PEERLESS SF630P-S and assembly Leitfaden

Max UL Load Capacity: 80 lb (36.3 kg)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07

Features:

• For 10" to 24" LCD flat panel screens

• Ultra-slim design holds the screen flat against the wall

Installation and Assembly:

SmartMount™ Universal Flat Wall Mount

for 10" - 24" LCD Flat Panel Screens

Models: SF 630P, SF 630P-S, SF 630, SF 630-S

This product is UL Listed. It must be

installed by a qualified professional

installer.

2 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07

Note: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

•studfinder("edgetoedge"studfinderisrecommended)

•phillipsscrewdriver

•drill

•1/4" bit for concrete and cinder block wall

•5/32" bit for wood stud wall

•level

Accessories

• Metal Stud Fastener Kit (ACC 215) (Not evalutated by UL)

• VideoConferencingShelf(ACC309)(Not evalutated byUL)

• Accessory Shelves (PM 600, PM 610) (Not evalutated by UL)

• Donot begin to install your Peerless product until you have read and understood the instructions andwarnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please

callPeerless customer careat 1-800-865-2112.

• Thisproduct should only be installed bya qualified professional.

• Makesurethat the wall will safely support the combined load of the equipment and all attached hardware and compo-

nents.

• Neverexceed the Maximum UL Load Capacity of 80 lb (36.3 kg).

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgeto edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrews firmly, butdonot overtighten. Overtightening candamage the items, greatly reducingtheir holding

power.

WARNING

Table of Contents

Parts List..............................................................................................................................................................................3

Installation to Single Wood Stud Wall...................................................................................................................................4

Installation to Solid Concrete or Cinder Block .......................................................................................................................5

Attaching Hook Bracket to Flat Panel Screen ......................................................................................................................6

InstallingandRemovingFlatPanelScreen ...........................................................................................................................7

Forcustomer care call (800) 865-2112 or (708) 865-8870.

3 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07

SF 630P SF 630P-S SF 630 SF 630-S

Description Qty Part # Part # Part # Part #

Awall plate 1 095-1320 095-4320 095-1320 095-4320

Bhook bracket 1 095-1321 095-4321 095-1321 095-4321

CM5 x 12 mm screw 2 520-1027 520-1027 520-1064 520-1064

DM4 x .7 x 10 mm phillips screw 4 504-9012 504-9012 504-9012 504-9012

EM4 x .7 x 20 mm phillips screw 4 504-9020 504-9020 504-9020 504-9020

F.198 ID x .313 OD x .437 H retaining spacer 4 590-5005 590-5005 590-5005 590-5005

G#14 x 2.5" hex head wood screw 2 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03

HAlligator® anchor 2 590-0097 590-0097 590-0097 590-0097

I4 mm allen wrench 1 560-1145 560-1145

Parts List

D E G HFC

4 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07

Installation to Single Wood Stud Wall

1Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based

on its edges, draw a vertical line down the stud’s center. Place wall plate (A) on wall as a template, making sure that

the two mounting holes are over the stud centerline. Level plate, and mark the center of the two holes. Drill two

5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using two #14 x 2.5"

wood screws (G) as shown.

Skip to step 2 on page 6.

• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and

components.

WARNING

• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highly recommended.

• Hardwareprovided is for attachment ofmount through standard thickness drywallor plaster into wood studs.Installers

areresponsible to providehardware for othertypes of mounting situations.

WARNING

5 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07

Installation to Solid Concrete or Cinder Block

1Make sure that wall plate (A) is level, use it as a

template to mark two mounting holes. Drill two 1/4"

(6 mm) dia. holes to a minimum depth of 2.5" (64

mm). Insert anchors (H) in holes flush with wall as

shown(right). Place wall plate over anchors and

secure with two #14 x 2.5" screws (G). Level, then

tightenall fasteners.

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware

and components.

WARNING

CUTAWAY VIEW

INCORRECT

concrete

surface

Drill holes and insert anchors (H).

CORRECT

Place plate (A)over anchors (H) and secure with screws (G).

Tighten all fasteners.

wall

plate

plaster/

drywall

concrete wall plate concrete

plaster/

drywall

• Always attach concrete expansion anchors directly to

load-bearingconcrete.

• Neverattach concrete expansionanchorsto concrete

coveredwith plaster,drywall, or otherfinishing mate-

rial.If mounting to concrete surfacescovered with a

finishingsurface isunavoidable, the finishingsurface

must be counterbored asshown below. Be sure

concreteanchors do not pull away from concrete

whentightening screws. If plaster/drywall is thicker

than 5/8", custom fasteners must be supplied by

installer.

WARNING

• Tighten screws so that wall plate is firmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

CINDERBLOCK

SOLID

CONCRETE

6 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07

Attaching Hook Bracket to Flat Panel Screen

ThreadM5 phillips screws (C) to hook bracket(B)

making the screws flush with bracket as shown in

figures2.1and2.2.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

*For screens with a hole

pattern in a pocket,

spacers (F) go between

hook bracket (B) and

screen.

FORVESA100MOUNTINGPATTERN:

Choosehole pattern as shown below. Attach hook

bracket (B) to back of screen using four M4 x 10 mm

screws(D)asshown below.

3FORVESA®75MOUNTINGPATTERN:

Choosehole pattern as shown below. Attach hook

bracket (B) to back of screen using four M4 x 10 mm

screws(D)asshown below.

*Note: If hole pattern is in a pocket, attach hook

bracket (B) to back of screen using four M4 x 20 mm

screws(E)and fourretaining spacers(F)asindicated

below.

fig. 2.1 fig. 2.2

7 of 7 ISSUED: 04-18-05 SHEET #: 201-9427-6 02-06-07

Hookscreen onto wall plate (A) figure 4.1. Tighten

M5 x 12 mm screws (C), shown in figure 4.2 and

detail 1.

Note: For security models, tighten M5 x 12 mm

screws (C) using 4 mm allen wrench (I)

Toremove screen frommount,loosen screws (C)

and lift screen off of mount.

Installing and Removing Flat Panel Screen

SCREEN

• Do not lift more weight than you can handle. Use

additionalman powerormechanical lifting equipment

to safely handle placement of the screen.

• Failure to lock hook bracket with screws (C) can

cause screen to come off mount if hit accidentally.

• Do not tighten screws with excessive force.

Overtighteningcan causedamage to mount. Tighten

screws to 20 in. • lb (2.26 N.M.) maximum torque.

CAUTION

WARNING

DETAIL 1

fig. 4.2

fig. 4.1

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS FPZ-600 Leitfaden

PEERLESS

PEERLESS FPZ-655 Leitfaden

PEERLESS

PEERLESS SPK 811W Bedienungsanleitung

PEERLESS

PEERLESS SmartMount D-FPF-320 Leitfaden

PEERLESS

PEERLESS MSA-301 Leitfaden

PEERLESS

PEERLESS SOLID-POINT PLCM1CP Bedienungsanleitung

PEERLESS

PEERLESS PED 410 Leitfaden

PEERLESS

PEERLESS A100IWBMOUNT Leitfaden

PEERLESS

PEERLESS IB40 Leitfaden

PEERLESS

PEERLESS Smartmount Leitfaden

PEERLESS

PEERLESS SR1G Leitfaden

PEERLESS

PEERLESS HCW201 Bedienungsanleitung

PEERLESS

PEERLESS SGLS01 Leitfaden

PEERLESS

PEERLESS RTLA-100 Leitfaden

PEERLESS

PEERLESS ACC-V800X Leitfaden

PEERLESS

PEERLESS DS246 Leitfaden

PEERLESS

PEERLESS SA761PU Leitfaden

PEERLESS

PEERLESS IBA1 Leitfaden

PEERLESS

PEERLESS DS 35 Leitfaden

PEERLESS

PEERLESS LCC 18 Leitfaden

PEERLESS

PEERLESS VPM 25-W Leitfaden

PEERLESS

PEERLESS PARAMOUNT PT640 and assembly Leitfaden

PEERLESS

PEERLESS DS-VL-H018 Leitfaden

PEERLESS

PEERLESS DMU50SM Leitfaden

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung