Panasonic LP-GS Series Bedienungsanleitung

Laser Marking System

Laser Marker NAVI smart

Operation Manual

LP-GS series

LP-RC series

LP-RF series

LP-RV series

ME-NAVIS2-OP-1

2020.10 https://panasonic.net/id/pidsx/global

Preface

Thank you for purchasing this product.

Read this manual carefully to make full use of the product and to ensure its safe and proper

operation.

The English version of this instruction manual is the original version. All other languages are

translations that are based on the original documentation.

This product has been strictly checked and tested prior to packaging. However, make sure

that the product has not been damaged during transportation and operates properly before

using it. If the product was damaged or does not operate as specified in this manual, contact

our service center or sales office.

Liability and copyright for the hardware

Panasonic pursues a policy of continuous improvement of the design and performance

of its products. Therefore we reserve the right to change the manual/product without

notice. In no event will Panasonic be liable for direct, special, incidental, or consequential

damage resulting from any defect in the product or its documentation, even if advised of the

possibility of such damages.

This manual and everything described in it are copyrighted. You may not copy this manual, in

whole or part, without written consent of Panasonic.

Please direct support matters and technical questions to your local Panasonic

representative.

Disclaimer

The applications described in the manual are intended as examples only. The purchase of

our products described in the manual shall not be regarded as granting of a license to use

our products in the described applications. We do not warrant that we have obtained some

intellectual properties, such as patent rights, with respect to such applications, or that the

described application may not infringe any intellectual property rights, such as patent rights,

of a third party.

Trademarks

•Windows® is a registered trademark or trademark of Microsoft Corporation in the United

States and other countries.

•QR Code® is a registered trademark of DENSO WAVE INCORPORATED.

•Adobe®, Adobe® Logo, Adobe Reader®, and Adobe® Illustrator® are registered

trademarks of Adobe Inc. in the U.S.A. and other countries.

•The Bluetooth® wordmark and logos are registered trademarks owned by the Bluetooth

SIG, Inc.

2 ME-NAVIS2-OP-1

Preface

• EtherNet/IPä is a trademark of ODVA, Inc.

• All other product names and companies provided in this manual are trademarks or

registered trademarks of their respective companies.

ME-NAVIS2-OP-1 3

Important symbols

One or more of the following symbols may be used in this documentation.

The following symbols are used to indicate the type of hazard.

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate

injury.

Indicates a property damage message.

The following symbols are used to indicate the type of instructions to be observed.

Indicates an operating procedure which must not be performed.

Indicates an operating procedure which must be followed to operate the unit safely.

Indicates an operating procedure which must be performed carefully.

4 ME-NAVIS2-OP-1

General safety precautions

Always follow these important safety precautions!

You have acquired a product with components of laser class 4 (marking laser) and laser

class 2 (guide laser). The laser classifications are defined in the standard IEC 60825-1

“Safety of laser products”. Laser class 4 refers to “laser products for which intrabeam viewing

and skin exposure is hazardous and for which the viewing of diffuse reflections may be

hazardous. These lasers also often represent a fire hazard”. Make sure to take safety

measures required to use Class 4 laser products subject to the local laws and regulations of

the country or region in which this laser product is used.

Never look at the direct laser beam, neither directly nor through a lens or any other optical

components. Laser radiation into the eye causes blindness or serious damage to the eye.

A specularly reflected laser beam is also dangerous.

Never expose your skin, clothing or any other flammable object to the laser radiation. Your

skin will be severely burned and there is a risk of fire.

Do not use this product near flammable gas or objects (organic solvents such as thinner

or gasoline), in a dusty place or anywhere where fire is strictly prohibited. There is a risk of

fire.

Do not install this product in wet places except for water-resistant parts. Never conduct

wiring or maintenance work with wet hands or when the product surface is wet.

Otherwise, there is a risk of an electrical shock or malfunction.

Do not open or disassemble this product. Otherwise, there is a risk of exposure to laser

radiation or of electrical shock.

ME-NAVIS2-OP-1 5

General safety precautions

Do not insert hands or objects in the gaps of the exhaust port or air intake. This may result

in injuries, electrical shock, or failure of this product.

Wear laser protective goggles against laser radiation within the laser controlled area.

Never look into the direct or specularly reflected laser beam even when you are wearing

the protective goggles. The protective goggles are designed to protect your eyes from

diffuse reflection only.

Build a protective enclosure with proper reflectance, durability and thermal resistance to

enclose the laser radiation range without leakage.

Construct an interlock system, e.g. to stop laser radiation when the access panel of the

protective enclosure is opened.

After you turn off the power supply of this product, the laser safety officer must remove the

key and keep it.

Be sure to connect the laser head (LP-RV: the oscillator unit with laser head) to a controller

of this product series which has the same model number. Otherwise there is a risk of

exposure to laser radiation or failure.

Read all safety instructions and manuals thoroughly, and do not operate, install and

connect this product with any other methods except the instructions provided in the

manuals. Otherwise the safety protection and functions provided by the device may be

affected and may cause injury, electrical shock or exposure to the laser beam.

Turn off the power of this product before you conduct wiring, connection, or maintenance

work. Wiring and maintenance should be done by an expert engineer or a qualified

electrician. Otherwise, there is a risk of an electrical shock or fire.

When connecting the power supply, be sure to ground this product properly. Otherwise,

there is a risk of malfunction and electrical shock in case of a failure or leakage current.

LP-RF/LP-RV: Make sure that the fiber cable is not put under mechanical stress or

squeezed during installation. Do not install this product into systems that impose excessive

load on the fiber cable such as head movement units. If the fiber cable is damaged, there

is a risk of exposure to laser radiation.

6 ME-NAVIS2-OP-1

General safety precautions

Remove the dust and gas with a dust collector or exhauster. Depending on the material of

the workpiece to be marked, dust or gas, which can be harmful for the human body and

this product, may be generated.

(1) (2)

(1) Protective enclosure

(2) Dust collector

When using an assist gas for laser processing, take safety measures to protect operators

from exposure, ignition, toxic effects, excess or lack of oxygen.

To carry this product, wear non-slip gloves and safety shoes. Hold this product with both

hands. Do not transport this product by holding the cables and connectors. In case the unit

falls down, it may cause injury.

LP-RC/LP-RF/LP-RV: Carry the controller of this product series with two persons. Lifting or

carrying the product without assistance can cause muscle strain or back injury.

Install this product in a stable place without vibration and shock. In case the unit falls down,

it may cause injury.

LP-RF/LP-RV: Do not touch the surface of the laser head during and right after operation.

It becomes hot and may cause burn injuries.

ME-NAVIS2-OP-1 7

Network security

Implementing measures to protect your network is crucial to keep your network and its traffic

secured.

As you will use this product connected to a network, your attention is called to the following

security risks.

• Leakage or theft of information through this product

• Use of this product for illegal operations by persons with malicious intent

• Interference with or stoppage of this unit by persons with malicious intent

It is your responsibility to take precautions such as those described below to protect yourself

against the above network security risks.

• If this product is connected to a network that includes PCs, make sure that the system

is not infected by computer viruses or other malicious entities (using a regularly updated

antivirus program, anti-spyware program, etc.).

• Use this product in an environment that has LAN, VPN (virtual private network) or leased

line network.

• Use this product in an environment where only limited people concerned can enter.

• Use this product and connected devices such as a PC and tablet securing safety.

• Do not install this product in locations where the product or the cables can be destroyed

or damaged by persons with malicious intent.

Note that incorrect setting of the connection to the existing LAN might cause malfunction in

the devices on the network. Consult your network administrator before connecting.

8 ME-NAVIS2-OP-1

Available documentation

The following documents are included on the CD-ROM Laser Marker Smart Utility.

You need Adobe Reader (Version X or later) of Adobe Inc. to read the PDF version of the

manuals.

“Laser Safety Guide”

• Intended audience: All users

• This manual describes the safety measures required before you start to operate the laser

marking system.

“Setup and Maintenance Guide”

• Intended audience: System integrators and persons responsible for installing the laser

marking system.

• This manual describes the items which are necessary for the installation and

maintenance of the laser marking system.

‒ Specifications and dimensions

‒ Installation and connection methods

‒ Input and output specifications, descriptions of input and output signals, including

timing charts

‒ Maintenance information

‒ Troubleshooting

“Laser Marker NAVI smart Operation Manual”

• Intended audience: Operators of the laser marking system.

• This document describes how to operate the laser marking system using the

configuration software Laser Marker NAVI smart.

“Serial Communication Command Guide”

• Intended audience: Machine builders and system integrators

• This manual describes the communication commands for the external control of the

laser marking system via RS232C, Ethernet, or optional network unit (EtherNet/IP or

PROFINET).

“Serial Communication Command Guide: LP-400/V compatible mode”

• Intended audience: Machine builders and system integrators

• This manual describes compatible communication commands for the external control of

the LP-400/LP-V series.

ME-NAVIS2-OP-1 9

Product models

This document covers the LP-GS, LP-RC, LP-RF and LP-RV models listed in the table.

Multiple models may be described collectively. Therefore, illustrations and screenshots may

slightly vary, depending on the model. Different settings or technical data, however, are

specified in the text.

Model Collective name

LP-GS051 (-E)

LP-GS051-F (-FE/-FN) LP-GS051

LP-GS051-L (-LE)

LP-GS051-LF (-LFE/-LFN) LP-GS051-L

LP-GS051 (-L)

LP-GS052 (-E)

LP-GS052-F (-FE/-FN) LP-GS052

LP-GS series

LP-RC350S LP-RC350S LP-RC series

LP-RF200P LP-RF200P LP-RF series

LP-RV200P LP-RV200P LP-RV series

10 ME-NAVIS2-OP-1

Andere Handbücher für LP-GS Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Messgerät Handbücher

Panasonic

Panasonic NA1-11 Bedienungsanleitung

Panasonic

Panasonic ShowStopper PV-SS2710 Bedienungsanleitung

Panasonic

Panasonic LP-400 Series Gebrauchs- und Wartungshandbuch

Panasonic

Panasonic RRQR100 - IC RECORDER Bedienungsanleitung

Panasonic

Panasonic LH2H preset Bedienungsanleitung

Panasonic

Panasonic LH2H preset Bedienungsanleitung

Panasonic

Panasonic k-nl304k Bedienungsanleitung

Panasonic

Panasonic SV-3800 Bedienungsanleitung

Panasonic

Panasonic AG-RT850P Bedienungsanleitung

Panasonic

Panasonic KW2M-A Bedienungsanleitung

Panasonic

Panasonic WJHD500 - DIGITAL DISC RECORDE Bedienungsanleitung

Panasonic

Panasonic LP-V10U-C Bedienungsanleitung

Panasonic

Panasonic RR-QR230E Bedienungsanleitung

Panasonic

Panasonic VP-7722A Bedienungsanleitung

Panasonic

Panasonic DMR-UBT1GL-K Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-V4600 Bedienungsanleitung

Panasonic

Panasonic KW2G Eco-POWER METER Bedienungsanleitung

Panasonic

Panasonic DMRE20 - DVD VIDEO RECORDER Bedienungsanleitung

Panasonic

Panasonic FZ-VNP001U Bedienungsanleitung

Panasonic

Panasonic RS-790S Bedienungsanleitung

Panasonic

Panasonic WJ-NX100/2E Bedienungsanleitung

Panasonic

Panasonic AG6124 Bedienungsanleitung

Panasonic

Panasonic KW2M Bedienungsanleitung

Panasonic

Panasonic KW2G Eco-POWER METER Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung