Pelonis HC-1010 Bedienungsanleitung

HC-1010

IMPORTANT INSTRUCTIONS

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances,basic precautions should always be followed to

reduce the risk of fire,electric shock,and injury to persons,including the following:

1. Read all instructions before using heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot

surface. If provided, always use handles when moving this heater. Keep

combustible materials such as furniture, pillows, bedding, papers, clothes and

curtains at least 3 feet (0.9m) from the front of the heater and keep them away

from the sides and rear.

3. Extreme caution is necessary when any heater is used by or near children or

invalids and whenever the heater is left operating and unattended.

4. Always unplug the heater when not in use.

5. Do not operate any heater with a damaged cord or plug or after the heater

malfunctions, has been dropped or damaged in any manner. Discard heater or

return heater to authorized service facility for examination, electrical or

mechanical adjustment, or repair.

6. Do not use the heater outdoors.

7. This heater is not intended for use in bathroom, laundry areas and similar moist

indoor locations. Never locate heater where it may fall into a bathtub or other

water container.

8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,

or similar coverings. Do not route cord under furniture or appliances. Arrange

cord away from traffic area and where it will not be tripped over.

CAUTION:

This appliance has a polarized plug (one blade is wider than the

other). To reduce the risk of shock, this plug is intended to fit only one way in a

polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it

still does not fit, contact a qualified electrician. DO NOT attempt to defeat this

safety feature. To do so could result in an electric shock hazard.

10. This heater draws 12.5 amps during operation. To prevent overloading a

circuit, do not plug the heater into a circuit that already has other appliances

working.

11.

CAUTION:

It is normal for the plug to feel warm to the touch; however, a loose

fit between the AC outlet (receptacle) and plug may cause overheating and

distortion of the plug. Contact a qualified electrician to replace loose or worn

outlet.

12. To disconnect the heater, first turn controls to off, then remove plug from

outlet. Never pull by the cord.

13. Do not insert or allow foreign objects to enter any ventilation or exhaust

opening as this may cause an electric shock or fire, or damage the heater.

14. To prevent a possible fire, do not block air intakes or exhaust in any manner.

Do not use on soft surface, like a bed, where openings may become blocked.

15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas

where gasoline, paint, or flammable liquids are used or stored.

16. Use this heater only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock, or injury to

persons.

17.

CAUTION:

Always plug heaters directly into a wall outlet/receptacle. Never

use with an extension cord or reloadable power tap (outlet/power strip).

18. The output of this heater may vary and its temperature may become intense

enough to burn exposed skin. Use of this heater is not recommended for

persons with reduced sensitivity to heat or an inability to react to avoid burns.

19. Disposal of oil contained within should be in accordance with applicable

regional, national, and local laws and regulations.

20.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF

PLUG TO WIDE SLOT AND FULLY INSERT.

21. “SAVE THESE INSTRUCTIONS”

STRUCTURAL SKETCH

Machine components

Control panel

Rear cover

Air outlet

Display

screen

Remote control

storage port

CHECK BEFORE STARTUP

USAGE

1. Whether the power cord is in good condition.

2. The power supply for the product is 120V AC, and the carrying capacity of the socket shall

not be lower than 12.5A. Otherwise, accidents may occur.

[Start the machine]

Plug in the power and press the ON/Standby button of the control panel to start the machine.

After starting, the machine will run in the previous mode.

"+" button

ON/Standby button

"-" button

Timing

button

Gear button

Oscillating

button Display window

Plug in the power, press the "ON/Standby" button to enter the ON mode, and the

heater starts to work. The whole machine runs at the previous mode and temperature.

Press the "On/Standby" button in the startup mode to enter the standby mode, and the

heater will stop working.

After starting up, press the "gear" button repeatedly, and the heater will switch

according to the recursive sequence of "energy-saving mode → breeze → low warm

air → high warm air".

Button Functional description

Under ON mode, press the button to turn on the oscillating head, and then press the

button to turn off the oscillating head.

Power/ Standby

button

Gear button

+/-

button

Timing button

Oscillating button

When the machine is in operation, press the "+" or "-" button toset the operating

temperature. The temperature setting range is 40 - 95°F, with an interval of 1°F

between adjacent temperature values. If there is no operation within 3 seconds after

setting, the set temperature value will be confirmed and displayed. When the room

tempe rature reaches the set temperature, the display screen flashes for 10s, and the

heating element stops working. When the temperature is lower than the set

temperature, the machine starts heating again.

Under ON mode, press the button to select the timing shutdown setting, the timing

indicator lights up, the temperature display icon goes out, and the display screen

flashes to display the remaining time set last time. The shutdown time can be set

through the "+" and "-" buttons, with the setting range of 0-24 hours. If there is no

button action within 5 seconds, it will confirm the timing time and exit the timing

setting state. If the set timing time is 0, it means to cancel the timing setting. If the set

timing time is not 0, the machine automatically shuts down and goes into standby

mode when the set time is reached, and the timing indicator is out. Set the timing time

again after setting the timing time, and the timing is also re-timed. In the standby

mode, you press the button to make reserved startup setting, and the operation is the

same as timed shutdown. Timer time unit is hour.

Screen-off function

When the machine is in the working state, the screen will go out automatically if there is no

operation for 1 minute, and only the operation mode logo will be kept on. Press and hold the " "

and "-" buttons for 2 seconds at the same time to turn off the screen extinguishing function, then

press and hold the " " and "-" buttons for 2 seconds at the same time again to turn on the screen

extinguishing function.

Short-circuit Temperature Control Sensor, Open Circuit Protection

In any mode, if the temperature limiter has short circuit and open circuit protection, and the digital

screen displays "E1" or "E2" and keeps flashing, pressing any button will not work. The buzzer

sounds 10 times.

Safety protection

Tip-over protection

When it is in the ON state and indoor ambient temperature Th is higher than 122°F, the system will turn

off all the outputs, the digital screen will display "FF" and flash at a frequency of 1 time/second; then,

pressing any button will not work, and the protection can only be withdrawn if the power is cut off.

Either in the ON or OFF state, when the machine dumps, the system will immediately turn off all

the heating components and display "E3"; then, pressing any button will not work.

Turn Off Buttons' Decorative Lights and Buzzers

In the ON state, press the "timing button" and "gear button" for 2 seconds at the same time to turn off

the output of the buttons' decorative lights and buzzers. Repeat the operation toturn on this function.

Child Lock

Either in the ON or OFF state, the child lock will be opened when you press and hold "+" and "-"

buttons simultaneously for 2 seconds for the first time. Repeat the operation to turn off this function.

Remote controller

Remote control usage: The key function is consistent with those on the operation panel. Note:

Press the "< >" button of the remote control to enter the highly warm air mode with one button.

ECO mode

In ECO mode, press "+, -" to set the required temperature. When the ambient temperature is lower

than the set temperature (lower than 4°F or above), the product will be heated in a highly warm air

state; when the ambient temperature is close to the set temperature (lower than 4°F), the product

will be heated in a lower warm air state; when the ambient temperature is higher than the set

temperature, the product will stop heating.

HC-1010 800 1500

MAIN PARAMETERS

Rated voltage: 120V ~ 60Hz

Model Power adjustment range

Low-gear High gear

TROUBLESHOOTING

Problem

After the power is

switched on, the power

indicator does not turn

on, and the machine

does not work.

Shutdown suddenly

occurs in heating

Possible cause

The plug is not plugged

in properly

The temperature exceeds

the threshold of the

temperature limiter.

Solutions

Check whether the plug is inserted in

the socket properly

Use it after the machine is cooled

If the product does not operate or does not operate properly, first check according to the following

list. If the reason the product does not operate or does not operate properly is not included in the

following list, the product mayhave failed. At this time, it is recommended to send the product to

the dealer for treatment.

1. Do not dispose of batteries in fire, batteries may explode or leak.

2. Do not mix old and new batteries.

3. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

4. Non-rechargeable batteries are not to be recharged.

5. Batteries are to be inserted with the correct polarity.

6. Exhausted batteries are to be removed from the product.

7. The batteries must be removed from the remote controller before it is scrapped

and that they are disposed of safely.

BATTERY WARNING

SERVICE & SUPPORT

Inhaltsverzeichnis

Andere Pelonis Heizung Handbücher

Pelonis

Pelonis HC-0113 Bedienungsanleitung

Pelonis

Pelonis NF15-9BMB Bedienungsanleitung

Pelonis

Pelonis HC-451 Bedienungsanleitung

Pelonis

Pelonis HC-0119A Bedienungsanleitung

Pelonis

Pelonis PSH700R Bedienungsanleitung

Pelonis

Pelonis HF-1003 Bedienungsanleitung

Pelonis

Pelonis NTH15-17MR Bedienungsanleitung

Pelonis

Pelonis HO-0221 Bedienungsanleitung

Pelonis

Pelonis CH1001 Bedienungsanleitung

Pelonis

Pelonis HC-0113 Bedienungsanleitung

Pelonis

Pelonis HO-202C Bedienungsanleitung

Pelonis

Pelonis PHTPU1501WC Bedienungsanleitung

Pelonis

Pelonis HF-0060 Bedienungsanleitung

Pelonis

Pelonis PSH700 Bedienungsanleitung

Pelonis

Pelonis Safe-T FURNACE HC-445 Bedienungsanleitung

Pelonis

Pelonis HT-0605 Bedienungsanleitung

Pelonis

Pelonis HF-0055 Bedienungsanleitung

Pelonis

Pelonis HC-0119A Bedienungsanleitung

Pelonis

Pelonis HB-215T Bedienungsanleitung

Pelonis

Pelonis PHT30D7BBC Bedienungsanleitung

Pelonis

Pelonis HF-0019 Bedienungsanleitung

Pelonis

Pelonis HO-158E Bedienungsanleitung

Pelonis

Pelonis NTK15A Bedienungsanleitung

Pelonis

Pelonis HF-0063 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung