Panasonic AJ-BS900 Bedienungsanleitung

AJ- P

Operation Instructions

S.S

BASE STATION

- 1 -

Safety precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (service) instructions in the

literature accompanying the appliance.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD AND ANNOYING INTERFERENCE,

USE THE RECOMMENDED ACCESSORIES

ONLY.

WARNING:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS

EQUIPMENT TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, REFER CHANGE OF SWITCH

SETTING INSIDE THE UNIT TO QUALIFIED

SERVICE PERSONNEL.

FCC Note:

This device complies with Part 15 of the FCC Rules.

To assure continued compliance follow the attached

installation instructions and do not make any

unauthorized modifications.

This equipment has been tested and found to comply

with the limits for a class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference when the equipment is operated in a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be required to

correct the interference at his own expense.

Thank you very much for purchasing this AJ-BS900P Base Station (referred to throughout these instructions as “the unit”).

The unit is connected to a DVCPRO or DVCPRO50 camera recorder to configure a transmission system which uses a tri-axial cable

to enable the camera recorder to be operated as a system camera.

Use of non-compressed wide-band 360 Mbps serial component signals makes high picture quality transmission possible so that the

high picture quality of the images shot by the DVCPRO camera recorder are transmitted with their high picture quality kept intact.

This serves to expand the range of the DVCPRO camera recorder’s operating formats.

Notes

≥≥When the unit is connected, external input signals cannot be recorded on tape inside the camera

recorder.

“CAM” must be selected as the REC SIGNAL setting on the REC/PB/RET menu of the camera

recorder.

≥≥For details on mounting the spacer provided with the AJ-CA900P camera adapter used in

combination with the unit, consult your dealer.

Depending on the version of the software being used with the camera recorder, it may be necessary

to update it, in which case you should consult your dealer.

- 2 -

Safety precautions..................................................................... 1

Features .................................................................................... 2

Checkpoints for system connections ......................................... 2

Parts and their functions............................................................ 3

Front panel..................................................................................................3

Rear panel ..................................................................................................7

PIX output menu indications...................................................... 9

PIX output setting menu indications ...........................................................9

Structure of setting menus..........................................................................9

MAIN MENU 1/2 screen .......................................................... 10

MAIN MENU 2/2 screen .......................................................... 12

Shading adjustment................................................................. 13

Shading menu operation procedure (example: black shading) ................13

Connectors and signals........................................................... 14

Switches .................................................................................. 16

Removing the boards................................................................................16

Setting the board switch positions ............................................................17

Setting the microswitch position ...............................................................18

Switching the controller.............................................................................18

Specifications .......................................................................... 19

The unit has the following features.

≥It enables high picture quality transmission by means of non-compressed wide-band 360 Mbps serial component signals.

≥It uses a tri-axial cable.

≥It enables a DVCPRO camera recorder to be operated as a system camera.

≥It enables transmission up to 2000 meters when three AJ-RP900P Repeaters are used. (*1)

≥It enables the transmission of the signals of two audio channels.

≥It enables RET 1CH and PROMPT 1CH transmission.

≥It has a compact size equivalent to one-half of a rack unit.

≥It can also be operated using DC power.

≥It can perform the VTR operations of the camera recorder. (*2)

Features

*1 The power supply is subject to limitations. Consult your dealer when configuring the system.

*2 During VTR playback operations (PLAY, FF or REW), the BS output pictures and sound will be switched to the playback mode. Under the current version,

however, the images of the camera will be viewed since the playback board has not been installed. As far as the audio signals are concerned, the signals

on the tape will be output from BS during VTR playback operations (PLAY, FF or REW): this means that care should be taken when the camera recorder’s

microphone is used.

Bear in mind the following checkpoints when connecting the camera recorder to the unit’s system.

1Remember that if the power is turned on or off while the camera’s menu is open, the menu will appear on the viewfinder.

2When the unit is connected, the RET SW operations will be canceled on the camera’s REC/PB/RET menu.

3When connecting the unit to a camera recorder, do not supply the signals to the GENLOCK connector on the camera.

4The triax and ECU (extension control unit) cannot be used at the same time for the camera recorder.

5When the triax is connected, some of the settings (such as GAIN, CAM-BAR SW, WHITE BAL and SHUTTER) selected by

the switches on the camera recorder will not take effect.

6When the triax is connected, the composite video signals (CAM OUT, VIDEO OUT) of the camera recorder will be non-

standard signals.

Checkpoints for system connections

Contents

- 3 -

Parts and their functions

Front panel

CABLE

SHORT ALARM

FUSE

HEAD POWER

OFF

MAIN

OFF

FUSE

OPEN

DIGITAL TRIAX

400V 1A

250V T 2.5A L

5Power fuse (FUSE)

This is the main power supply fuse of the AJ-BS900P. Use a dedicated DC fuse (400V 1A) which can withstand inrush.

6Camera AC power fuse (FUSE)

This is the fuse of the power supply to the camera head. Use a dedicated DC fuse (400V 1A) which can withstand inrush.

7CABLE indicators

These indicators show the status of the camera cable.

OPEN: Indicates that the camera cable is open. (In cases where, for instance, a connector has become disconnected or a wire

has broken.) The power supply to the camera is off when this indicator is lit.

SHORT: Indicates that the camera cable is shorted. The power supply to the camera is off when this indicator is lit. If the

SHORT indicator lights, the cable needs to be inspected.

8ALARM indicator

This indicator blinks when a problem has occurred. If a monitor has been connected to PIX OUT, letters representing the alarm

concerned will be displayed on the monitor simultaneously. For further details, refer to the table below.

1MAIN switch

This is the on/off switch for the main power supply.

This switch operates only when the unit is operated on AC

power. It does not work when it is operated on DC power.

<Note>

When DC power is supplied, whether the switch is ON or

OFF depends on whether the main power switch on the DC

power supply is ON or OFF.

2HEAD POWER switch

This is the on/off switch for the power supply to the camera

head.

<Note>

This switch also supplies power to the AJ-RP900P

repeater.

3MAIN power indicator

Lights when the main power supply is turned on.

4Head power indicator

Lights when the power supply to the camera head (AJ-CA900P) is turned on.

ALARM LED status

Blinks rapidly

Blinks slowly

Lights

Description of alarm

The indicator lights when 11and

22have occurred simultaneously.

11The temperature inside the unit

is higher than the reference

value.

22One or both fans have stopped

working because a problem

has occurred.

“TEMP HI!”

“FAN STOP!”

“TEMP HI & FAN STOP!”

Letters spelling out the alarm

- 4 -

=MIC button

This button is used to switch the intercom microphone on and off. It has three positions: ON, OFF, and PTT. (PTT: Audio

transmission continues as long as the button is held down.)

<INTERCOM level knob

This knob is used to adjust the volume of the microphone

input to the intercom.

Parts and their functions

Front panel

GENLOCK

VTR

ENABLE

REW

SET UP

MON SEL

KNEE

POINT

KNEE

SLOPE

OFF

(PUSH)

OFFSC H

PHASE

INTERCOM

PGM

OFF

PTT

MIC

PRIVATE

SYSTEM

PUSH

PHASE

OFF

B SUP

RIAX

9Intercom XLR connector

This is used to connect a headset to the intercom.

:PGM level knob

This knob is used to adjust the volume of the PGM audio

mixed into the signal fed to the intercom headset.

?Phase adjustment buttons

These buttons are used to adjust the phase selected using the phase adjustment switch >.

;SYSTEM/PRIVATE selector switch

This is used to toggle the intercom between the system and

private modes.

SYSTEM: The intercom is connected to the system via the

communication connector on the rear panel of

the unit.

PRIVATE:The intercom is not connected to the system via

the communication connector on the rear panel

of the unit.

>Phase adjustment switch

The available settings are SC PHASE, OFF, and H PHASE.

SC PHASE: Selects SC phase adjustment.

OFF: No phase adjustment is performed.

H PHASE: Selects H phase adjustment.

@GEN LOCK indicator

This indicator lights when the camera’s synchronization is locked using the signal input via the GEN LOCK connectors on the

rear panel.

<Note>

This indicator blinks if there is something wrong with the GEN LOCK signal. When this happens check the GENLOCK signals.

- 5 -

Parts and their functions

MAWB button

This is the auto white balance button. It does not work

when the LWHITE BAL switch is set to the PRST

position.

Button LED lit: Auto white balance in progress.

Button LED dark: Auto white balance completed.

Button LED stops blinking and goes off: Auto white balance

error.

NABB button

This is the auto black balance button.

Button LED lit: Auto black balance in progress.

Button LED dark: Auto black balance completed.

Button LED stops blinking and goes off: Auto white balance

error.

OBAR switch

This switch is used to output a bar signal from the AJ-

BS900P. The camera head does not switch to bar mode.

HVTR WARNING indicator

This indicator lights when a VTR operation error occurs.

ICALL button

This button is used to call the camera. This button’s LED

lights when a call is made from the camera.

KR TALLY indicator

This indicator lights when an R tally signal is being input via

the TALLY IN connector.

JG TALLY indicator

This indicator lights when a G tally signal is being input via

the TALLY IN connector.

Front panel

WHITE BAL (white balance selector) switch

PRST: This position should be selected when there is no

time to adjust the white balance. It uses the 3200

K white balance value stored in memory.

A or B: The white balance memory is set to A or B.

VTR

ENABLE

WHITE

BAL

REW

Base Station AJ -

FF STOP

SHUTTERSET UP

PIX SEL

KNEE

POINT

KNEE

SLOPE

GAMMA

DETAIL

M.PED

PLAY

AWB

CHECK

AUTO IRIS IRIS

GAIN

FILTER

ABB

BAR

ENABLE

PAINTING

GAIN

AUTO KNEE

GAIN

REC CHK

START / STOP

CALL

TALLY

VTR WARNING

OFF

(PUSH)

PRST

BLACK

ENG

SEQ

B SUP

S.V

S.S.

100(60)

1000

120 250

500

2000

CD G

XYZ[

]

65ª1

BREW button

This is the rewind button for the VTR.

CFF button

This is the fast forward button for the VTR.

DSTOP button

This is the stop button for the VTR.

EPLAY button

This is the play button for the VTR.

REC CHK button

This button is used to display the recording status of the

VTR.

GSTART/STOP button

This button is used to turn the VTR’s recording operation

on and off.

AVTR ENABLE button

This button is used to operate the VTR from the base

station.

ON: Activates VTR operation using the controls on the

front panel (buttons Bto G). The time code is

displayed at PIX OUT.

OFF: Deactivates VTR operation using the controls on the

front panel. The time code is not displayed at PIX

OUT.

<Note>

The VTR’s playback video signal is not output from the

base station.

- 6 -

Parts and their functions

Front panel

aMONI SEL switch

This switch is used to switch the signals output from the

PIX and WFM jacks on the rear panel of the AJ-BS900P.

_KNEE POINT knob

This knob is used to set the manual knee point.

`DETAIL knob

This knob allows adjustment of the master DETAIL setting.

^GAMMA knob

This knob is used to change the camera’s master gamma

setting.

bSET UP button

This button is used to make camera settings.

When it is lighted, menus are displayed at PIX OUT.

cSET UP dial

This dial is used to select settings on the setting menus.

After selecting the desired setting by turning the dial, press

to enter it.

Menu settings can be performed when the bSET UP

button is lighted.

When the bSET UP button is not lighted, the SYNCHRO

SCAN speed can be set; when SYNCHRO SCAN is

selected.

eShutter speed selector switch

This switch is used to select the shutter speed. The

available settings are SYNCRO SCAN Super V and 1/100

to 1/2000.

Moving the switch when the SHUTTER button is in the off

position will not cause the shutter to operate.

dSHUTTER button

This button activates the operation performed using the

shutter speed selector switch e. It should be put into the

on position when using an electronic shutter.

[! indicator

This lights when the lens extenders (x2) are used with the

camera.

]KNEE SLOPE knob

This knob is used to set the manual knee slope.

RPAINTING ENABLE button

This button is used to enable painting (gain knob Sand

black knob T) operation.

VAUTO IRIS button

This button is used to toggle auto iris operation on and off.

Lit: Auto iris operation on.

Dark: Auto iris operation off.

WLED digital indicator

This indicator displays the F value of the lens.

When changes are made to the gain or filter settings, the

corresponding values are displayed for about two seconds.

Also, pressing the CHECK button Z toggles the display in

sequence among the gain, filter, and F values.

<Note>

“---”appears when the camera recorder’s power is OFF.

UIRIS knob

When the AUTO IRIS button Vis in the on position, the

value selected using this knob is added or subtracted to the

IRIS LEVEL setting in the USER MENU.

When the AUTO IRIS button Vis in the off position, this

knob is used to perform adjustment of the iris setting.

<Note>

Set the lens manual/auto selector switch to AUTO.

YFILTER indicator

This indicator lights when the filter position is shown by the

LED digital indicator.

XGAIN indicator

This indicator lights when the gain value is shown by the

LED digital indicator.

\M PED knob

This knob is used to adjust the master pedestal setting.

ZCHECK button

Pressing this button multiple times causes first the GAIN

indicator and then the FILTER indicator to light. When the

GAIN indicator is lit the LED digital indicator shows the filter

position, and when the FILTER indicator is lit the LED

digital indicator shows the gain value.

SGAIN knobs

These are the R and B gain adjustment knobs.

TBLACK knobs

These are the R and B pedestal adjustment knobs.

PAUTO KNEE button

This button is used to toggle auto knee operation on and

off.

Lit: Auto knee operation on.

Dark: Auto knee operation off.

QGAIN buttons

These buttons are used to switch the camera’s gain setting.

- 7 -

Parts and their functions

EXT DC IN

GEN–

LOCK ENC

ENC

PIX

Y/G

4:2:2

SDI OUTOUTIN

OP4

OP3

WFM

TALLY

FUSE 400V 15A

SIGNAL

GND

AC IN

AUDIO

OUT

CH 1

PUSH

CH 2

PUSH

COMMUNICATION

PB/B

PR/R

WFM

RET 1

RET 2

PROMPT

57689

ENC

PIX

Y/G

4:2:2

SDI OUTOUT

PB/B

PR/R

WFM

OP1

OP2

OP1

OP2

Rear panel

1GEN LOCK connectors

These are the standard external signal input connectors

used when locking the camera’s synchronization to an

external sync signal.

2RET 1 connectors

These are the input connectors for return signal 1, which is

sent to the camera.

6COMMUNICATION connector

This connector is used for making connections to an

intercom system. The supports types of intercom system

are 2W, 4W, and RTS. Use the switch on the BS AUDIO

board to select the system. For details, refer to “Switches”

(page 17).

7AUDIO CH1 connector

This is the output connection for the camcorder’s MIC CH1

signal.

3RET 2 connectors

These are the input connectors for return signal 2, which is

sent to the camera.

4PROMPT connectors

These are the input connectors for the teleprompter signal,

which is sent to the camera.

5Triax connector

This is the triax connector used for making connections to

the AJ-CA900P.

8AUDIO CH2 connector

This is the output connection for the camcorder’s MIC CH2

signal.

9DC 12V IN (external power supply input) jack

This jack is used to connect an external battery for use as a

power supply.

<Note>

Use the AJ-B95 AC adapter (12V, 13A), available as an

optional accessory, for the DC power.

<OP3 connector

This connector is for making connections to an extension

control unit (ECU) or remote control operation panel

(RCOP). The compatible ECU model is the AJ-EC3P.

However, the RCOP cable is required for connection. For

further details, consult your dealer.

=OP4 connector

This connector is for making connections to the camera

select unit (CSU) of a master control panel (MCP). The AJ-

BS900P is not compatible with any currently available

CSUs. Plans call for a compatible model to be developed

in future.

>WFM control connector

This is an output connection used for waveform monitoring.

One-waveform, two-waveform, and three-waveform control

are supported.

:GND terminal

This terminal is used to ground the AJ-BS900P.

;Power connector

This connector is used to supply power to the AJ-BS900P.

- 8 -

Parts and their functions

Rear panel

?TALLY connector

This is the connector for the R tally and G tally signals. It

can be used for PM tally.

@DC power fuse (FUSE)

This fuse is for the AJ-BS900P’s DC power supply. Use a

dedicated DC fuse (400V 15A) which can withstand inrush.

A4 : 2 : 2 connectors

These connectors are for component serial digital output.

They are activated if the AJ-YA901P option board is

installed. One component may be connected to each

output BNC connector. The output signals comply with the

SMPTE259M-C standard.

BY/G, PB/B, and PB/R connectors

These output connectors are for component signals or

RGB signals. Use the switch on the BS DIGITAL board to

select the system. For details, refer to “Switches”(pages

18).

CVideo output connectors

These are output connectors for component video signals.

DPIX output connector

This is the output connector for the picture monitor signal.

Signal switching is performed using the PIX SEL switch.

EWFM output connector

This is the output connector for the waveform monitor

signal. Signal switching is performed using the MONI SEL

switch.

OP1 connector

This connector is not used on the current version of the AJ-

BS900P.

GOP2 connector

This connector is not used on the current version of the AJ-

BS900P.

- 9 -

PIX output menu indications

PIX output setting menu indications

When the SET UP button is pressed so that it lights, setting menu indications are output via the PIX output connector.

The setting menus consist of main menus and submenus. Setting menus are displays one page at a time. All of the

setting menu screens and their structure are shown in the diagram below.

The MAIN MENU consists of two screens, 1/2 and 2/2. These screens are used to open the submenus.

To open a submenu, select it by turning the SET UP dial and then press the SET UP dial.

To return to the MAIN MENU from a submenu, turn the SET UP dial to align the arrow cursor with the desired menu

title, then press the SET UP dial.

For details on the submenu items, refer to the Instruction Manual of the camera recorder used.

Structure of setting menus

MAIN MENUS

MAIN MENU 1/2

MAIN MENU 2/2

SUB MENUS

1SYNCHRO SCAN

2VR DATA

3MATRIX

4DTL SETTING

5ADDITIONAL DTL

6SKIN TONE DTL

7KNEE / LEVEL

8FLARE / GAMMA

9GENLOCK / IRIS

:CAMERA SW MODE

;CAMERA SETTING

<AUTO SHADING

=DIAGNOSTIC

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Panasonic Zubehör Handbücher

Panasonic

Panasonic CF-VNP011AU Bedienungsanleitung

Panasonic

Panasonic MA3U649 Bedienungsanleitung

Panasonic

Panasonic HG-TC101 Bedienungsanleitung

Panasonic

Panasonic PAW-DEWPOINTSENSOR Bedienungsanleitung

Panasonic

Panasonic MA3Z793 (MA793) Bedienungsanleitung

Panasonic

Panasonic MA2Z784 (MA784) Bedienungsanleitung

Panasonic

Panasonic MA3D652 Bedienungsanleitung

Panasonic

Panasonic PM-25 Series Bedienungsanleitung

Panasonic

Panasonic LM10 Bedienungsanleitung

Panasonic

Panasonic Light Emitting Diodes LNJ214R8ARA Bedienungsanleitung

Panasonic

Panasonic DVCPRO AJ-BS901P Bedienungsanleitung

Panasonic

Panasonic KX-HNS105C Bedienungsanleitung

Panasonic

Panasonic MA2ZD14 Bedienungsanleitung

Panasonic

Panasonic CA-LSR10U - Sirius Satellite Radio Receiver Bedienungsanleitung

Panasonic

Panasonic KX-HNS103FX Bedienungsanleitung

Panasonic

Panasonic LS-400 Series Bedienungsanleitung

Panasonic

Panasonic LS-H Series Bedienungsanleitung

Panasonic

Panasonic ECONAVI CZ-CENSC1 Bedienungsanleitung

Panasonic

Panasonic MA4SD01 Bedienungsanleitung

Panasonic

Panasonic MALHxxxYG Series Bedienungsanleitung

Panasonic

Panasonic HL-C1-WL Series Bedienungsanleitung

Panasonic

Panasonic MA3X791 (MA791) Bedienungsanleitung

Panasonic

Panasonic KX-HNS103AZ Bedienungsanleitung

Panasonic

Panasonic ECONAVI CZ-CENSC1 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung