defender 2000 Series Bedienungsanleitung
OHAUS
OHAUS 5000 Bedienungsanleitung
OHAUS
OHAUS MB35 Bedienungsanleitung
OHAUS
OHAUS 2000 Series Bedienungsanleitung
OHAUS
OHAUS STARTER 400D Bedienungsanleitung
OHAUS
OHAUS STARTER 2100 Bedienungsanleitung
OHAUS
OHAUS STARTER 300 Bedienungsanleitung
OHAUS
OHAUS TD52 Bedienungsanleitung
OHAUS
OHAUS STARTER 3100M Bedienungsanleitung
OHAUS
OHAUS T51XW Bedienungsanleitung
OHAUS
OHAUS MB45 Bedienungsanleitung
