PEERLESS FPZ-600 Leitfaden

Max Load Capacity For Floor Stand Only:

Two screens at 200 lb (90.7 kg) each

Max Load Capacity For Floor Stand With ACC 604:

Four screens at 200 lb (90.7 kg) each

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 02-14-06 SHEET #: 202-9099-2 06-16-06

Installation and Assembly:

Floor Stand

Model: FPZ-600

2 of 7 ISSUED: 02-14-06 SHEET #: 202-9099-2 06-16-06

Note: Read entire instruction sheet before you start installation and assembly.

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please

call Peerless customer care at 1-800-729-0307.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

• Never exceed the Maximum Load Capacity.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

WARNING

Accessories

• Carriage for Additional Screens (ACC 604)

Table of Contents

Parts List .............................................................................................................................................................................. 3

Assembling Floor Stand ........................................................................................................................................................ 4

Attaching Adapter Plate to Screen with VESA 100 Mounting Pattern ................................................................................... 5

Attaching Adapter Plate to Screen with VESA 200 Mounting Pattern ................................................................................... 5

Attaching Adapter Plate to Screen with VESA 200 x 200 Mounting Pattern ......................................................................... 6

Attaching Adapter Plate to PLP Adapter Bracket ................................................................................................................. 6

Installing Flat Panel Screen on Floor Stand .......................................................................................................................... 7

3 of 7 ISSUED: 02-14-06 SHEET #: 202-9099-2 06-16-06

For customer care call (800) 729-0307 or (708) 865-8870.

Description Qty. Part #

Abase 1 201-1037

Bcarriage 1 201-1020

Cmain tube 2 580-1159

Dadapter plate 2 201-1022

E5/16-24 x 1/4" set screw 8 520-9566

FM6 x 20 mm serrated washer head socket pin screw 4 510-9554

GM10 x 15 mm socket head screw 4 520-9262

HM6 x 12 mm phillips screw 4 520-1128

IM6 x 20 mm phillips screw 4 520-9402

JM6 x 30 mm phillips screw 4 510-9109

KM4 x 10 mm phillips screw 4 504-9012

LM4 x 20 mm phillips screw 4 504-9020

M.198" ID x .313" OD x .437" H retaining spacer 4 590-5005

N6 mm non-security allen wrench 1 560-9716

O4 mm security allen wrench 1 560-9646

Pbumper strip 1 570-1030

Parts List

I J

K L M

EFH

4 of 7 ISSUED: 02-14-06 SHEET #: 202-9099-2 06-16-06

Slide two main tubes (C) onto base (A) and secure

using four set screws (E) as shown in figure 2 and

detail 1. Tighten screws using 4 mm allen wrench (O).

Slide carriage (B) onto main tubes (C). Slide carriage to desired height and secure using four set screws (E) as

shown in figure 3 and detail 2. Tighten screws using 4 mm allen wrench (O).

Note: Orientation of "UP" arrow is critical.

ADETAIL 1

fig 2

fig 3

For some situations, bumper strip (P) may be

required to keep base (A) level. If so, cut bumper

strip (P) into five equal pieces and adhere one piece

to each corner and one piece to center of bottom

side of base (A).

Note: The pieces can also be used in other locations

on the base's bottom for other situations.

DETAIL 2

5 of 7 ISSUED: 02-14-06 SHEET #: 202-9099-2 06-16-06

Choose hole pattern as shown in figure 4.2. Attach

adapter plate (D) to back of screen using four M4 x

10 mm screws (K) as shown.

Note: Orientation of "UP" arrow is critical.

*Note: If screw (K) gets less than three threads of

engagement, attach adapter plate (D) to back of

screen using four M4 x 20 mm screws (L) and four

spacers (M) as indicated below.

Skip to step 5 on page 7.

AttachingAdapter Plateto Screen withVESA100 MountingPattern

• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not

tightly secured, damage may occur to screen or product may fail.

WARNING

*For screens with a

hole pattern in a

pocket, spacers (M)

go between adapter

plate (D) and screen. M

AttachingAdapter Plateto Screen withVESA200 MountingPattern

• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not

tightly secured, damage may occur to screen or product may fail.

WARNING

Choose hole pattern as shown in figure 4.1. Attach

adapter plate (D) to back of screen using four M4 x

10 mm screws (K).

Note: Orientation of "UP" arrow is critical.

Skip to step 5 on page 7.

fig 4.1

fig 4.2

6 of 7 ISSUED: 02-14-06 SHEET #: 202-9099-2 06-16-06

Choose hole pattern as shown in figure 4.3. Attach

adapter plate (D) to back of screen using four M6 x

12 mm screws (H) as shown.

Note: Orientation of "UP" arrow is critical.

*Note: If screw (H) gets less than three threads of

engagement, attach adapter plate (D) to back of

screen using four M6 x 20 mm screws (I). If screw (I)

still gets less than three threads of engagement, use

four M6 x 30 mm screws (J).

Skip to step 5 on page 7.

For screen compatibility please refer to the plasma interface list on our website www.peerlessmounts.com or call

customer care for a screen specific adapter bracket (PLP models).

GENERICADAPTER

BRACKET

AttachingAdapter Plate to Screen with VESA200 x 200 Mounting Pattern

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

AttachingAdapterPlate to PLPModelAdapterBracket

fig 4.3

fig 4.4

Note: Refer to PLP model adapter bracket instruction

sheet for attachment of adapter bracket to screen.

Choose hole pattern as shown in figure 4.4. Attach

adapter plate (D) to back of screen using four M10 x

15 mm screws (G) as shown. Tighten screws using

6 mm allen wrench (N).

Note: Orientation of "UP" arrow is critical.

7 of 7 ISSUED: 02-14-06 SHEET #: 202-9099-2 06-16-06

To install second screen, repeat steps four and five for back side of carriage (B).

To install additional screens, ACC 604 is required.

Hook adapter plate (D) onto carriage (B) and secure using two M6 x 20 mm serrated washer head socket pin screws

(F) as shown in figure 5 and detail 3. Tighten screws using 4 mm allen wrench (O).

DETAIL 3 fig 5

Peerless is a registered trademark of Peerless Industries, Inc.

All other brand and product names are trademarks or registered trademarks of their respective owners.

Inhaltsverzeichnis

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS Smartmount SWS310/BK Leitfaden

PEERLESS

PEERLESS DS-VW760 and assembly Leitfaden

PEERLESS

PEERLESS ACC 604 Leitfaden

PEERLESS

PEERLESS MSA-301 Leitfaden

PEERLESS

PEERLESS WSP700 Bedienungsanleitung

PEERLESS

PEERLESS HCW101 Bedienungsanleitung

PEERLESS

PEERLESS PLA 60-UNL Leitfaden

PEERLESS

PEERLESS PM 47 Leitfaden

PEERLESS

PEERLESS IB40 Leitfaden

PEERLESS

PEERLESS PTT188743 Series Bedienungsanleitung

PEERLESS

PEERLESS ESA746PU Leitfaden

PEERLESS

PEERLESS SMARTMOUNT SCS221 Leitfaden

PEERLESS

PEERLESS Solid-Point PLB 1 Leitfaden

PEERLESS

PEERLESS MOD-FPSKIT150 Bedienungsanleitung

PEERLESS

PEERLESS CMJ 470W Leitfaden

PEERLESS

PEERLESS PARAMOUNT PT650 and assembly Leitfaden

PEERLESS

PEERLESS PRG-1 Leitfaden

PEERLESS

PEERLESS Paramount PS200 Leitfaden

PEERLESS

PEERLESS PARAMOUNT PRA2X2 Bedienungsanleitung

PEERLESS

PEERLESS SmartMount ST 635 Leitfaden

PEERLESS

PEERLESS SmartMount ST 635 Leitfaden

PEERLESS

PEERLESS Mobile Videowall Trolley PDVWM 2x2 46 55 L Leitfaden

PEERLESS

PEERLESS PARAMOUNT PA730 Bedienungsanleitung

PEERLESS

PEERLESS Smartmount SA752P Leitfaden

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung