Panasonic WV-Q110E Bedienungsanleitung

Before attempting to connect or install this product,

please read these instructions carefully and save this manual for future use.

Wall Mount Bracket

Model No. WV-Q110E

■Introduction

This bracket is used for mounting the colour camera WV-CW860 or WV-CW864 onto a wall.

There are two ways of cable exit available from the front or rear of the bracket.

• Installations for this product should be performed by qualified service personnel or system installers.

• Consult an expert about the resistible load weight of the installation surface and structure. Insufficient strength may

cause falling of the camera. Refer to the specifications of the products for weight.

Caution

The camera in the illustration is separately sold.

-2-

Front Cable Exit

1. Preparations

Specify the bracket fixing location, and then put in

four anchor bolts, or drill four bolt holes on the

installation surface. Refer to Dimensions on page 6.

2. Cable Bushing

Fit the supplied cable bushing into the front cable

exit of the bracket.

3. Cable Route

Route the connection cables from the front cable

exit through the bracket, and pull them out of the

pipe mouth.

4. Fixing Bracket

Fix the bracket to the wall using appropriate hard-

ware (not supplied): bolts and nuts, anchor bolts

and nuts, or the like.

5. Disassembly of Camera

(1) Remove the upper base from the camera by

loosening three screws, and then turn the upper

base to separate it.

(2) Remove the attachment pipe from the upper

base by loosening four screws.

Mark hole positions

Cable Bushing

Fixing Hardware

(Locally Procured)

Upper Base

Attachment Pipe

Camera

-3-

6. Setting Switches

Refer to Setting the Switches in the manual includ-

ed with the camera.

7. Cable Connection

Refer to CONNECTIONS in the manual included

with the camera.

8. Mounting Upper Base

Fix the upper base to the bracket using four screws.

9. Waterproofing

Fill the front cable exit with sealant.

10. Mounting Camera

(1) Aim the START arrow at the bent portion of the

leaf spring on top of the camera.

(2) Be sure to hook the fall prevention wire to the

bracket.

(3) Fix the camera to the upper base.

• Move up the camera so that the guide pins of

the camera come to the guide holes of the

upper base.

• Turn the camera counter-clockwise to the end,

viewing from the bottom.

• Fasten three screws.

START

Sealant

Cable Bushing

Outside

Inside the bracket

Cables

Camera Fixing Screw

Upper Base

Bending Leaf Spring

Fall Prevention Wire

Upper Base

Camera

-4-

Rear Cable Exit

1. Preparations

Specify the bracket fixing location, and then put in

four anchor bolts (not supplied), or drill four bolt

holes on the surface.

Remember that a cable access hole is necessary on

the wall in this case.

Refer to Dimensions on page 6.

2. Rear Cable Exit

(1) Remove the rear plate, and then punch out the

cable exit on it.

(2) Fit the supplied blank bushing into the front

cable exit of the bracket.

(3) Fit the supplied cable bushing into the rear cable

exit of the plate.

(4) Replace the rear plate to the bracket fastening

four screws.

3. Cable Routing

Route the connection cables from the rear cable exit

through the bracket, and pull them out of the pipe

mouth.

4. Waterproofing

Fill the rear cable exit with sealant.

5. Fixing Bracket

Fix the bracket to the wall using appropriate hard-

ware (not supplied): bolts and nuts, anchor bolts

and nuts, or the like.

Cable Access Hole

on the wall

Front Cable Exit

(Not Used) Rear Cable Exit

Rear Plate

Blank Bushing Cable Bushing

Fixing Hardware

(Locally Procured)

Sealant

Cable Bushing

Outside

Inside the Bracket

Cables

Mark hole positions

-5-

6. Disassembly of Camera

(1) Remove the upper base from the camera by

loosening three screws, and then turn the upper

base to separate it.

(2) Remove the attachment pipe from the upper

base by loosening four screws.

7. Setting Switches

Refer to Setting the Switches in the manual includ-

ed with the camera.

8. Cable Connection

Refer to CONNECTIONS in the manual included

with the camera.

9. Mounting Upper Base

Fix the upper base to the bracket using four screws.

10. Mounting Camera

(1) Aim the START arrow at the bent portion of the

leaf spring on top of the camera.

(2) Be sure to hook the fall prevention wire to the

bracket.

(3) Fix the camera to the upper base.

• Move up the camera so that the guide pins of

the camera come to the guide holes of the

upper base.

• Turn the camera counter-clockwise to the end,

viewing from the bottom.

• Fasten three screws.

START

Upper Base

Attachment Pipe

Camera Fixing Screw

Upper Base

Bending Leaf Spring

Fall Prevention Wire

Upper Base

Camera

-6-

Ø58

(269)

(111.5)

180

(210.5)

4-Ø10

240

Unit: mm

(50)

(90)

Ø25.4

■Dimensions

Fall Prevention

Wire Hook

Rear Cable Exit

(Punch out the hole when using)

Camera Fixing

Screw Hole x4

Front Cable Exit

-7-

■Specifications

Dimensions: 111.5(W) x 210.5(H) x 269(D) mm

Weight: 2 kg approx.

Weight and dimensions indicated are approximate.

Specifications are subject to change without notice.

■Accessories

Camera Fixing Screw .................................4 pcs

Cable Bushing............................................1 pc

Blank Bushing ............................................1 pc

NM0102-0 V8QA5987AN Printed in Japan

N19

Matsushita Electric Industrial Co., Ltd.

Web Site : http://www.panasonic.co.jp/global/

Inhaltsverzeichnis

Andere Panasonic Rack & Stand Handbücher

Panasonic

Panasonic NN-TK81LCSCP Bedienungsanleitung

Panasonic

Panasonic BT-WMA26G Bedienungsanleitung

Panasonic

Panasonic i-PRO WV-Q121B Bedienungsanleitung

Panasonic

Panasonic TY-ST65P20 Bedienungsanleitung

Panasonic

Panasonic TY-ST65PE8 Bedienungsanleitung

Panasonic

Panasonic WV-Q70 Bedienungsanleitung

Panasonic

Panasonic TY-WK42PV20 Bedienungsanleitung

Panasonic

Panasonic TY-ST65PV500 Bedienungsanleitung

Panasonic

Panasonic CA-FN50N Bedienungsanleitung

Panasonic

Panasonic TC349815 Bedienungsanleitung

Panasonic

Panasonic TY-WK42PR20 Bedienungsanleitung

Panasonic

Panasonic PAW-GRDSTD40 Bedienungsanleitung

Panasonic

Panasonic TY34WDM60J - STAND FOR CT34WDM60 Bedienungsanleitung

Panasonic

Panasonic ET-PKE1000S Bedienungsanleitung

Panasonic

Panasonic WV-Q169A Bedienungsanleitung

Panasonic

Panasonic TY-ST85P12 Bedienungsanleitung

Panasonic

Panasonic TY-WK15TA2U Bedienungsanleitung

Panasonic

Panasonic TY-CE103PS10 Bedienungsanleitung

Panasonic

Panasonic TY-CE85PS12 Bedienungsanleitung

Panasonic

Panasonic TY-ST10-M Bedienungsanleitung

Panasonic

Panasonic NNTK687S Bedienungsanleitung

Panasonic

Panasonic WV-Q150CE Bedienungsanleitung

Panasonic

Panasonic ET-PKL100H Bedienungsanleitung

Panasonic

Panasonic TY-ST32L7-S Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung