Olympus BX53 Bedienungsanleitung

INSTRUCTIONS

BX53

SYSTEM MICROSCOPE

This instruction manual is for the Olympus System Microscope Model BX53.

To ensure the safety, obtain optimum performance and to familiarize yourself fully with the use

of this microscope, we recommend that you study this manual thoroughly before operating the

microscope.

Retain this instruction manual in an easily accessible place near the work desk for future reference.

A X 7 8 5 5

In accordance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment,

this symbol indicates that the product must not be disposed of as unsorted municipal waste, but

should be collected separately.

Refer to your local Olympus distributor in EU for return and/or collection systems available in your

country.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

BX53

CONTENTS

Correct assembly and adjustments are critical for the microscope to exhibit its full performance. If you are going to assemble

the microscope yourself, please read section 10, “ASSEMBLY" (pages 34 to 37) carefully.

IMPORTANT -- Be sure to read this section for safe use of the equipment. -- 1-3

13-26

5-7

8,9

10-12

1 MODULE NOMENCLATURE

2 CONTROLS

3 FLOW OF OBSERVATION

4 SIMPLIFIED OBSERVATION PROCEDURE

4-1 Basic Operation (Until Observation of Specimen) ..................................................................... 10,11

4-2 Microscope Adjustments (How to Improve the Observed Image)..................... 11,12

1Adjusting the Interpupillary

Distance................................................................................11

2Adjusting the Left and Right

Focusing...............................................................................11

3Adjusting the Centering.................................12 4Adjusting the Contrast.....................................12

5 USING THE CONTROLS

5-1 Base..............................................................................................................................................................................................................13-16

1Adjusting the Brightness..............................13 2Using the Light Intensity Preset

Switch.......................................................................................13

3Using the ECO/NORMAL Switch......14 4Using the Filters.............................................14-16

5-2 Focusing Block............................................................................................................................................................................... 17,18

1Focusing Controls...................................................17 2Adjusting the Focus..............................................17

3Replacing the Fine Adjustment

Knob...........................................................................................18

4Adjusting the Coarse Adjustment

Knob Tension................................................................18

5Pre-focusing Lever.................................................18

5-3 Stage............................................................................................................................................................................................................19-21

1Placing the Specimen......................................19 2Using the Auxiliary Slide Holder.........19

3Adjusting the X- and Y-Axis Knob

Tension................................................................................. 20

4Rotating the Stage ..................................... 21

5Adjusting the Stage Height..................... 21

5-4 Observation Tube................................................................................................................................................................... 22-24

1Adjusting the Diopter....................................... 22 2Using the Eye Shades.................................... 22

3Using the Eyepiece Micrometer

Disk............................................................................................ 23

4Selecting the Light Path of the

Trinocular Tube........................................................ 23

5Adjusting the Tilt..................................................... 24 6Using Eyepieces Incorporating a

Micrometer...................................................................... 25

5-5 Condenser................................................................................................................................................................................................... 25

1Compatibility of Objectives and

Condensers................................................................... 25

5-6 Immersion Objectives................................................................................................................................................................. 26

1Using Immersion Objectives................. 26

5-7 Objectives with Correction Collar.............................................................................................................................. 26

6 CAMERA RECORDING

7 TROUBLESHOOTING GUIDE

8 SPECIFICATIONS

9 OPTICAL CHARACTERISTICS (UIS2 Series)

10 ASSEMBLY -- See this section for the replacement of the light bulb. --

11 LAMP HOUSING INSPECTION SHEET

28-30

31,32

34-37

PROPER SELECTION OF THE POWER SUPPLY CORD........................................................ 39,40

BX53

Fig. 1

SAFETY PRECAUTIONS (Fig. 1)

IMPORTANT

This microscope employs a UIS2 (Universal Infinity System) optical design, and should be used only with

UIS2 eyepieces, objectives and condensers for the BX2 series. (Some of the modules designed for the BX

series and objectives/eyepieces for the UIS series are also usable. For details, please consult Olympus

or the catalogues.) Less than optimum performance may result if inappropriate accessories are used.

1. After the equipment has been used in an observation of a specimen that

is accompanied with a potential of infection, clean the parts coming in

contact with the specimen to prevent infection.

· Moving this product is accompanied with the risk of dropping the spe-

cimen. Be sure to remove the specimen before moving this product.

· In case the specimen is damaged by erroneous operation, promptly

take the infection prevention measures.

· Follow the procedures described in Chapter “Getting Ready” (see on

page 2) prior to using the accessories of this product. Otherwise, the

stability of the device will be lost and the dropped specimen will cause

the possibility of infection.

2. Install the microscope on a sturdy, level table or bench.

3. Be careful not to tilt the microscope too much. Otherwise, the mobile

parts such as the light path selector knob may move in unintended

directions.

4. The surfaces of the lamp housing on the rear of the microscope will

become extremely hot during operation. When installing the microscope,

make sure to allow ample free space (10 cm or more) around and in

particular above the lamp housing.

5. When installing the microscope, route the power cord away from the

lamp housing. Should the power cord come in contact with the hot lamp

housing, the power cord could melt and cause electric shock.

6. To avoid potential shock hazards and burns when replacing the light

bulb, set the main switch @ to “ ” (OFF) then disconnect the power cord

from the wall outlet in advance. Whenever you replace the bulb during

use or right after use, allow the lamp housing, and bulb to cool before

touching. (Fig. 1)

Designated bulb 12V100WHAL (PHILIPS 7724)

Always use the designated lamp bulb. Using other bulb may

cause malfunction.

7. Always use the power cord provided by Olympus. If no power cord is

provided, please select the proper power cord by referring to the section

“PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of this

instruction manual. If the proper power cord is not used, product safety

performance cannot be warranted.

8. Always ensure that the grounding terminal of the microscope and that of

the wall outlet are properly connected. If the equipment is not grounded,

Olympus can no longer warrant the electrical safety performance of the

equipment.

9. Never insert metallic objects into the air vents of the microscope frame

as this could result in electrical shock, personal injury and equipment

damage.

10. The standard service life of the lamp housing is eight (8) years of use or

20,000 hours of total power ON period, whichever is the shorter period.

For details, see Inspection Sheet on page 38.

CAUTION

Safety Symbols

The following symbols are found on the microscope. Study the meaning of the symbols and always use the equipment

in the safest possible manner.

Symbol Explanation

Indicates that the surface becomes hot, and should not be touched with bare hands.

Indicates a non-specific general hazard. Follow the description given after this symbol or in

instruction manual.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Caution indications

Caution labels are placed at parts where special precaution is required when handling and using the microscope. Always

heed the cautions.

Caution label

position

Lamp housing

[Caution against high temperature]

Caution label

position

Rear panel

[Caution against high temperature]

If a caution label is dirty or peeled off, contact Olympus for the replacement or other inquiry.

1 Getting Ready

Fig. 2

1. A microscope is a precision instrument. Handle it with care and avoid

subjecting it to sudden or severe impact. Also note that the microscope

does not have a waterproof construction.

2. Do not use the microscope where it is subjected to direct sunlight, high

temperature and humidity, dust or vibrations. (For the operating conditions,

refer to section 8, “SPECIFICATIONS”.)

3. When moving the microscope, remove the observation and specimen

and carefully carry the microscope by holding the grasping part on the

rear of the arm and the front part of the base as shown in Fig. 2.

To prevent damage to the microscope, never hold it by the stage

or coarse/fine adjustment knob.

· Even when moving the microscope along the desktop surface, be sure

to remove the specimen in advance.

· When the microscope needs to be packaged for forwarding to a remote

location, contact Olympus.

Please do not lift up the microscope by holding the bottom side of the

power supply cover (black) located on the rear panel.

4. When the accessories of this product are used, make sure that the system

height does not exceed 1 meter. Otherwise, the stability of the device will

be lost.

CAUTION

BX53

2 Maintenance and Storage

1. To clean the lenses and other glass components, simply blow dirt away using a commercially available blower and wipe

gently using a piece of cleaning paper (or clean gauze).

If a lens is stained with fingerprints or oil smudges, wipe it gauze slightly moistened with commercially available absolute

alcohol.

· Since the absolute alcohol is highly flammable, it must be handled carefully.

Be sure to keep it away from open flames or potential sources of electrical sparks --- for example, electrical

equipment that is being switched on or off, which could cause ignition of a fire.

Also remember to always use it only in a well-ventilated room.

· Set the main switch to “ ” (OFF) and wait for the lamp housing to cool down sufficiently before proceeding

to maintenance.

2. Do not use organic solvents to clean the microscope components other than the glass components. To clean them,

use a lint-free, soft cloth slightly moistened with a diluted neutral detergent.

3. Do not disassemble any part of the microscope except for the parts that are specified to be disassembled in this manual,

as this could result in malfunction or reduced performance.

4. After using the microscope, set the main switch to “ ” (OFF), wait for the lamp housing to cool down sufficiently, and

keep it covered with a dust cover during storage.

5. Before disposing of this product, be sure to follow the regulations and rules of your local government.

3 Caution

If the microscope is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition,

the equipment may also be damaged. Always use the equipment as outlined in this instruction manual.

The following symbols are used to set off text in this instruction manual.

: Indicates a potentially hazardous situation which, if not avoided, may result in minor

or moderate injury or damage to the equipment or other property. It may also be used

to alert against unsafe practices.

} : Indicates commentary (for ease of operation and maintenance).

4Intended use

This instrument has been designed to be used to observe magnified images of specimens in various routine work and

research applications.

Do not use this instrument for any purpose other than its intended use.

This instrument is considered a medical device in the following countries: US, and China.

This device complies with the requirements of directive 98/79/EC concerning in vitro diagnostic

medical devices. CE marking means the conformity to the directive.

CAUTION

1MODULE NOMENCLATURE

}The modules mentioned below show only the typical product names. As there are some products that are not mentioned

but also applicable to this microscope, check the latest catalogues or consult Olympus.

For the products marked “ *”, also read their instruction manuals.

Eyepieces

· WHN10X

· WHN10X-H

Revolving nosepiece

· U-D6RE

· U-D7RE

· U-D7RES

· U-D7REA

Slide holder

· U-HLST-4

· U-HLD-4

· U-HLDT-4

Stage

· U-SVRB-4

· U-SVRO

Observation tube

· U-BI30-2

· U-TBI-3

· U-TR30-2

· U-TTLBI

Intermediate attachment

· U-TRU

· U-CA

· U-DO3

Arm (or vertical illuminator)

· BX3-ARM

· BX3-URA*

· BX3-RFAS*

· BX3-RFAA*

Lamp housing

· U-LH100-3

Condenser

· U-SC3

· U-AAC

· U-UCD8

· BX3-UCD8A

BX53

2CONTROLS

}If you have not yet assembled the microscope, read section 10, “ASSEMBLY” (pages 34 to 37).

Interpupillary distance adjustment

scale (Page 11)

* The U-SHG (thin type) and U-SHGT (thick type) stage feed

knob rubber caps can be attached optionally.

Diopter adjustment ring

(Page 11)

Slide holder (Page 19)

Aperture iris diaphragm ring

(Page 12)

Filter mount (Page 15)

Field iris diaphragm ring

(Page 12)

Light preset adjustment

screw (Page 13)

Coarse adjustment tension

adjustment ring (Page 18)

Light path selector knob

(Page 23)

Condenser height adjustment

knob (Page 12)

Allen screwdriver

holder

Y-axis knob*(Page 20)

X-axis knob*(Page 20)

Coarse adjustment

knob (Page 17)

Filter knobs (Page 15)

ND6, ND25 and LBD from the front to

the rear (In-out possible from the other

side)

Main switch (Page 1)

I: ON

: OFF

Pre-focusing lever

(Page 18)

Fine adjustment knob

(Page 17)

Detachable.

Coarse adjustment knob

(Page 17)

Filter knobs (Page 15)

ND6, ND25 and LBD from the front

to the rear

(In-out possible from the other side)

Pilot LED

Green lighting: Lamp bulb ON

Red lighting: Auto OFF

Human sensor (Page 14)

Light intensity preset switch

(Page 13)

Brightness adjustment knob

(Page 13)

ECO/NORMAL switch (Page 14)

ECO indicator (Page 14)

ECO: ON (Green)

NORMAL: OFF

Andere Handbücher für BX53

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus IX2-RFSPOT Bedienungsanleitung

Olympus

Olympus SZX16 Bedienungsanleitung

Olympus

Olympus BHS Bedienungsanleitung

Olympus

Olympus CH2 Series Betriebsanleitung

Olympus

Olympus MIC-D Betriebsanleitung

Olympus

Olympus U-LGPS Bedienungsanleitung

Olympus

Olympus bx40 Bedienungsanleitung

Olympus

Olympus IX2-DSU Bedienungsanleitung

Olympus

Olympus BX46 Bedienungsanleitung

Olympus

Olympus DSX1000 Bedienungsanleitung

Olympus

Olympus BH2-5RE Montageanleitung

Olympus

Olympus FH Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus CX21LED Bedienungsanleitung

Olympus

Olympus BX51 Bedienungsanleitung

Olympus

Olympus FV3000 Bedienungsanleitung

Olympus

Olympus VANOX Betriebsanleitung

Olympus

Olympus ORBEYE Handbuch

Olympus

Olympus CX23 Bedienungsanleitung

Olympus

Olympus CX33 Bedienungsanleitung

Olympus

Olympus SZX7 Bedienungsanleitung

Olympus

Olympus CX31 Bedienungsanleitung

Olympus

Olympus CX43 Bedienungsanleitung

Olympus

Olympus U-DA Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung