PEERLESS PLT BLK Leitfaden
ISSUED: 04-23-02 SHEET #: 200-9361-9 12-28-05
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 6
Installation and Assembly - Solid•Point™Plasma Table Top Stand
Read through instruction sheet and check to make sure you have all parts before beginning assembly and installation.
You will need assistance to complete the final step in assembling the Table Top Stand.
TOOLS REQUIRED: Phillips head screwdriver and open end wrench.
Model: PLT BLK,
PLT UNL
Please read this information first
Maximum Load Capacity: 150 lb (68.2 kg)
Protected by U.S. Patent number 478,088.
ISSUED: 04-23-02 SHEET #: 200-9361-9 12-28-05
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 6
PLT BLK
PLT UNL
Description Qty. Part No.
Abase 1 600-1000
Bsupport box 1 200-1234
Ccover plate 1 200-1236
Dtiltplate 1 200-1546
Etilt bracket 1 200-1237
F5/16 - 18 x 2.0 black socket screw 4 520-1116
G.406 x .812 x .06 flat washer 4 540-9407
H5/16 - 18 nut 4 530-9306
IM5 x .8 x 6 mm phillips pan head screw 6 520-9504
JM8 x 1.25 x 16 mm socket screw 2 520-9527
K3/16 allen wrench 1 560-9713
Ladhesive felt race 1 570-1035
M1.5 OD x .403 x .0625 washer 1 540-1009
Nrace 1 560-0065
O#10 x 3/4 particle board screw 4 500-9006
Prubber grommet 2 530-9401
Qknob 1 560-1143
Radhesive feet 1 570-1034
Sfinishing cap 2 590-1123
TM10 x 1.5 x 17 mm socket serrated flange bolt 4 520-1105
Uallen wrench for M10 socket bolt 1 560-9716
Parts List
Note: Actual parts may appear slightly different than illustrated.
A
E
I
J
F
N
Q
O
P
R
L
S
T
U
K
H
G
C
B
D
Components (B, C & D) are pre-assembled for packaging, separate components
before step one.
M
Note: Do not attach felt race (L) to race (N) before step 3-5.
ISSUED: 04-23-02 SHEET #: 200-9361-9 12-28-05
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 6
I
Note: For cord management route cords through support
bracket before attaching cover plate where indicated.
Snap two grommets (P) into holes used for cord
management. Snap two finishing caps (S) into unused cord
management holes. Hook cover plate (C) over support box
(B) and fasten with six phillips screws (I).
C
CORD
MANAGEMENT
S
P
Lay support box (B) on flat,
non-scratch surface. Insert
base (A) into support box.
A
BH
G
F
B
Fasten with four sets of bolts, nuts and
washers (F,G,H). Hand tighten fasteners.
Then hang base just over edge of work
surface and tighten fasteners with allen
wrench while holding nuts with and open
end wrench.
ISSUED: 04-23-02 SHEET #: 200-9361-9 12-28-05
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 6
OPTIONAL: For 360° swivel, attach race as shown in step three. For no swivel, skip step three and attach
adhesive feet (R) at four corners and front edge of base. Set feet back off edges about 3 inches.
N
A
BOTTOM VIEW
LARGE
HOLE
TOP VIEW
FOUR
MIDDLE
HOLES
Locate four middle holes
on top of race (N) circled
in Top View.
Flip race over and align one of
four middle holes from top of
race with large hole on bottom
of race circled in Bottom View.
Align one large hole and middle
hole with one pilot hole in base (A)
and place race on base.
Thread one screw (O) into pilot hole in
base (A) leaving screw slightly loose.
N
O
A
Rotate bottom of race (N) 180° and align large hole
and middle hole with pilot hole. Fasten with one screw
(O) leaving slightly loose. Rotate race and fasten two
screws (O) at 90° intervals into remaining pilot holes,
then tighten all four screws. Finally remove sticky back
from adhesive felt race (L) and adhere to race (N).
O
Attach race (N) to bottom of base (A). Lay base on flat surface as shown in step 3-3.
N
N
DETAIL 1
LARGE
HOLE
DETAIL 2
MIDDLE
HOLE LARGE
HOLE
MIDDLE
HOLE
ISSUED: 04-23-02 SHEET #: 200-9361-9 12-28-05
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
5 of 6
ADAPTER
BRACKET
(PLASMA
NOTSHOWN)
D
9"
(229 mm)
SIDE VIEW BACK VIEW
9" MAX.
DISTANCE TILTPLATE
TILTPLATE
PLASMA
SCREEN
T
REFER TO ACCOMPANYINGinstruction sheet to attach adapter bracket to plasma.
Attach tilt plate (D) to adapter bracket (attached to plasma screen) using four screws (T). Attach tilt bracket (E) to tilt plate
(D) using two screws (J).
Note: Choose holes on tilt plate according to size of plasma screen. Note: There is a 9" maximum distance between
bottom of monitor and tilt plate shown in Side & Back View. Exceeding maximum distance may interfere with tilt.
ADAPTER BRACKET MAY
APPEAR DIFFERENT THAN
ILLUSTRATED
D
E
J
ADAPTER
BRACKET
(PLASMA
NOTSHOWN)
ISSUED: 04-23-02 SHEET #: 200-9361-9 12-28-05
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
6 of 6
Attach plasma/hook plate to support bracket (B).
INDICATOR
B
D
QM
KNOB ADJUSTS 5°
BACKWARDTILTAND
10° FORWARD TILT
NOTCH
TWO PEOPLE REQUIRED FOR THIS STEP,
ONEHOLDING EACHEND OFPLASMA.
Tilt plasma back, then carefully slide tilt plate
(D) into slots and lift up into support box. Level
plasma screen engaging notch in tilt plate (D)
with steel rod inside support box.
Tilt plate is secure on steel rod of support box when
hole is visible on indicator as shown in detail. To
ensure plasma is properly placed, plasma can be tilted
5° back and 10° forward. Thread knob (Q) with washer
(M) into tilt bracket (E) through slot in rear of support box.
STEEL ROD
©2005PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkandSolid•Pointisatrademark ofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
• Do not lift more weight than you can handle! Use additional man power to safely handle placement of the Plasma
Screen.
WARNING
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere PEERLESS Rack & Stand Handbücher
PEERLESS
PEERLESS A100IWBMOUNT Leitfaden
PEERLESS
PEERLESS MSA-301 Leitfaden
PEERLESS
PEERLESS PANA-85WM Leitfaden
PEERLESS
PEERLESS DS415 Leitfaden
PEERLESS
PEERLESS ACC 604 Leitfaden
PEERLESS
PEERLESS HDS-S Leitfaden
PEERLESS
PEERLESS Solid-Point PLB 1 Leitfaden
PEERLESS
PEERLESS SmartMount SA750P Leitfaden
PEERLESS
PEERLESS PLA 50-UNL Leitfaden
PEERLESS
PEERLESS HCW101 Bedienungsanleitung
PEERLESS
PEERLESS Vision-Point LCV 100 Leitfaden
PEERLESS
PEERLESS WSP700 Bedienungsanleitung
PEERLESS
PEERLESS IMC 18 Leitfaden
PEERLESS
PEERLESS Paramount PPF Leitfaden
PEERLESS
PEERLESS WSP 716 Bedienungsanleitung
PEERLESS
PEERLESS SmartMount SP740P Leitfaden
PEERLESS
PEERLESS FPZ-655 Leitfaden
PEERLESS
PEERLESS DMU50SM Leitfaden
PEERLESS
PEERLESS Slimline OP-LWB 530 Leitfaden
PEERLESS
PEERLESS SPK 811W Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
