Olympus TERRA II Bedienungsanleitung

TERRA II — Getting Started Guide EN-1

Intended Use

The TERRA II X-ray diffraction analyzer is a portable system designed primarily for analyzing a

variety of powder sample types. Phase identification is obtained by comparing the diffraction

signature of a sample with a database of XRD mineral patterns.

Do not use the TERRA II analyzer for any purpose other than its intended use.

Instruction Manual

Before using the TERRA II analyzer, thoroughly review the TERRA II User’s Manual (P/N: 10-015488-

01EN). Use the product as instructed. The User’s Manual contains essential information on how to use

this Olympus product safely and effectively. Keep the User’s Manual in a safe, accessible location.

Safety Signal Word

Indicates a potentially hazardous situation and calls attention to an operating procedure, practice, or

the like that if not correctly performed or adhered to may result in minor or moderate personal injury,

material damage, particularly to the product, destruction of part or all of the product, or loss of data.

Contents of the Case

• TERRA II analyzer

• AC power adaptor

• Li Ion batteries (4)

• External sample-shaker assembly

• Sample cells (1 Kapton and 1 Mylar)

• Sample cell screws (8)

• USB flash drive (loaded with software, database, and documentation)

• Power keys (2)

•Microspatula

•Balldriver

•Samplecrusher

• Sample sieve

CAUTION

TERRA II

X-Ray Diffraction Analyzer

Getting Started Guide

EN-2 TERRA II — Getting Started Guide

Connections

All connectors are on the front panel of the analyzer.

To Connect AC Power to the TERRA II

If an unauthorized power supply cord is used to power the instrument, Olympus cannot guarantee

the electrical safety of the equipment.

1. Hold the power supply output plug with the flat edge in the orientation shown, and then insert it

into the Power connector.

2. Plug one end of the AC power cord firmly into the power supply.

3. Plug the other end of the power cord into a live AC (mains) power outlet.

Power connector USB connectorExternal Shaker connector

CAUTION

TERRA II — Getting Started Guide EN-3

To Turn On the Analyzer

Turn the power key clockwise to the ON position.

The system briefly displays the message:

Welcome to TERRA

Please wait

After a few minutes, the display reads:

Cooling to: –45

Current temp: (temperature)

After the detector cools to –45 °C, the main menu appears.

To Turn Off the Analyzer

In case of an emergency:

Turn the power key to the OFF position.

Quickly press twice the Stop/Emergency Shutoff button.

Under normal conditions:

a) Select Shut Down from the main menu to power down the TERRA II analyzer.

The display reads:

Shutting down...

Please wait...

b) After the analyzer has shut down, turn the power key to the OFF position.

Stop/Emergency Shutoff button

EN-4 TERRA II — Getting Started Guide

To Load a Sample

1. Unlock the sample carrier by pulling up the lever.

2. Pull up the carrier handle to remove the sample carrier.

3. Prepare and load a small amount of material (enough to fill the gap created by the spacer) into the

sample carrier cell assembly side A.

For more info on preparing and loading samples, see the TERRA II User’s Manual (P/N: 10-015488-

01EN).

Side A

TERRA II — Getting Started Guide EN-5

4. Fully insert the sample carrier back into the sample chamber, making sure that side A and the

“Align Sample Here” arrow are oriented as shown below.

5. Lock the sample carrier in place by pushing down the lever.

6. In the main display, select Start Acquisition.

7. Press the Check button ( ) to start the test.

Equipment Disposal

Before disposing of the TERRA II, check your local laws, rules, and regulations, and follow them

accordingly.

General Warnings

Instruments with a damaged detector or tube must be returned to your local distributor or the

manufacturer. Care should be taken to limit the release of beryllium from the instrument.

Electrical Warnings

The instrument must only be connected to a power source corresponding to the type indicated on the

rating label.

If an unauthorized power supply cord is used to power the instrument, Olympus cannot guarantee

the electrical safety of the equipment.

Trademarks

All brands are trademarks or registered trademarks of their respective owners and third-party entities.

Side A

CAUTION

EN-6 TERRA II — Getting Started Guide

Radiation Profiles

Table 1 on page EN-6 represents the typical radiation dose measurements to an operator of the

TERRA II analyzer. More specific radiation profiles for each instrument can be found on the included

USB flash drive. To convert from µSv/h to mR/h, divide the value by 10.

Table 1 Radiation level measurements

Measurement

point

Measured radiation

level (mR/h)

Distance from

surface (cm) Comments

A <0.05 2 Front top panel

B<0.05 2Left side of case

C <0.05 2 Front side of case

D<0.05 2Right side of case

E <0.05 2 Back side of case

F<0.05 2Bottom of case

Page intentionally left blank

Olympus Scientific Solutions Americas, 48 Woerd Avenue, Waltham,

MA 02453, USA

www.olympus-ims.com

Printed on Rolland Hitech50,

which contains 50 % post-

consumer fiber.

10-015489-01EN

Rev. 2, October 2019

*10-015489-01EN*

50%

EN-8 TERRA II — Getting Started Guide

Inhaltsverzeichnis

Andere Olympus Messgerät Handbücher

Olympus

Olympus USPM-RUIII Series Bedienungsanleitung

Olympus

Olympus OMCL-AC200TN-C3 Bedienungsanleitung

Olympus

Olympus Vanta L Series Bedienungsanleitung

Olympus

Olympus U-GAN Bedienungsanleitung

Olympus

Olympus EPOCH 650 Bedienungsanleitung

Olympus

Olympus DS-3000 Bedienungsanleitung

Olympus

Olympus ORBEYE OME-V200 Bedienungsanleitung

Olympus

Olympus Vanta L Series Bedienungsanleitung

Olympus

Olympus BIX III Bedienungsanleitung

Olympus

Olympus Magna-Mike 8600 Bedienungsanleitung

Olympus

Olympus WS 100 - 64 MB Digital Voice Recorder Bedienungsanleitung

Olympus

Olympus OMCL-AC240TS-C3 Bedienungsanleitung

Olympus

Olympus SOLTIVE Bedienungsanleitung

Olympus

Olympus DELTA 50 Bedienungsanleitung

Olympus

Olympus CIX100 Bedienungsanleitung

Olympus

Olympus OMCL-AC240TN-C3 Bedienungsanleitung

Olympus

Olympus BTX III Bedienungsanleitung

Olympus

Olympus USPM-RU-W Series Bedienungsanleitung

Olympus

Olympus 38DL PLUS Bedienungsanleitung

Olympus

Olympus 27MG Bedienungsanleitung

Olympus

Olympus STM7-AF Bedienungsanleitung

Olympus

Olympus OMCL-AC160TN-C3 Bedienungsanleitung

Olympus

Olympus 45MG Bedienungsanleitung

Olympus

Olympus USPM-RU-W Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung