PEERLESS DMU50SM Leitfaden

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-26-09 SHEET #: 125-9060-5 07-26-13

Max Load Capacity:125 lb (56.6 kg)

Installation and Assembly:

SLIDE OUT WALL MOUNT

Models: DMU50SM

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-26-09 SHEET #: 125-9060-5 07-26-13

Description Qty. Part #

Awall plate 1 125-1007

Bslide out plate 1 125-1005

Cadapter bracket 2125-1006

DM5 x 10 mm socket pin serrated washer head screw 4 510-1126

EM5 x 16 mm socket pin serrated washer head screw 1 510-1161

FM5 x 25 mm socket pin serrated washer head screw 2 510-1122

G4 mm allen wrench 1560-9646

H.219 ID x .5 X OD x .5 tall nylon spacer 1 540-1057

I#14 x 2.5 hex phillips wood screw 4 5S1-015-C03

JM3 x 8 mm phillips pan screw 4 520-1038

K#4 flat washer 4540-1049

L.219 ID x .5 X OD x .25 tall nylon spacer 4540-9413

M3/4 EMT nut 1 560-0049

Nlock and key (not shown) 1560-0755

Oconcrete anchor 4 590-0320

Parts List

Before you start check the parts list to insure all of the parts shown are included.

IMPORTANT: Read instruction sheet before you start installation and assembly.

NOTE: Some parts may appear slightly different than illustrated.

Security Adapter Bracket Fasteners

M4 x 12 mm (6)

(510-1079)

M5 x 12 mm (4)

(520-1064)

M5 x 25 mm (4)

(520-1122)

M6 x 12 mm (4)

(520-1050)

M6 x 25 mm (4)

(520-1211)

M8 x 15 mm (6)

(520-1068)

M8 x 40 mm (4)

(520-1152)

I.D. .34” (8.6 mm) (4)

(540-1059)

I.D. .22” (5.6 mm) (4)

(540-1057)

multi-washer (6)

(580-1036)

M6 x 20 mm (4)

(520-9554)

M6 x 30 mm (4)

(520-1067)

M8 x 25 mm (4)

(520-1101)

M4 x 25 mm (4)

(510-1082)

NOTE: The sorted-for-you™ fastener pack included was made specically for your product and may not contain all components.

DEFC

JK L

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-26-09 SHEET #: 125-9060-5 07-26-13

Installation to Wood Stud Walls

Use a stud nder to locate the edges of the stud.

Use of an edge-to-edge stud nder is highly

recommended. Based on its edges, draw a vertical

line down the stud’s center. Place wall plate (A)

on wall as a template. Mark the center of the four

mounting holes. Drill four 5/32” (4 mm) dia. holes

2-1/2” (65 mm) deep. Secure wall plate (A) to wood

stud using four #14 x 2-1/2” wood screws (I) as

shown.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is rmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an “edge to edge” stud nder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations.

WARNING

Secure four .219 ID x .5 X OD x .25 tall nylon spacer

(L) and four M5 x 10 mm socket pin serrated washer

head screw (D) to bottom of wall plate (A). Secure

one M5 x 16 mm socket pin serrated washer head

screw (E) and one .219 ID x .5 X OD x .5 tall nylon

spacer (H) to top of wall plate as shown below.

Skip to step 3 on page 5

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-26-09 SHEET #: 125-9060-5 07-26-13

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8” of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1” minimum from the side of the block. Cinder block must meet ASTM C-90 specica-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

Installation to Solid Concrete or Cinder Block

Make sure that wall plate (A) is level, use it as a

template to mark four mounting holes. Drill four

1/4” (6 mm) dia. holes to a minimum depth of

2.5” (64 mm). Insert anchors (O) in holes ush with

wall as shown (right). Place wall plate over anchors

and secure with #14 x 2.5” screws (I). Level, then

tighten all fasteners.

WARNING

• Always attach concrete anchors directly to load-

bearing concrete.

• Never attach concrete anchors to concrete covered

with plaster, drywall, or other nishing material. If

mounting to concrete surfaces covered with a nish-

ing surface is unavoidable, the nishing surface must

be counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when tight-

ening screws. If plaster/drywall is thicker than 5/8”,

custom fasteners must be supplied by installer.

WARNING

• Tighten screws so that wall plate is rmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

solid concrete

cinder block

Drill holes and insert anchors (I).

Place plate (A) over anchors (I) and secure with screws (F).

Tighten all fasteners.

concrete

surface

CUTAWAY VIEW

CORRECT

plaster/

drywall

concrete

INCORRECT

plaster/

drywall

concrete

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-26-09 SHEET #: 125-9060-5 07-26-13

Note: Lock will NOT function properly if lock parts are in wrong position.

Secure lock (N) into wall plate (A) by using parts (provided with lock) and 3/4” EMT nut (M) as shown.

Lock Installation

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-26-09 SHEET #: 125-9060-5 07-26-13

To prevent scratching the screen, set a cloth on a at, level surface that will support the weight of the screen. Place

screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.

Place adapter brackets (C) on back of screen, align to holes, and center on back of screen as shown below. Attach

the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers, and

spacers as shown in gure 4.1 or 4.2.

NOTE: Top and bottom holes on screen must always be used.

Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.

Installing Adapter Brackets

Notes:

• The number of fasteners used will vary,

depending upon the type of screen.

• Multi-washers and spacers may not be

used, depending upon the type of screen.

• Use the corresponding hole in the multi-

washer that matches your screw size.

• Tighten screws so adapter brackets are rmly attached. Do not tighten with excessive force. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don’t get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

NOTE: For at back screens proceed to step 4-1. For bump-out or recessed back screen skip to step 4-2.

MEDIUM HOLE FOR M5 SCREWS

SMALL HOLE FOR M4 SCREWS

LARGE HOLE FOR M6 SCREWS

MULTI-WASHER

NOTE: “X” dimensions should be equal.

CCENTER BRACKETS

VERTICALLY ON BACK

OF SCREEN

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-26-09 SHEET #: 125-9060-5 07-26-13

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2

for a full screen compatibility chart for this mount.

Begin with the shortest length screw, hand thread through multi-washer and adapter bracket (C) into screen as

shown below. Screw must make at least three full turns into the mounting hole and t snug into place. Do not over

tighten. If screw cannot make three full turns into the screen, select a longer length screw from the bafed fastener

pack. Repeat for remaining mounting holes, level brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2

for a full screen compatibility chart for this mount.

Begin with longer length screw, hand thread through multi-washer, adapter bracket (C) and spacer in that order

into screen as shown below. Screw must make at least three full turns into the mounting hole and t snug into

place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from

the bafed fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

For Flat Back Screen

For Bump-out or Recessed Back Screen

SCREEN g 4.2

ADAPTER BRACKET (C)

SCREEN

g 4.1

MULTI-WASHER

SCREW

4-2

4-1

If you have any questions, please call Peerless customer care at 1-800-865-2112.

MULTI-WASHER

ADAPTER BRACKET (C)

SCREW

SCREEN

SPACER

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-26-09 SHEET #: 125-9060-5 07-26-13

Mounting and Removing Flat Panel Screen

Hook adapter brackets (C) onto wall plate (A) as

shown in g. 5.1. Then slowly swing screen in as

shown. Tighten M5 x 25 mm socket pin serrated

washer head screws (F), using security allen

wrench (G), clockwise at least six times to prevent

screen from being removed as shown in g. 5.1.

Screen can be adjusted horizontally if desired.

NOTE: To lock the screen down, fully tighten M5 x

25 mm socket pin serrated washer head screws (F)

to wall plate as shown in cross section.

To remove screen from mount, loosen M5 x 25 mm

socket pin serrated washer head screws (F) and

swing screen away from mount, and lift screen off of

mount.

• Always use an assistant or mechanical lifting equipment to safely lift and position the at panel screen.

WARNING

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

g 5.2

g 5.1

Visit the Peerless Web Site at www.peerlessmounts.com ISSUED: 03-26-09 SHEET #: 125-9060-5 07-26-13

Secure media box to slide out bracket (B) using four #4 at washers (K) and four M3 x 8 mm phillips pan screws

(J) as shown in g. 6.1. Position the slide out plate (B) into wall plate (A) making sure that the edge of the slide

out plate (B) is inside spacers. Slide plate in until it is stopped by ange in top as shown in g. 6.2. Use nger

holes when sliding slide out bracket (B) in and out of wall plate (A).

g. 6.1 g. 6.2

MEDIA

BOX

SPACERS

FLANGE

Detail 1

FINGER

HOLES

Note: once slide out bracket (B) is in place use key (located with lock) to lock. Be sure to keep key in a safe place,

as you will not be able to remove the media box without it.

Peerless is a registered trademark of Peerless Industries, Inc.

All other brand and product names are trademarks or registered trademarks of their respective owners.

Inhaltsverzeichnis

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS Paramount PRT2X2 Bedienungsanleitung

PEERLESS

PEERLESS ACC-V800X Leitfaden

PEERLESS

PEERLESS LCT Series Leitfaden

PEERLESS

PEERLESS Solid-Point PLCM UN1 Leitfaden

PEERLESS

PEERLESS LWB375 Leitfaden

PEERLESS

PEERLESS Mobile Videowall Trolley PDVWM 2x2 46 55 L Leitfaden

PEERLESS

PEERLESS SUF650P and assembly Leitfaden

PEERLESS

PEERLESS A100IWBMOUNT Leitfaden

PEERLESS

PEERLESS LMAM1940 Leitfaden

PEERLESS

PEERLESS ESA746PU Leitfaden

PEERLESS

PEERLESS IM760P Leitfaden

PEERLESS

PEERLESS SmartMount RTFPA45 Leitfaden

PEERLESS

PEERLESS Paramount PSP2 Leitfaden

PEERLESS

PEERLESS Smartmount ST670 Leitfaden

PEERLESS

PEERLESS Vision-Point LCV 100 Leitfaden

PEERLESS

PEERLESS LCC 18 Leitfaden

PEERLESS

PEERLESS SF630P-S and assembly Leitfaden

PEERLESS

PEERLESS WSP820 Leitfaden

PEERLESS

PEERLESS SA761P Leitfaden

PEERLESS

PEERLESS PWS211 Leitfaden

PEERLESS

PEERLESS VPM 25-J Leitfaden

PEERLESS

PEERLESS IWB600-WB Bedienungsanleitung

PEERLESS

PEERLESS PARAMOUNT PSP2-S Leitfaden

PEERLESS

PEERLESS JMWS 30 Leitfaden

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung