Panasonic CZ-RTC6 Bedienungsanleitung

Installation Instructions

Wired Remote Controller

Model No. CZ-RTC6

CZ-RTC6W

Safety Precautions ……………………… 2

Part Names (Control panel)……………… 4

Dimensions ………………………………… 4

Installation Precautions ………………… 5

Mounting …………………………………… 6

Setting ……………………………………… 9

Test run …………………………………… 11

Speciﬁcations …………………………… 11

Page

ENGLISH

Read through the Installation Instructions before you proceed with the installation.

In particular, please carefully read the “Safety Precautions”.

WEB-ACXF60-38393-EN

W1020-20423

NOTICE

The English text is the original instructions. Other languages are translations of the

original instructions.

Safety Precautions

Read before installation

 Read the Installation Instructions carefully to install the remote controller correctly and safely.

Be sure to read the “Safety Precautions” before installation.

 After the installation is complete, perform test operation to conﬁrm that no abnormality is

present.

 We assume no responsibility for accidents or damages resulting from methods other than those

described in the Installation Instructions or methods using unspeciﬁed parts.

Malfunctions that occur due to unauthorised installation methods are not covered by the

product warranty.

 Read the Installation Instructions supplied with indoor units as well.

WARNING CAUTION

This symbol refers to a hazard or unsafe

practice which can result in severe personal

injury or death.

This symbol refers to a hazard or unsafe

practice which can result in personal injury or

product or property damage.

Prohibited matters

Precautions for Installation setup

WARNING

• Turn oﬀthe circuit breaker of the units before installation.

• Ask your dealer or professionals for installation and

electric work.

• This remote controller must be installed in accordance

with National Wiring Regulations.

• Connect and ﬁx the speciﬁed cables for wiring securely.

• Do not allow the connection to be exposed to external

force from the cables.

• Choose an installation location that suﬃciently supports

the weight of the remote controller.

CAUTION

Do not use the remote controller at the following

locations.

• Location where condensation occurs

• Location where ﬂammable gases, etc. may leak

• Location where corrosive gases, etc. may leak

• Location with lots of water or oil droplets

(including machine oil)

• Location where voltage ﬂuctuation frequently occurs

• Location where there is a machine producing

electromagnetic radiation

• Location where droplets of organic solvents spread

• Location where acidic or alkaline solutions or special

sprays are frequently used

Do not operate with wet hands.

Do not wash with water.

Part Names (Control panel)

The control panel colour of CZ-RTC6W is white.

5) Start/Stop button

Starts/Stops operation.

2) Menu button

4) Enter button

Fixes the selected

content.

3) Up/Down

buttons

Selects an item.

1) LCD screen

●

When pressed repeatedly

during operation, this shows

operating status conﬁrmation,

set temperature, operation

mode, fan speed, ﬂap, and

the menu screen.

●

The menu screen is

displayed if you press while

stopped.

Note

Press centre No pen No glove

Dimensions

25 25 䃥4

4×10

3030

1510

(mm)

Supplied accessories

Screw

M3.8 x 16 (2)

Operating Instructions

(1)

Installation Instructions

(1)

Clamper

(1)

Remote control wiring is not supplied. (ﬁeld supplied item)

Installation Precautions

Installation location

Floor

1 to

1.5m

Install at the height of 1 to 1.5 m from the ﬂoor

(Location where average room temperature can be detected).

Install vertically against a wall or suitable supporting

structure.

Keep a space around the remote controller as detailed on

the ﬁgure shown left.

Avoid the following locations for installation.

•

By a window, etc. exposed to direct sunlight or external airﬂow

• In the shadow or backside of objects deviated from the room

airﬂow

• Location where condensation occurs

(The remote controller is not moisture proof or drip proof)

• Location near heat source

• Uneven surface

Keep distance of 1 m or more from the TV, radio and PC.

(Image blur or related noise may occur)

Remote control wiring

Wiring diagram

Indoor unit

Terminals for RC wiring

RC wiring (ﬁeld supply)

• No polarity

Type of wiring



Use cables of 0.75 to 1.25 mm

Total wire length: 500 m or less

(The wire length between indoor units

should be 200 m or less.)

Number of connectable units

Remote controller: Max. 2

Indoor unit:Max. 8



Use the ﬁeld supplied RC wiring with at least 1 mm in thickness of insulation part including the sheath.

Wiring Regulations may diﬀer depending on location. For ﬁeld wiring rules, please refer to your

LOCAL ELECTRICAL CODES.

You must ensure that installation complies with relevant rules and regulations.



Be careful not to connect cables to other terminals of indoor units (e.g. power source wiring terminal).

Malfunction may occur.



Do not bundle together with the power source wiring or store in the same metal tube. Operation error

may occur.



If noise is induced to the unit power supply, attach a noise ﬁlter.

Attention

Using 1 indoor unit Using more than 1 indoor unit

R1 R2

12 12

Indoor unit

(sub)

(main)

RC wiring

R1 R2

R1 R2 R1 R2

(main)

(sub)

Indoor unit Indoor unit Indoor unit

RC wiring

Wiring as shown below is prohibited.

R1 R2

12 12

Indoor unit

(sub)

(main)

RC wiring R1 R2

R1 R2

Indoor unit Indoor unit

RC wiring

When setting both the main and sub remote controllers

After installation, set one remote controller to [Main] and the other to [Sub] for [Main/sub] for “Setting”.

(See “Setting” section - “RC. setting mode”)

When using the remote controllers* in combination, set the CZ-RTC6(CZ-RTC6W) unit to [Sub].

*CZ-RTC5B, CZ-RTC6BL(CZ-RTC6WBL)

Note Remote controllers can be connected to any indoor unit for operation.

Mounting

1Remove the top case.

1Insert the screwdriver to the bottom case.

Insert the ﬂat-blade screwdriver to the claws as show in

the ﬁgure.

2Push the ﬂat-blade screwdriver in.

Push down the ﬂat-blade screwdriver along with the

slope of the claws until the top case comes oﬀ.

Bottom case

Top case

Claw (2 locations)

Flat-blade screwdriver

Top case

Bottom case

Claw

Flat-blade screwdriver

View A

Exposed type

*It is also possible to mount in the order

→

Screw

(Supplied)

Claw (2 locations)

1Mount the bottom case to the wall.

●Pass the wire through the wiring

hole in the bottom case and lay the

wire out along the groove.

Mount the top case.

●

Align the claws of the top

case and then align the

claws of the bottom case.

Cut here with

a nipper and

remove the burr

with a file.

Connect the remote control wiring.

• Be sure not to allow unnecessary wires to remain

in the remote controller case when wiring. Be

careful not to allow wires to be in contact with

parts on the PCB. For connection method, refer

“

Connection to the remote controller terminal

board

”

“

Attention

”

Avoid the

wire being

caught.

Hole for screw

Clamper

(supplied)

•

Insert the clamper from the

position indicated by the arrow,

as shown in the diagram at right.

•

Put the locking part of the

clamper in the channel as

indicated by the arrow.

•

If you lock at the top, it may not

be possible to close the bottom

case.

Remove the coating. Approx. 9 mm

Remove the sheath. Approx. 130 mm

●Make sure the wiring connection is in the

correct direction.

●

There will be a slight diﬀerence in length due

to the wiring diameter, so make adjustments

on site when performing the installation.

Remote controller

terminal board

Push the sheath

in to the back as

shown on the

illustration.

Insert the wire properly

into the channel on the

bottom case, and make

sure the wire is not

pinched when the case

is attached to the wall.

2Mount to the wall.

There are 2 types of wall-mounting methods: Exposed type and Embedded type.

Mounting the bottom case

Tighten the screws securely until the screw heads touch the bottom

case.

(Otherwise, loose screw heads may hit the PCB and cause

malfunction when mounting the top case.)

Do not over-tighten the screws.

(The bottom case may be deformed, resulting in the unit becoming

detached from the surface it is ﬁxed to.)

Connection to the remote controller terminal board

Depress the push button using a round bar or ﬁnger, insert the

remote control wiring securely from the wiring insertion slot and

release the push button.

Pull the remote control wiring lightly, and conﬁrm it is secured.

There is the danger of shorting if copper wire is exposed. Make sure

the wire is properly inserted.

Insertion slot

Push button

Remote controller terminal board

Attention

A protective ﬁlm is attached on the Control panel.

Embedded type

*It is also possible to mount in the order

→

Screw

(Supplied)

Claw (2 locations)

Connect the remote control wiring.

• Be sure not to allow unnecessary wires to remain

in the remote controller case when wiring. Be

careful not to allow wires to be in contact with

parts on the PCB. For connection method, refer

“

Connection to the remote controller terminal

board

”

“

Attention

”

Hole for screw

Mount the top case.

●

Align the claws of the top

case and then align the

claws of the bottom case.

●

If the wiring is difficult to

move, loosen the screw in

the lower case, work on the

wiring, then screw in the

screw after finishing the work.

3Mount the bottom case to

the wall.

●Pass the wire through the

wiring hole in the bottom case.

Avoid the

wire being

caught.

Clamper

(supplied)

•

Insert the clamper from the

position indicated by the arrow,

as shown in the diagram at right.

•

Put the locking part of the

clamper in the channel as

indicated by the arrow.

•

If you lock at the top, it may not

be possible to close the bottom

case.

Remote controller

terminal board

Remove the coating. Approx. 9 mm

●

Make sure the wiring connection

is in the correct direction.

Pass the wire under the rib.

A protective ﬁlm is attached on the Control panel.

Setting

Preparation: Turn on the circuit breaker of units and then turn the power on. The remote controller starts, and

wait until the [Assigning] display disappears.

(If [Assigning] continues to blink for 10 minutes or more, check the address setting of indoor

units. Refer to indoor/outdoor unit installation details.)

Language

1When stopped

Press .

When operating

Press repeatedly until the menu screen is

displayed.

•To return to the top screen, press .

2Select [Language].

Press

→.

Number for the

selected item

Total number of items 3Select the language

to display from

among

7 languages shown

on the right.

FRANÇAIS

DEUTSCH

ITALIANO

ESPAÑOL

POLSKI

РУССКИЙ

ENGLISH

Press

→→.

(Press to ﬁnish.)

•Default setting : ENGLISH

Maintenance func

RC. setting mode Auto address Detailed settings Sensor info. Service check

Check this item as necessary.

Steps 1 and 2 are common operations for each item.

Press and hold the

3 buttons simultaneously,

for at least 4 seconds.

Press , , .

2Select the

item to set.

Press →.

Number for the

selected item

Total number of items

RC. setting mode

3Set.

(Select the Code no. and Set data.)

Press →. (Repeat) Code no.

Set data

4Press .

After Selecting [YES], the unit restarts.

Code no

. Set data

01 Main/sub Set this when using 2 remote controllers. • 0000: Sub

• 0001: Main (factory setting)

2F Password change Set the administrator password. • 0000 to 9999

• 0000 (factory setting)

Auto address

3Set.

(Select the Code no. [A1] and O/D unit no.)

Press →. (Repeat) Code no.

O/D unit no.

4Press .

After Selecting [YES], the unit restarts.

Code no.

O/D unit no.

A1 Set the Auto address for each O/D unit no.

Select the O/D unit no. (outdoor unit) for Auto address. • Outdoor unit number



Set Auto address after all units are turned on and 90 seconds or more have passed.



Operate the units after Auto address is set and 90 seconds or more have passed.

Attention

Detailed settings

3Set.

(Select the indoor unit number, Code no. and Set data.)

(When selecting Code no., refer to the following table.)

Press →. (Repeat)

Indoor unit number

Set data

Code no.

4Press .

After Selecting [YES], the unit restarts.

Code no. Set data

31 Vent output

setting

Set this when connecting a commercially sold fan, etc. to the ventilation

fan output “FAN DRIVE:2P (White)” on the indoor control board.

*Dedicated cables (optional) are required.

• 0000: Not connected

• 0001: Connected

32 Temp sensor

setting

Set this when measuring the room temperature with the room temperature sensor of the remote

controller.

• When using the main and sub remote controllers, the main one is enabled.

• When using with the remote sensor in combination, set the indoor unit setting data.

This setting is not available during group-controlling.

• 0000: Indoor unit

• 0001: Remote controller

33 Temp display

setting Set the type of temperature display. • 0000: °C

• 0001: °F

* Depending on the type of indoor unit, Code no. may be displayed with 6 digits. In this case, read as follows.

e.g. 10 →000010

Sensor info.

This displays each sensor temperature of the remote controller, indoor units and outdoor units.

3Select.

(Select the unit number and

Code no.)

Press

→. (Repeat)

4Conﬁrm the content.

press .

●Pressing will return

to the Maintenance func

screen.

Service check

This displays the alarm history.

3Conﬁrm the content.

Press .

Information of the last 4 errors is displayed.

[

] shows that no error has occurred.

●Pressing will return to the Maintenance func screen.

●To delete the error history, press and select [YES].

Andere Handbücher für CZ-RTC6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Fernbedienung Handbücher

Panasonic

Panasonic CZ-RTC5A Bedienungsanleitung

Panasonic

Panasonic EUR511151 Bedienungsanleitung

Panasonic

Panasonic CZ-01ESM11P Bedienungsanleitung

Panasonic

Panasonic WV-CU50 Bedienungsanleitung

Panasonic

Panasonic CZ-RD52CP Bedienungsanleitung

Panasonic

Panasonic EUR7702KE0 Bedienungsanleitung

Panasonic

Panasonic AK-HRP1015G Bedienungsanleitung

Panasonic

Panasonic EUR511110 Bedienungsanleitung

Panasonic

Panasonic WVCU360C - SYSTEM CONTROLLER Bedienungsanleitung

Panasonic

Panasonic CZ-RWS3 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-ES35V Bedienungsanleitung

Panasonic

Panasonic WV-RC35 Bedienungsanleitung

Panasonic

Panasonic CZ-RWSU2N Bedienungsanleitung

Panasonic

Panasonic CZ-RTC6 Bedienungsanleitung

Panasonic

Panasonic AK-HRP1000G Bedienungsanleitung

Panasonic

Panasonic CZ-RTC2 Bedienungsanleitung

Panasonic

Panasonic EUR511158 Bedienungsanleitung

Panasonic

Panasonic CZ-RTC6BLW Bedienungsanleitung

Panasonic

Panasonic CZ-RC515UA Betriebsanleitung

Panasonic

Panasonic CZ-RTC4 Bedienungsanleitung

Panasonic

Panasonic CZ-RD513C Installations- und Betriebshandbuch

Panasonic

Panasonic CZ-RWSU3U Bedienungsanleitung

Panasonic

Panasonic EUR511171B Bedienungsanleitung

Panasonic

Panasonic EUR511163 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung