Paradyne 4000E Bedienungsanleitung

IPD4-A2-GZ40-10 July 2005 1

4000E IP Broadband Loop Carrier

Installation Instructions

Document Number IPD4-A2-GZ40-10

July 2005

Contents

Software and Firmware License Agreement ...................................................... 1

Introduction ........................................................................................................ 3

Unpacking and Inspecting the Equipment ......................................................... 3

Installation Options ............................................................................................ 4

Installing Your Management Module .................................................................. 6

Installing Your Interface Module(s) ..................................................................... 7

Powering Up Your 4000E BLC ........................................................................... 9

Uplink Connections ............................................................................................ 12

Subscriber Lines ................................................................................................ 12

Securing the Connecting Cables ....................................................................... 15

Configuration and Management ........................................................................ 15

Fan Module ........................................................................................................ 16

Specifications ..................................................................................................... 17

Product Documentation Online .......................................................................... 17

Important Safety Instructions ............................................................................. 18

Warranty, Sales, Service, and Training Information ........................................... 20

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply

to the software and/or firmware (individually or collectively the “Software”)

incorporated into the Paradyne product (the “Product”) purchased by you and any

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

2July 2005 IPD4-A2-GZ40-10

derivatives obtained from the Software, including any copy of either. If you have

executed a separate written agreement covering the Software supplied to you

under this purchase, such separate written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to

accept a personal, non-transferable, non-exclusive, right (without the right to

sublicense) to use the Software, solely as it is intended and solely as incorporated

in the Product purchased from Paradyne or its authorized distributor or reseller

under the following terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors.

The Licensee acquires no title, right or interest in the Software other than the

license granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in

which the Product was rightfully purchased except upon prior written notice to

Paradyne and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the

Software in whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

5. Except for the Product warranty contained in the manual, the Software is

provided “AS IS” and in its present state and condition and Paradyne makes

no other warranty whatsoever with respect to the Product purchased by you.

THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES,

WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING

WITHOUT LIMITATION:

a. Any warranty that the Software is error-free, will operate uninterrupted in

your operating environment, or is compatible with any equipment or

software configurations; and

b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT

LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied

warranties on limitations on how long an implied warranty lasts, so the above

limitations may not apply to you. This warranty gives you specific legal rights,

and you may also have other rights which vary from one state or jurisdiction to

another.

6. In no event will Paradyne be liable to Licensee for any consequential,

incidental, punitive or special damages, including any lost profits or lost

savings, loss of business information or business interruption or other

pecuniary loss arising out of the use or inability to use the Software, whether

based on contract, tort, warranty or other legal or equitable grounds, even if

Paradyne has been advised of the possibility of such damages, or for any

claim by any third party.

7. The rights granted under this Agreement may not be assigned, sublicensed or

otherwise transferred by the Licensee to any third party without the prior

written consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be

terminated in the event of breach by the Licensee of any provisions of this

Agreement.

IPD4-A2-GZ40-10 July 2005 3

9. Upon such termination, the Licensee shall refrain from any further use of the

Software and destroy the original and all copies of the Software in the

possession of Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without

regard to its provisions concerning conflicts of laws.

Introduction

Paradyne's 4000E IP Broadband Loop Carrier (BLC) provides a high capacity and

native IP Ethernet foundation for a variety of feature-rich multi-service access

mulitplexer modules.

The 4000E BLC features a high capacity backplane delivering up to 8 Gbps

throughput, and providing a non-blocking architecture for even the highest

bandwidth broadband access technologies, such as ADSL2+. It supports a single

uplink, management, and switching module connected to the dual backplanes with

redundant modular backhaul/uplink ports to support 10/100 Ethernet, GigE

(copper or fiber), T1/E1, and dual bonded T1/E1 uplink modules.

The 4000E BLC is environmentally hardened for installation in Remote Terminals

or street cabinets. For flexibility of installation the 4000E BLC has removable

mounting brackets that can be placed in increments of 1.45” up to 9.28” from the

front of the chassis, allowing for multiple installation options in either 19" or 23"

equipment racks.

Unpacking and Inspecting the Equipment

HANDLING PRECAUTIONS FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage

due to electrostatic discharge (ESD) during normal operation. When

performing installation procedures, however, take proper static control

precautions to prevent damage to equipment. If you are not sure of the

proper static control precautions, contact your nearest sales or service

representative.

The following components should be included in the shipping container:

1 – 4000E BLC with 1 fan module and 12 slot covers

4 – Rubber Bumper Screws

4July 2005 IPD4-A2-GZ40-10

2 – Rack Mount Brackets (either 19" or 23", as ordered)

10 – #6 Phillips Bracket Screws

8 – #10 Phillips Rack Screws

8 – #12 Phillips Rack Screws

If there is visible damage, do not attempt to connect the device. Contact your sales

representative.

Installation Options

The 4000E BLC is designed for installation in a Restricted Access area where

admittance is limited to trained and authorized service personel. It may be

installed on a tabletop or in a rack.

Installation on a Tabletop

Insert the four provided rubber bumper screws into the mounting holes at the

bottom of the 4000E chassis for surface grip and airflow. Position and secure all

connecting cables such that they will not become a tripping hazard or pull loose

from the chassis. Ensure that the air supply vents around the top and bottom

edges of the chassis are not blocked.

4000E BOTTOM VIEW

RUBBER BUMPER

SCREW

Side Top

Front Rear

IPD4-A2-GZ40-10 July 2005 5

Installation in a Rack

Using a Phillips Screwdriver, attach the two [2] provided rack mount brackets to the

sides of the 4000E with eight [8] of the ten [10] provided bracket screws. There are

seven position options for the rack brackets; position them as best suited to the

space available for your chassis on the rack being utilized.

Mount the chassis onto the rack and secure the rack mount brackets to the sides

of the rack using one of the two provided sets of eight [8] rack screws (whichever

size fits the rack being utilized).

Check the rack for stability, ensuring that installation of the 4000E has not caused

the rack to become top-heavy.

RACK MOUNT

BRACKET 4000E SIDE VIEW

Front Rear

4000E FRONT VIEW

6July 2005 IPD4-A2-GZ40-10

Installing Your Management Module

A management module provides the functional control for the 4000E BLC; the

4000E cannot function without one. There are several different models available

for purchase. Refer to www.paradyne.com for further information, or contact your

sales representative.

Installing a Management Module

An uplink module provides the upstream network connection for the 4000E BLC; a

management module cannot function without one. Depending on the management

module model that you plan to install in your 4000E, you will need either a Media

Interface Module (MIM) or an Uplink Interface Module (UIM). Only one uplink

module is required for operational purposes. However, two uplink modules may be

installed, one in each port of the management module, if redundancy is desired.

Refer to your management module or uplink module installation instructions for

further information.

CAUTION

If a slot cover is removed from a management module uplink port, it must be

replaced with an uplink module. DO NOT OPERATE A 4000E WITH A

MANAGEMENT MODULE THAT HAS AN OPEN UPLINK PORT.

Procedure

1. Identify the appropriate slot for installation.

The 4000E is a five slot chassis: slots 1–4 are reserved for interface modules

and Slot U1 is reserved for a management module. The 4000E is shipped

from the factory with slots 1 and U1 open and ready for module installation.

2. Align the management module with the slot module guides. With the

management module printed circuit board (PCB) facing up and the

management module model name on the right side of the module faceplate

(facing towards you), align the left and right edges of the PCB with the U1 slot

module guides on the 4000E.

Management Module Slot

IPD4-A2-GZ40-10 July 2005 7

3. Slide the Management Module Firmly into the Chassis. Tighten the fastening

screws on the management module faceplate.

Installing Your Interface Module(s)

Interface modules provide the subscriber connections for a 4000E BLC; up to four

interface modules may be installed in the 4000E (in slots 1–4). There are a variety

of models available for purchase. Refer to www.paradyne.com for further

information or contact your sales representative. Any combination of interface

module models may be installed in an 4000E as long as they are supported by the

model type and version number of your management module; refer to the Release

Notes for your particular management module model.

CAUTION

If a slot cover is removed from slots 2–4, it must be replaced with an uplink

module. DO NOT OPERATE A 4000E WITH AN EMPTY MODULE SLOT.

MANAGEMENT MODULE

Slot Module Guides

Fastening Screws

8July 2005 IPD4-A2-GZ40-10

Procedure

1. Select a Slot for Installation.

Although the 4000E is factory shipped with Slot 1 open, interface modules

may be installed in any slot, 1–4.

2. Align the interface module with the slot module guides. With the interface

module PCB facing up and the interface module model name on the right side

of the module faceplate (facing towards you), align the left and right edges of

the PCB with the slot module guides of the chosen slot on the 4000E.

3. Slide the interface module fFirmly into the chassis. Tighten the fastening

screws on the interface module faceplate.

Slot Module Guides

INTERFACE MODULE

Fastening Screws

IPD4-A2-GZ40-10 July 2005 9

Powering Up Your 4000E BLC

CAUTION:

Turn your DC power source(s) OFF until you have completed connection of

the 4000E as outlined in the following sections.

Do not operate the 4000E without a ground connection.

Procedure

1. Connect a ground wire to the 4000E: Line up the 2-hole terminal lug of your

ground wire with the two holes on the small, unpainted section on the back of

your chassis. Secure the terminal lug to the chassis with two #10-32 screws.

2. Connect the Ground Wire to a Frame Ground. Ground wire connection can

vary from location to location, although typically all equipment in a Central

Office is grounded to a common copper bus.

3. Select a Terminal Block. Either terminal block on the back of the 4000E may

be used to power the chassis; only one terminal block is required for

operational purposes. The two terminal blocks on the 4000E are independent

feeds. Chassis power is supplied by only one terminal block at a time; the

second supply is a backup. The two terminal blocks do not load-share; each

terminal block must be supplied with adequate amperage to run the chassis

independently.

4000E REAR VIEW

Ground Connection for 2-Hole Terminal Lug

10 July 2005 IPD4-A2-GZ40-10

4. Select a terminal block. Using a Phillips Screwdriver, remove the upper screw

from the chosen terminal block (labeled "+" on the chassis). Slide the ring

terminal of your positive power lead around the shaft of the screw and insert

the screw into the same "+" terminal from which it was removed.

DC Terminal Blocks

Ring

Terminal

POSITIVE

POWER LEAD

DC POWER

TERMINAL

Positive (+)

Terminal

Inhaltsverzeichnis

Andere Paradyne Netzwerk-Hardware Handbücher

Paradyne

Paradyne 8310 MVLt Bedienungsanleitung

Paradyne

Paradyne JetFusion Integrated Access Device Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 3810 Bedienungsanleitung

Paradyne

Paradyne Fan Tray Assembly 8820-S3-900 Bedienungsanleitung

Paradyne

Paradyne FrameSaver 9120 Betriebsanleitung

Paradyne

Paradyne COMSPHERE 3610 Bedienungsanleitung

Paradyne

Paradyne HotWire 8800 DSLAM Bedienungsanleitung

Paradyne

Paradyne Hotwire 7996 Original Betriebsanleitung

Paradyne

Paradyne Hotwire 7995 Bedienungsanleitung

Paradyne

Paradyne Hotwire 8775 MSDSL Bedienungsanleitung

Paradyne

Paradyne JetFusion 2008 Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 3800PLUS Bedienungsanleitung

Paradyne

Paradyne 7510-A2-GB20-00 727 Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 3610 Bedienungsanleitung

Paradyne

Paradyne iMarc DSL 9720 CSU/DSU Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 3550 Series Bedienungsanleitung

Paradyne

Paradyne Hotwire 8784 Bedienungsanleitung

Paradyne

Paradyne Micro Interface Module MIM-2000F Bedienungsanleitung

Paradyne

Paradyne Comsphere 3510 Bedienungs- und Wartungshandbuch

Paradyne

Paradyne BitStorm 2600 Bedienungsanleitung

Paradyne

Paradyne JetFusion 2208 Bedienungsanleitung

Paradyne

Paradyne Hotwire 8785 Bedienungsanleitung

Paradyne

Paradyne 8540 Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 6700 Series Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung