PEERLESS PED 410 Leitfaden

IMPORTANT! Read entire instruction sheet

before you start installation and assembly. Before you start check the parts list to make sure

all of the parts shown are included.

Installation and Assembly- Elevation Pedestal Stand Model:

PED 410, PED 510,

PED 610, PED 710,

TPD 3032, TPD 3536,

A057-1002 (PED 410 only) 1 tube

057-1003 (PED 510 only)

057-1004 (PED 610 only)

057-1005 (PED 710 only)

B4MD-10HS15K 1 base plate

C1390-472 3 fastener plate

D530-9401 2 rubber grommet

E540-9407 6 flat washer

F540-9424 6 M10 lock washer

G5S1-M10-A20 6 M10 x 20 mm screw

H5M9-381-H03 6 rawl bolt

part# qty. part part# qty. part

NOTE:Partsmayappear slighty different then illustated.

TPD trays (TPD 3032 & TPD 3536) can only be used with pedestals

(PED 410, PED 510, PED 610 & PED 710).

I540-9400 4 #10 flat washer

J505-9010 6 M5-.8 x 10 mm penta-pin

K2245-081 4 uni. clip

L510-9107 4 1/4-20 x 3/8 phil. RD HD

M095-1021 (TPD 3032 only) 1 support tray

095-1022 (TPD 3536 only)

N046-1002 1 back clamp

O104-1006 1 support plate

P046-1001 1 base ring

Q1390-471 4 support leg

R530-9306 8 5/16 nylock nut

S520-9211 8 5/16-18 x 1 hex screw

V510-9110 6 1/4-20 x 1” phil. bolt

W590-1037 12 glide

X590-1036 12 spacer

Y520-9258 4 #10 x 3/4 penta-pin

Z520-9249 1 penta-pin tool

Available Accessories:

Ratchet Belt (ACC 666)

Pedestals models: PED 410, PED 510, PED 610, PED 710 Tray models: TPD 3032, TPD 3536

ISSUED: 12-03-99 SHEET #: 057-9002-1 08-16-04

Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.

1 of 4

ISSUED: 12-03-99 SHEET #: 057-9002-1 08-16-04

Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.

2 of 4

Insert two rubber grommets (D) into two 1.5” dia. holes located on the side of the tube (A) (near the top and

bottom).

Position fastener plate (C) inside the tube (A) as shown. Attach base plate (B) using two buttonhead cap screws

(G),lockwashers(F),andflatwashers(E). Tighten securely. Repeat for tworemainingfastenerplates (C).

• For attachment to concrete floor only! All six concrete

expansion anchors must be used. Tighten to 420 in •

lb(47.6N.M.)torque.

WARNING

Mark and drill a 3/8" dia. hole to a minimum depth of 2" at mounting holes located around the base plate (B).

Attach the pedestal to the floor using six concrete expansion anchors (H).

ISSUED: 12-03-99 SHEET #: 057-9002-1 08-16-04

Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.

3 of 4

Snap twelve glides (W) around edge of base ring (P) as shown.

Attach support plate (O) to tube (A) using four screws (L). Then attach the leg (Q) to the bottom of the plate (O)

usingtwobolts(S)andhexheadnuts(R). Tightensecurely.REPEAT FOR THREEREMAININGSUPPORT

LEGS(Q).

Attach base ring (P) to support plate (O) using six 1/4-20 x 1” screws (V) and twelve spacers (X). Note: Cutouts

in base ring (P) must be positioned towards the back. If the plate in step 5 was positioned as noted, ring (P) will

hang off the plate in the back.

cutouts

Cutouts

NOTE: Plate “0” must be positioned

so that the holes in the plate are

closest to what will be the front of

the pedestal. The plate is not cen-

tered over the pedestal so when it is

positioned correctly, more will hang

off the back than the front.

ISSUED: 12-03-99 SHEET #: 057-9002-1 08-16-04

Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.

4 of 4

Attach TV/Support Tray (M) to Base

Ring (P) using back clamp (N) and two

M5 x .8 x 10 mm penta-pin self tapping

screws(J).Usepenta-pintool(Z) and a

1/4"drivertodrivescrews.

Using uni-clips (K) and M5 screws (J) (see instruction card in

fastenerpack),or#10x3/4penta-pinscrew(Y)andwashers

(I) (for attachment to mounting bosses if present), or a

combination of both, attach Support Tray (M) to TV bottom.

Attach at four places as close to the four corners of the TV

bottom as possible. Use penta-pin tool (Z) and a 1/4" driver to

drivescrews.

PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

• Always use an assistant or mechanical lifting equip-

ment to safely lift and position the television.

WARNING

Dieses Handbuch passt für folgende Modelle

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS PLCM 3 Leitfaden

PEERLESS

PEERLESS PJF2-UNV Leitfaden

PEERLESS

PEERLESS PLA 60-UNL Leitfaden

PEERLESS

PEERLESS SmartMount SP850-UNL Leitfaden

PEERLESS

PEERLESS SA761PU Leitfaden

PEERLESS

PEERLESS LCC 18 Leitfaden

PEERLESS

PEERLESS SmartMount D-FPF-320 Leitfaden

PEERLESS

PEERLESS MIS488 Leitfaden

PEERLESS

PEERLESS LWB375 Leitfaden

PEERLESS

PEERLESS HDS-S Leitfaden

PEERLESS

PEERLESS PLT BLK Leitfaden

PEERLESS

PEERLESS DS415 Leitfaden

PEERLESS

PEERLESS DST940 Leitfaden

PEERLESS

PEERLESS IMC 18 Leitfaden

PEERLESS

PEERLESS SUF650P and assembly Leitfaden

PEERLESS

PEERLESS Solid-Point PS 1 Leitfaden

PEERLESS

PEERLESS DS246 Leitfaden

PEERLESS

PEERLESS DST360 Leitfaden

PEERLESS

PEERLESS ACC517 Leitfaden

PEERLESS

PEERLESS HCACC503 Bedienungsanleitung

PEERLESS

PEERLESS HCACC502 Bedienungsanleitung

PEERLESS

PEERLESS WBK100-W Leitfaden

PEERLESS

PEERLESS SmartMount SA750P Leitfaden

PEERLESS

PEERLESS ACC-V800X Leitfaden

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung