ParaBody 701 Bedienungsanleitung

701

PARABODY 525 PEC DEC OPTION

PRODUCT ASSEMBLY

INSTRUCTIONS SHEETS

REV1SI:ON C

! ! ! ATTENTION! ! !

UNLESS__O_T_HER~

C_~NNE~

_CAg_NSJS_T~F ONE LD BO_L Z’~

~HERS, AND

ONE (,O_LO~K..N_U_T,_

BOLT.

701 FACTOR 525 PEC DEC ATT. ASSEMBLYPARTS LIST (LEVEL 1)

SORT AND COI.£NT ALL PARTS BEFOREBEGINNING ASSEMBLY

ITEM

I0.

If.

12.

13.

14.

NAME/DESCRIPTION QTY

I/2X4-I/2IN.BOLT............................................................................................................

3/8X2IN.BOLT..................................................................................................................

3/4IN.WASHER....................................................................................................................

I/2IN.WASHER....................................................................................................................

3/8IN.WASHER..................................................................................................................

I/2IN.LOCKNUT.....................................................................~.........................................

3/8IN.LOCKNUT................................................................................................................

COTTER.LESSHITCHPIN....................................................................................................

CABLERETAININGCLIP....................................................................................................

3/4I.D.STARLOCKCOLLAR.............................................................................................

3/4IN.FLANGEBEARING..................................................................................................

KNOB.....................................................................................................................................

CARRIAGEGUIDE...............................................................................................................

2IN.SQ.ENDCAP..............................................................................................................

WELDMENTS/PARTS:

ITEM NAME/DESCRIPTION QTY

BEARINGHOUSING....................................................

(6352701)..................................

CENTERPULLEYBRACKET...................................... (6352401).......................................

KIGHTPECDECAILM................................................. (6354101)....................................... l

LEFTPECDECARM.................................................... (6354201)....................................... 1

RIGHT ARM ADVANCE - .

.............................................. (63~210t’)....,.,..-.:.,<....:...:...:.............. 1

LEFTARMADVANCE................................................ (635-2-20-I-)....}:.,:.).~:.).’...:~.~..!.~::.:.......... 1

4X12ROLLERPAD..................................................... (6176201)....................................... 2

4-t/2XI IN.PULLEY............................................. :...(3116101)....................................... 2

NOTE: BOLT LENGTH IS MEASUREDFROM THE UNDERSIDE OF THE HEAD OFTHE BOLT.

I////i//l

BOLT LENGTH

BOLT LENGTH RULER:

I/2 [ I/2

701 FACTOR525 PEC DEC ATT. ASSEMBLY PARTS LIST (ZEVEL 2)

SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY

HARDWARE."

ITEM NAME/DESCRIPTION QTY

10.

II.

3/8X2IN.BOLT.................................................................................................................. 1

3/8Xi-314IN.BOLT............................................................................................................. I

3/8IN.WASHER....................................................................................................................

1/4IN.WASHER.................................................................................................................... 2

3/8IN.LOCKNUT................................................................................................................ 2

3/8IN.LOWHEIGHTLOCKNUT....................................................................................... 2

318IN.NUT............................................................................................................................ 2

t/4-25IN.NUT....................................................................................................................... 2

D-RINGCABLECLIP........................................................................................................... l

PULLEYBRACKET.............................................................................................................. l

SWIVEL.................................................................................................................................. l

WELDMENTS/PARTS:

ITEM NAME/DESCRIPTION QTY

LINKCABLE................................................................. (6371801)....................................... 1

LOOPCABLE................................................................ (637I101).......................................

SHOCKCORD............................................................... (6271801).......................................

4-1/2X1IN.PULLEY................................................... (311610I)....................................... 3

NOTE: BOLT LENGTH IS MEASUREDFROM THE UNDERSIDE OF THE HEAD OF THE BOLT.

Iiiiiiii

BOLT LENGTIt

BOLT LENGTH RULER:

I._1

COTTERLE~HITCHPIN

LEFT PEC DEC

2 SO. END CAP (4) 0

RIGHTPEC DEC ARM

I~Y BRACKET

3/4 IN. WASHER (2)

LEFT ARMA[

RIGHT ARMAE

"-. ~~/-- .CAM STOP

CARRIAGE GUIDES (2)

// .//

~/~~i/2 X 4 I/2 IN BOLT (2)

~, ,

// 3/4 LD. STAR~OCK COL~ (2)

~2 SQ. END C~ (2) ~ ~ P~BODY I~C-

~ AS~ INST. 70

~01

NOTE:

I0.

FACTOR525 PEC DEC ATT. ASSEMBLYINSTRUCTIONS(LEVEL 1) ,--.

IF THE SHROUDIS ASSEMBLEDTO THE FACTOR525, IT WILL NEEDTO BE REMOVED

TO ASSEMBLETHE PEC DEC A’vrACHMENT. PLEASE REMOVETHE SHROUDAT TH][S

TIME BY CAREFULLYREMOVINGTIlE FOURTEEN(14) SHROUDFASTENERS.

Insert two (2) 2 IN. SQ. ENDCAPSinto both ends of the BEARINGHOUSING,as shown on drawing.

SECURELYassemble the BEARINGHOUSINGand the CENTERPULLEYBRACKETto the

FRONTUPRIGHTas shownon drawing, using two (2) I/2 X 4-I/2 IN. BOLTS,four (4) 1/2

WASHERS,and two (2) I/2 IN. LOCKNUTS. (THE CONNECTORPLATES ON THE BEARING

HOUSING AND THE CENTER PULLEY BRACKET HAVE SLOTTED HOLES. SHIFT THE

BEARING HOUSING DOWNAND THE CENTER PULLEY BRACKET UP AS FAR AS

POSSIBLE)

Insert four (4) 2 IN. SQ. ENDCAPSinto BOTHENDSof the LEFT, and RIGHTPECDECARMS

shown on drawing.

Assemble one (1) 314 IN: WASHER,and the LEFTARM.ADVANCEto the LEFT PECDECARM

shown on drawing. Also Assemble one (1) 3/4 IN. WASllEK,".,qd the RIGHTARMADVANCEto the~

RIGHT PEC DEC ARMas shown.

Insert four (4) 3/4 IN. FLANGEBEARINGSinto the BUSttlNGSof the BEARINGItOUSING,

shown on drawing.

Insert the LEFTand RIGHTPECDECARMSthrough the 3/,4 IN. FLANGEBEARINGSin the

BEARINGHOUSINGon their respective sides as shownon dr’awing, ~d SECUREthem in place with

two (2) 3/,4 I.D. STARLOCKCOL1.ARS.

Slide two (2) 4 X 12 ROLLERPADSonto the LEFTand RIGHTPEC DECARMS,until the

ROLLERPADis FLUSHwith the bottom of the ARMS.(IF A LUBRICANTIS REQUIRED,COAT

THE INSIDE OF THEROLI,ER PAl) WITll RUBIJINC ALCOIlOL. ALSO, ROTATINGTHE

PAD WHILE PUSHING UP WILL ilELP TO EASE ASSEMBLY)

Assemble two (2) KNOBSto two (2) COTTERLESSHITCHPINSas shown on drawing. Insert the

(2) COTTERLESSHITCHPINS through the BUSHINGSon th~ CAMSof the RIGHTand LEFTPEC

DECAR51S, and into the holes on the PEC ARMADVANCES.SEE DRAWING.

Attach two (2) CARRIAGEGUll)US ~o the CAB1STOPo,i the BEARINGltOUSINGwhere the

ARMADVANCESmakes contact with the CAMSTOP.

LOOSELYassemble two (2) 4-1/2 X I IN. PULLEYSand two (2~ CABLERETAININGCLIPS

CENTERPULLEYBRACKETas shown on dr-awing, using two (2) 3/8 X2 IN. BOLTS,four (,~) 13/8

WASHERS,and two (2) 3/8 IN. LOCKNUTS. (NOTE: THIS CONNECTIONWILL

TIGHTENEDAFTER TI4E CABLE I tAS BEEN ROUrED)

THIS CONCLUDES THE ASSFMBLY OF (LEVEL 1)

FACTOR525 PEC DEC ATT. ASSEMBLYINSTRUCTIONS (LEVEL 2) --.

LOOSENthe 3/8 X 4 IN. BOLTthat assembles the two (2) PULLEYS,and two (2) 1/2 IN. SPACEP,

the BASEdirectly behind the FRONTUPRIGHT.Removethe 3/$ IN. LOCKNUT,and the 3/g IN.

WASHER.Slide the BOLTout enough to remove the two (2) I/2 IN. SPACERS.Replace the 1/9- IN.

SPACERSwith one (1) 4-I/2. X1 IN. PULLEY,as shown in (VIEWB-B). Slide BOLTback

Replace the 3/8 IN. WASHER,and .3/8 IN. NUT. TIGHTENCONNECTIONSECURELY.

SECURELYassemble one (1) 4-1~ X 1 IN. PULLEYto the single hole in the BASEdirectly behind the

FRONTUPRIGHTas shownin (VIEWB-B) on drawing, using one (I) 3/8 XI-3/4 IN. BOLT,two

3/8 IN. WASHERS,and one (I)3/8 IN. LOCKNUT.

To assemble the LOOPCABLE,follow the cable routing diagram on drawing, and use the following

steps:

Assemble one end of the LOOPCABLEto the LEFTARMADVANCEand the other end ofthe

LOOP CABLE to the RIGHT ARMADVANCE(MAKE SURE THAT LOOP CABLE IS

ROUTED BETWEENTHE AB CRUNCHCABLE AND THE FRONT UPRIGHT) as shown

on drawing, using~.wo (2) 3/8 IN. NUT,four (4) 3/8 IN. WAS’HERS,and two (2) 3/8 IN.

HEIGItT LOCK NUT. (TIGHTEN THE CONNECTION ENOUGHTO REMOVETHE

PLAY, YET ALLOWING THE LOOP TO MOVEFREELY)

¯Drape the CABLEover the both PULLEYSon the CENTERPULLEYBR.kCKET. (THIS

WILL FORMA LOOP IN THE CENTER OF THE CABLE)

¯Position CABLERETAININGCLIPS in a 45 DEGREEposition over the PULLEYSand

CABLES,and tighten the two (2) PULLEYconnections SECURELY.SEE DRAWING.

To assemble the LINKCABLE,follow the cable routing diagram on drawing, and use the following steps:

¯LOOSELYassemble the PULLt"Y BRACKETto the LINK CABLEas shown in (DETAILE)

drawing, using two (2) I/4 IN. WASHER,and two (2) t/4-2S IN. NUTS.(LOCATEPULLEY

BRACKET HALF WAYUP ON TIlE THREADS OF THE LINK CABLE. DO NOT

TIGHTENNUTS AT TIllS TIME)

¯Slip one (I) 4-1/2 X I IN, PULLEYinto the LOOPofthe LOOPCABLEcreated from routing

STEP3. (VIEWD-D) While holding that PULLEYin the LOOP,SECURELYassemble the

PULLEYBRACKETover the PULLEYas show~l in (DETAILE) on drawing, using one (1) 3/~’,

2 IN. BOLT,two (2) 3;8 IN. WASI-IERS,and ot~e (I) 3~8 IN. LOCK

¯Route the LINKCABLEas shown on drawing. (ALSO SEE VIEWB-B)

¯Run the LINKCABLEthrough the pre-determined hole of:he D-RINGas shown in (DETAILA)

and attach one (1) D-RINGCABLECLIParound the ball end of the LINKCABLE.

Attach one (I) SHOCKCORDto the D-RINGCABLECLIP on the end ofthe LINKCABLEas shown

in (DETAILA).

Route tile SHOCKCORDup and around the prc-determined 2 IN. PULLEYabove the D-RINGas shown

in (VIEWC-C). and downto tile BASE.

Atmch one (l) SWIVELt° the end °fthe SHOCKCORD"Slipti:eendoftheSWIVEL°vertheL’P]N

on the BASE,and position the SWIVELdirectl: over the FIRSTPULLEYas shown in (VIEWB-B)

drawing.

701

NOTE:

lO.

FACTOR525 PEC DEC ATT. ASSEMBLYINSTRUCTIONS(LEVEL

The D-RINGCABLECLIPon the end of the LINKCABLEshould rcstjust above the D-RING.If the

LINKCABLEseemsto be pulling on the D-RINGor is resting too far above the D-RING,adjust it by

raising or lowering the two (2) 1/4-25 lN. NUTSthat attaches the LINKCABLEto the PULLEY

BRACKET.Whenthe correct height is obtained SECURELYtighten the two (2) 1/4-28 NUTStogether

around the PULLEYBRACKET.

To adjust the pre-stretch on the PECDECAILVIS:

Pull up on the COT’fERLESSHITCHPIN.

Swivel the ARMforward or backward.

Let the PIN drop downinto one ofthe two holes in the PECARMADVANCES.

Or let the PIN drop behind the PECARMADVANCES.

IF ASSEMBLING THE LEG PRESS ATTACHMENTNEXT, STOP HERE AND REFER TO

THOSE ASSEMBLY INSTRUCTIONS. IF ONLY ASSEMBLING TIIE PEC DEC ATTACHMENT

TO BASE UNIT, ~CONTINUE ON WITH THESE ASSEMBLYINSTRUCTIONS.

Wrapthe SHROUDaround the CABLESthat t-oute to the D-RING,and assemble the SHROUDto

BOTHSIDESof the MIDDLEU,’~PRIGHTas shown in (VIEWF-F) on drawing, using the fourteen (14)

SHROUD FASTENERS.

THIS CONCLUDESTHE ASSE~,IBLY OF (LEVEL 2), AND

THE ASSEMBLY OF THE PEC DEC ATTACHMENT FOR

THE FACTOR525 BASE UNIT.

SHOCKCC

SEED~I’AIL F--~

~EE VIEW C-C

o ;

L-PIN

FRONTOFI~,CHINE

SEE DET~,ILA

~SHROUD...C~.SEEVIEW F-F)

f LIN.__~K_~ABLZ /

~--D-RING CABL~ CtJP

~ LEG CURL/~ION

lAB CRUNCH CABLE

._A

r- D-R~NG

~$HROUI~FA_RI’ZNERS(I4.)

~o MIDDLEU PRIGF,’r

~~ SHROUD

VIEW F-F

FRONT OF MACHINE

VIEWB~B

FRONTOF MACHINE

DETAILC-C

VIEW D-D

FACTOR 525 PEC DEC~

Andere Handbücher für 701

Dieses Handbuch passt für folgende Modelle

Andere ParaBody Heim-Fitnessstudio Handbücher

ParaBody

ParaBody 895101 Bedienungsanleitung

ParaBody

ParaBody 843 Bedienungsanleitung

ParaBody

ParaBody PBF072 Bedienungsanleitung

ParaBody

ParaBody Parabody 660 Bedienungsanleitung

ParaBody

ParaBody 375101 Bedienungsanleitung

ParaBody

ParaBody 893103 Bedienungsanleitung

ParaBody

ParaBody Parabody 660101 Bedienungsanleitung

ParaBody

ParaBody 415101 Bedienungsanleitung

ParaBody

ParaBody PBF405B Bedienungsanleitung

ParaBody

ParaBody 828104 Bedienungsanleitung

ParaBody

ParaBody 874 Bedienungsanleitung

ParaBody

ParaBody 440 GYM SYSTEM Bedienungsanleitung

ParaBody

ParaBody PBF011 Bedienungsanleitung

ParaBody

ParaBody 58 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 812102 Bedienungsanleitung

ParaBody

ParaBody PBF010A Bedienungsanleitung

ParaBody

ParaBody PBF460 Bedienungsanleitung

ParaBody

ParaBody PBF206 Installationsanleitung

ParaBody

ParaBody LP5 Bedienungsanleitung

ParaBody

ParaBody 911101 Bedienungsanleitung

ParaBody

ParaBody FACTOR 625 Bedienungsanleitung

ParaBody

ParaBody 897104 Bedienungsanleitung

ParaBody

ParaBody PBF011AB Bedienungsanleitung

ParaBody

ParaBody 205101 Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Weider

Weider 8300 Hard Drive Bedienungsanleitung

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Weider

Weider 8700 I Kurzanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Weider

Weider WEMC10161 Bedienungsanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

cardiobull

cardiobull RA17 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung