Olympia electronics GR-292/M/HL Bedienungsanleitung

Page 1 from 6 923293007_09_001

GENERAL

This device is used indoors (ta 40 C) in places

where emergency luminaires are needed.

Each device must be permanently connected

to mains power supply. The GR-292/M/HL is

suitable for corridors lighting and the GR-

293/M/HL for open area lighting. In normal

operation the battery is charging. In case of a

mains power supply failure, the device enters

emergency mode and the illumination LED

turns on. When the mains power supply is

restored, the device turns to normal operation.

INSTALLATION

To install the luminaire follow the installation

instructions οn page 3.

Battery Charging

The battery charging is completely controlled.

In this case, is achieved the perfect battery

maintenance , as well as the elongation of its

duration. When the battery has completely

charged, it charges with a maintenance

current.

Battery Cut-off

The device enters this mode when the mains

power supply has failed and battery has lost its

energy. During this mode the device enters in

idle state and battery consumption is

negligible, in order to be protected from deep

discharge.

Manual Test

This test can be done by pushing the test

button. The light source and the emergency

circuit of the device are monitored. The manual

test can be conducted only if the main power

supply and the battery are connected. During

this test period all indication LEDs are OFF.

Automatic Operational Test

This test includes all the operations that provide

the manual test and is conducted automatically

every 15 days. In order to be performed, the

mains power supply and the battery should be

connected.

Automatic Autonomous Test

This test monitors the device’s back up

operation and emergency duration. The

BATTERY FAULT LED blinks during the test,

indicating this process to the user. This test is

conducted automatically every six months. In

order to be performed, the mains power supply

should be connected and the battery must be

fully charged. If the battery is not fully charged,

the test is postponed until the battery is

completely charged. If during this test, the

autonomy is less than the nominal then the

SELF TESTING NON-MAINTAINED EMERGENCY CEILING MOUNTED LUMINAIRES

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

CONSTRUCTION MATERIAL

EXTERNAL DIMENSION

WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERY (Ni-MH)

CHARGE TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

LIGHT SOURCE

220-240V AC / 50-60Hz

24 hours

Deep discharge and overcharge protection

IP20

4.8V/4Ah

1 white power LED

5 to 40 C

Up to 95%

ABS/PC

3 years (1 year for the battery)

737gr.

Ø125 x 72 mm

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

Charge, lamp fault, battery fault, TEST button

4.9W / 5.2 VA

TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 5)

Thank you for your trust in our products

Olympia Electronics - European manufacturer

3 hours

330lm

GR-292/M/HL GR-293/M/HL

battery fault led turns on continuously indicating

that the battery must be replaced.

Back Up Operation

The autonomous duration of battery during

emergency mode is at least the one that is

stated in the list of the technical characteristics.

During emergency mode, a light source test is

also performed.

Resetting Errors

Push the Test button for >10 seconds, to delete

all the indicated LED errors. Then the device

enters regular operation mode.

Test Switch

Pressing the test switch less than 5 seconds

will initiate a light source test (last for 3 secs).

If the test switch is pressed for more than 10

seconds, the device will be reset (delete all

errors).

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation or maintainance

must be done by authorized personnel only.

2. The device must be connected to the mains

power supply through a fuse dependent by the

total amount of the line’s power load.

3. The replacement of the battery and the light

source must be done using parts of the same

type, by the manufacturer or by a competent

person.

4. In case of inactive use for a period greater

than 2 months, disconnect the battery by pulling

out the battery’s connector.

5. I s not allowed to discard batteries into t i

common trash bins, they must be

discarded only in battery recycling

points. Do not incinerate.

Connection to module (After request)

This luminaire can be connected to any of the

following modules: Remote module, address

module, wireless module and fault relay

module. If you connect it to a module that

supports inhibit or rest mode, you should know

that these commands can be cancelled only

during normal mode (ie. not in emergency). For

installation refer to step 2 of the istallation

procedure in page 3.

Also refer to the user’s manual of each module

for additional information.

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

0: Non maintained (*)

A: Including test device

F: Automatic test gear complying with IEC

61347-2-7 denoted EL-T

180: 3 hour duration

Maintained operation: The luminaire lights its

illumination source, when it is powered by the

mains power supply or not.

(*) Non Maintained operation: The luminaire

turns on illumination source, only in case of

power supply failure.

Page 2 from 6

Status of LEDs

LEDs Description of indication

CHARGE : Battery charging, : battery charged, : disconnected battery

LAMP FAULT : Operation check, : lamp fault, : normal operation

BATT. FAULT : Autonomy test, : autonomy fault, : normal operation

Note : Blinking, : constantly on, : off

Note!! If a module will be used (except the fault

relay module), then the installer should fill in, on

the specification label, the letters B C.

X0AF

923293007_09_001

8 01

Page 3 from 6

INSTALLATION INSTRUCTIONS

Initial installation

1 Untighten the screw and pull up the reflector.

2 Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type 2x1mm²

or any other type, at least equal to it’s mechanical and electrical properties). Make a hole in the

center of the gasket by using a small screwdriver. Pass the round cable through the gasket. Detach

the power terminal, connect the wires as shown in the picture and attach the power terminal (10A

max). If you use a module (except the wireless module) pass the 2 signal cables on the A, B terminals

minding the correct polarity. Depending on the module that will be used, the cables could have

different names. In A, signals +L, C are also connected, while signals -L, NC/NO are connected on

the terminal B.

3 Refit the reflector (mind the correct orientation), tighten the screw securely and the luminaire is ready

for mounting.

4 Place the battery’s connector to the corresponding connector of the luminaire.

5 Mount the luminaire on the ceiling.

NOTE!! After finishing the installation you must power the luminaire for at least 24 hours in

order to completely charge the battery. The rated autonomy duration can be achieved after that

time.

Cable

entry

hole

Battery pack replacement.

It can be done only by a competent person and after the mains interruption.

1. Remove the luminaire from the suspended ceiling (figure 3 on page 4).

2. Remove the battery pack from the suspended ceiling.

3. Disconnect the connector and remove the old battery pack.

4. Connect the new battery pack (step 4 of the installation instructions) and place it in the position of

the old one.

5. Place the removed parts back and power the device.

Important notice for the installed luminaires in one area !!!

The installer must connect the battery’s connector first and then should power the luminaire.

The time between batteries connection must be, at least 1.5 minute.

With this variation, it is ensured that the non synchronized Automatic Autonomous Test for two or more

luminaires installed in one area, is not conducted in the same day.

923293007_09_001

Page 4 from 6 923293007_09_001

Mounting the lamp in suspended ceiling.

Set up the lamp to the suspended ceiling as it is shown bellow (Required opening 110mm):

Step 1

Pass the battery pack into the ceiling then bend the springs, to get into the hole of the suspended

ceiling, as you can see to the next figure.

Step 2

Push up the luminaire, as shown in figure 2.

Step 3

Continue to push upwards until the lamp locks.

If you want to pull off the device, put a flat blade

screwdriver, between the device and the ceiling.

Figure 2

Figure 3

Figure 1 Ø110mm

NOTE: The length of the battery pack cable is 70 cm.

CAUTION : Do not view directly with bare eyes.

230V

Page 5 from 6

LED MODULE CHARACTERISTICS

Olympia Electronics S.A.

75 C max. across the board °

3-3,2V DC

2.3W

0405185

fixed connection between main pcb and led module

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

Lamp fault

indication LED

ATTENTION!!!

During installation follow this light direction.

Corridor

lighting

Open

area

lighting

FAULT

LAMP

CHARGE

BATT.

FAULT

LAMP

CHARGE

BATT.

96 mm

72 mm

125 mm

FAULT

LAMP

CHARGE

BATT.

Battery

fault

indication

LED

Battery

charge

indication

LED

Figure 4

The light source contained in this luminaire shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

FAULT

LAMP

CHARGE

BATT.

GR-292/M/HL

GR-293/M/HL

GR-292/M/HL

GR-293/M/HL

923293007_09_001

A-290/BAT

286 mm 31 mm

33 mm

TEST

Test

button

TEST TEST

TEST

50 mm

Page 6 from 6

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty

is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which

accompanies each product. This warranty ceases to exist if the buyer does not follow the technical

instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods

provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully

agreed to them in writing. Products that have been damaged can be returned to the premises of our

company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the

buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the

buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

[email protected]

923293007_09_001

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere olympia electronics Laterne Handbücher

olympia electronics

olympia electronics GR-2100/ST Bedienungsanleitung

olympia electronics

olympia electronics GR-490/ADR Bedienungsanleitung

olympia electronics

olympia electronics BAU LIGHT Series Bedienungsanleitung

olympia electronics

olympia electronics KLIN-20/ST/ADR Bedienungsanleitung

olympia electronics

olympia electronics GR-220/DUO/M Bedienungsanleitung

olympia electronics

olympia electronics GR-939/30L/LT Bedienungsanleitung

olympia electronics

olympia electronics Slim Light Series Bedienungsanleitung

olympia electronics

olympia electronics CLASSIC LIGHT Series Bedienungsanleitung

olympia electronics

olympia electronics GR-427/12L Bedienungsanleitung

olympia electronics

olympia electronics Classic Light Series Bedienungsanleitung

olympia electronics

olympia electronics GR-900/30L/SC Bedienungsanleitung

olympia electronics

olympia electronics GR-8/leds Bedienungsanleitung

olympia electronics

olympia electronics GR-427/12L/MAR Bedienungsanleitung

olympia electronics

olympia electronics GR-290 Bedienungsanleitung

olympia electronics

olympia electronics Double Easy Light GR-391/L Bedienungsanleitung

olympia electronics

olympia electronics POWER LIGHT Series Bedienungsanleitung

olympia electronics

olympia electronics GR-940/15L/MAR Bedienungsanleitung

olympia electronics

olympia electronics GR-470 Bedienungsanleitung

olympia electronics

olympia electronics GR-290/WP Bedienungsanleitung

olympia electronics

olympia electronics GRL-29 WP Bedienungsanleitung

olympia electronics

olympia electronics GR-579/L/90/WP Bedienungsanleitung

olympia electronics

olympia electronics WATERPROOF POWER LIGHT Series Bedienungsanleitung

olympia electronics

olympia electronics GR-490/WP/ADR Bedienungsanleitung

olympia electronics

olympia electronics GRL-38/90/M Bedienungsanleitung

Beliebte Laterne Handbücher anderer Marken

KYOWA

KYOWA KW-9114 Bedienungsanleitung

Stahl

Stahl ECOLUX 6610 Series Bedienungsanleitung

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Bedienungsanleitung

PRG

PRG VARI LITE VL5 Bedienungsanleitung

Raytec

Raytec VARIO2 series Bedienungsanleitung

ENSA

ENSA LEDBT18WS2 Bedienungsanleitung

LUG

LUG OFFICE LB LED N/T Bedienungsanleitung

GE Wallighter 250 Bedienungsanleitung

Draper

Draper RLEDL19/B Bedienungsanleitung

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Bedienungsanleitung

Panasonic

Panasonic EY3741B57 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LCC8T Bedienungsanleitung

Coolon

Coolon WDN-140 Bedienungsanleitung

Holiday Travel

Holiday Travel 834873 Bedienungsanleitung

BEGA

BEGA 84 036 Bedienungsanleitung

BEGA

BEGA 33 596 Bedienungsanleitung

Dale Tiffany

Dale Tiffany GT701162 Bedienungsanleitung

Wagan

Wagan Brite Nite Pop-Up USB Lantern Bedienungsanleitung

olympia electronics GR-292/M/HL Bedienungsanleitung

Beliebte Laterne Handbücher anderer Marken