PEERLESS PRS-KIT0811 Leitfaden
This product is UL Listed. It must be
installed by a qualified professional
installer.
R
Max ULLoad Capacity: 25 lb (11.3 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 06-02-05 SHEET #: 054-9124-6 07-10-09
Installation and Assembly:
Model: PRS-KIT0811, PRS-KIT1420, PRS-KIT2026
2 of 8 ISSUED: 06-02-05 SHEET #: 054-9124-6 07-10-09
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
•phillips screwdriver
•drill with 1/4", 3/8", and 5/32" drill bits
Table of Contents
Parts List..............................................................................................................................................................................3
Installation to Wood Joist Ceiling ..........................................................................................................................................4
InstallationtoConcreteCeiling .............................................................................................................................................5
InstallationofExtensionColumn...........................................................................................................................................6
Installing Projector Mount assembly to the Extension Column .............................................................................................7
InstallingProjectorAdapterPlate..........................................................................................................................................7
ProjectorAlignment ..............................................................................................................................................................8
Forcustomer care call(800)729-0307 or (708)865-8870.
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer service at 1-800-729-0307.
• Thisproduct should onlybeinstalled by aqualifiedprofessional.
• Makesure thatthesupporting surfacewillsafely supportthecombined loadofthe equipmentand all attachedhard-
wareandcomponents.
• Never exceed the Maximum UL Load Capacity of 25 lb (11.3 kg).
• If mounting to wood studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgeto edge" studfinderis highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrews firmly, but donotovertighten. Overtightening candamagetheitems, greatly reducingtheirholding
power.
WARNING
3 of 8 ISSUED: 06-02-05 SHEET #: 054-9124-6 07-10-09
K
H
F
I
Note: Actual parts may appear slightly different than illustrated.
J
CE
D
A
B
L
M
Description Qty. Part #
X
A
extension pipe 1 154-1025
X154-1032
X154-1034
XBadjuster tube 1 154-1028
XX 154-1030
XXX CM5 x .8 x 10 mm phillips screw 1 520-9250
XXX DM10 x 60 mm carriage bolt 1 580-1022
XXX EM10 center lock nut 1 530-9402
XXX Fprojector mount assembly 1 055-0604
XXX Hflat washer 2 540-1078
XXX I#14 x 2.5 phillips hex head wood screw 2 5S1-015-C03
XXX Jconcrete anchor 2 590-0097
XXX Kceiling plate 1 580-1042
XXX L#10-32 x 1/4"socket pin screw 1 520-1196
XXX M4 mm security t-wrench 1 560-1718
Parts List
PRS-KIT 0811
PRS-KIT 1420
PRS-KIT 2026
4 of 8 ISSUED: 06-02-05 SHEET #: 054-9124-6 07-10-09
Drill two 5/32" (4 mm) dia. holes to a minimum
depth of 2.5" (64 mm). Attach ceiling plate (K)
with two #14 x 2.5" (6 mm x 65 mm) wood
screws (I) as shown using 3/8" (10 mm) socket
wrench.Tighten woodscrews(I) so ceilingplate
(K) is firmly attached.
Skip to step 2 on page 6.
Installation to Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings
• Tighten wood screws so that ceiling plate is firmly
attached,butdonot overtighten. Overtightening can
damagethe screws, greatlyreducingtheirholding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the joist. The use of an "edge to edge" stud
finderishighly recommended.
WARNING
I
I
K
WOOD
JOIST
CEILING
5 of 8 ISSUED: 06-02-05 SHEET #: 054-9124-6 07-10-09
Installation to Concrete Ceilings
Drill two 1/4" (6 mm) dia. holes to a minimum depth of
2.5" (64 mm). Attach ceiling plate (K) using two
concrete anchors (J) and #14 x 2.5" wood screws (I)
as shown in Illustration A and 1, 2, and 3 (below).
Tightenallfasteners.
I
Illustration A
K
CONCRETECEILING
1
3
Drill hole and insert anchor
Place ceiling plate over anchor and secure with screw
After repeating step one tighten all fasteners
concrete
ceiling
I
I
2K
CUTAWAYVIEW
INCORRECT
concrete
metal
bracket
plaster/
drywall
CORRECT
concrete
metal
bracket
plaster/
drywall
• Tightenwoodscrews firmly, butdonot overtighten.
Overtighteningcandamage the bolt, greatlyreducing
itsholdingpower.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
• Concrete anchors are notintendedforattachmentto
concretewall covered withalayer of plaster,drywall,
orother finishing material.Ifmounting to concretewall
coveredwithplaster/drywallisunavoidable, plaster/
drywall (up to 5/8" thick) must be counterbored as
shown below. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
WARNING
J
J
J
J
6 of 8 ISSUED: 06-02-05 SHEET #: 054-9124-6 07-10-09
Attachthreadedendofadjustertube (B) tothreaded
fittinginceiling plate (K).Tightensecurelyaligning
slot in end of adjuster tube (B) with one of the holes
inthe sideof threaded fitting.Insert and tightenone
M5 x .8 x 10 mm phillips screw (C) to lock adjuster
tube(B)tothreadedfitting.
• Installer must verify that the ceiling will safely support
thecombined weight ofallattachedequipment and
hardware.
WARNING
• Adjuster tube (B) must befully threaded (sixor seven
fullturns) ontothreadedfitting inceilingplate and then
locked with screw (C).
WARNING
Slideextensionpipe(A)over adjuster tube (B)tothe
desired height. Attach with one M10 x 60 mm
carriagebolt (D)andlock nut (E).
Installation of Extension Column
K
B
A
D
E
C
7 of 8 ISSUED: 06-02-05 SHEET #: 054-9124-6 07-10-09
Installation to Extension Column
Screwprojector mountassembly(F) ontoextension column (A).Tightenswivel stop screwagainst extension column
using a phillips head screw driver. Note: Swivel stop screw is used to jam against threads of extension column (A) to
preventanyexcessmovementofprojectormountassembly(F).Donotovertightenscrew;overtighteningscrewwill
damagethreads making itdifficultto separate products.
F
SWIVELSTOPSCREW
BACKOF
MOUNT
A
Installation of Adapter Plate
Note:UseaccompanyingSpider™ UniversalAdapterPlate instruction to installtheadapterplate,before proceeding
with step 5.
Slide connection block of adapter plate with projector into projector mount assembly (F) as shown. Tighten captive
screw to secure projector to projector mount assembly (F).
CONNECTIONBLOCK
• Always use an assistant or mechanical lifting equip-
ment to safely lift and position the projector.
WARNING
Installation of Projector
ADAPTERPLATE
CAPTIVESCREW
F
FRONTOFMOUNT
8 of 8 ISSUED: 06-02-05 SHEET #: 054-9124-6 07-10-09
Projector AlignmentProjector Alignment
Projector AlignmentProjector Alignment
Projector Alignment
To adjust yaw (swivel): Loosen screw on projector mount assembly (F) indicated below until projector mount can
be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Loosen two screws on projector mount assembly (F) indicated
below. Tilt mount to desired position and retighten screws.
To adjust roll (side to side tilt): Loosen two screws on projector mount assembly (F) indicated below. Tilt mount
todesired position andretighten screws.
©2005PeerlessIndustries,Inc.Allrightsreserved.
PeerlessisaregisteredtrademarkandSmartmountisatrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (L) through projector mount
assembly (F) and into connection block as shown.
FCONNECTIONBLOCK
L
SCREWFORSWIVELSTOP
FSCREWSFORROLLADJUSTMENT
SCREWSFORPITCHADJUSTMENT
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere PEERLESS Rack & Stand Handbücher
PEERLESS
PEERLESS PARAMOUNT PT640 and assembly Leitfaden
PEERLESS
PEERLESS JMWS 30 Leitfaden
PEERLESS
PEERLESS PARAMOUNT PP740 Bedienungsanleitung
PEERLESS
PEERLESS LCT-202 Leitfaden
PEERLESS
PEERLESS SmartMount ST 630P Leitfaden
PEERLESS
PEERLESS DMU50SM Leitfaden
PEERLESS
PEERLESS IM740P Leitfaden
PEERLESS
PEERLESS PLA 60-UNL Leitfaden
PEERLESS
PEERLESS SmartMount D-FPF-320 Leitfaden
PEERLESS
PEERLESS SlimLine MOWV241/BK Bedienungsanleitung
PEERLESS
PEERLESS Smartmount ST670 Leitfaden
PEERLESS
PEERLESS Solid-Point PLCM UN1 Leitfaden
PEERLESS
PEERLESS WMJ 018 Leitfaden
PEERLESS
PEERLESS SAL730P Leitfaden
PEERLESS
PEERLESS PARAMOUNT PF640 Leitfaden
PEERLESS
PEERLESS PARAMOUNT PSP2-S Leitfaden
PEERLESS
PEERLESS PWMT300 Bedienungsanleitung
PEERLESS
PEERLESS Solid-Point PLB 1 Leitfaden
PEERLESS
PEERLESS PJF2-UNV Leitfaden
PEERLESS
PEERLESS CMJ450 Leitfaden
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
