Pepperl+Fuchs WCS-PNG110 Bedienungsanleitung

WCS-PNG110

WCS PROFINET

INTERFACE MODULE

FACTORY AUTOMATION

MANUAL

With regard to the supply of products, the current issue of the following document is appli-

cable: The General Terms of Delivery for Products and Services of the Electrical Industry,

published by the Central Association of the Electrical Industry (Zentralverband Elektrotech-

nik und Elektroindustrie (ZVEI) e.V.) in its most recent version as well as the supplementary

clause: "Expanded reservation of proprietorship"

WCS-PNG110

1 Introduction ................................................................. 4

2 Declaration of conformity........................................... 5

2.1 CE conformity ............................................................................................5

3 Safety ........................................................................... 6

3.1 Symbols relevant to safety .......................................................................6

3.2 Intended use ..............................................................................................6

3.3 General safety instructions ......................................................................6

4 Product description .................................................... 7

4.1 Use and application ..................................................................................7

5 Installation ................................................................... 8

5.1 Mounting ....................................................................................................8

5.2 Electrical connection ................................................................................8

6 Commissioning ......................................................... 10

6.1 Cable routing in the RS 485 bus ............................................................10

6.2 Meaning of LEDs .....................................................................................13

6.3 Connecting the reading heads ...............................................................14

6.4 Connecting the WCS-PNG110 to the network .......................................15

6.5 Adding WCS-PNG110 to the network.....................................................15

6.6 Request byte for reading heads.............................................................20

6.7 Data format of WCS-PNG110 interface module for the

reading heads ..........................................................................................20

7 Appendix.................................................................... 21

7.1 Meaning of F0 ..........................................................................................21

7.2 Data from reading head ..........................................................................21

7.3 Error codes ..............................................................................................22

20234 2 2 009-04

WCS-PNG110

Introduction

1 Introduction

Congratulations

You have chosen a device manufactured by Pepperl+Fuchs. Pepperl+Fuchs develops,

produces and distributes electronic sensors and interface modules for the market of

automation technology on a worldwide scale.

Symbols used

The following symbols are used in this manual:

Handling instructions

You will find handling instructions beside this symbol

Contact

If you have any questions about the device, its functions, or accessories, please contact us at:

Pepperl+Fuchs GmbH

Lilienthalstraße 200

68307 Mannheim

Telephone: +49 621 776-4411

Fax: +49 621 776-274411

E-Mail: fa-info@pepperl-fuchs.com

Note!

This symbol draws your attention to important information.

WCS-PNG110

Declaration of conformity

20234 2 2 009-04

2 Declaration of conformity

2.1 CE conformity

This product was developed and manufactured under observance of the applicable European

standards and guidelines.

Note!

A declaration of conformity can be requested from the manufacturer.

20234 2 2 009-04

WCS-PNG110

Safety

3 Safety

3.1 Symbols relevant to safety

3.2 Intended use

The WCS-PNG110 interface module serves as an interface between the WCS reading heads

and the PLC.

Read through these instructions thoroughly. Familiarize yourself with the device before

installing, mounting, or operating.

Always operate the device as described in these instructions to ensure that the device and

connected systems function correctly. The protection of operating personnel and plant is only

guaranteed if the device is operated in accordance with its intended use.

3.3 General safety instructions

The operator of the system is responsible in terms of planning, mounting, commissioning,

operating and maintenance.

Installation and commissioning of all devices must be performed by a trained professional only.

Independent interventions and separate modifications are dangerous and will void the warranty

and exclude the manufacturer from any liability. If serious faults occur, stop using the device.

Secure the device against inadvertent operation. In the event of repairs, send the device to

Pepperl+Fuchs.

Danger!

This symbol indicates a warning about a possible danger.

In the event the warning is ignored, the consequences may range from personal injury to death.

Warning!

This symbol indicates a warning about a possible fault or danger.

In the event the warning is ignored, the consequences may course personal injury or heaviest

property damage.

Caution!

This symbol warns of a possible fault.

Failure to observe the instructions given in this warning may result in the devices and any

connected facilities or systems develop a fault or fail completely.

Note!

Disposal

Electronic waste is hazardous waste. When disposing of the equipment, observe the current

statutory requirements in the respective country of use, as well as local regulations.

WCS-PNG110

Product description

20234 2 2 009-04

4 Product description

4.1 Use and application

The WCS-PNG110 interface module acts as an interface between the WCS reading head and

the PROFINET IO. Data is transferred between the reading head and the interface module via

an RS 485 interface. The data from the interface module to the PLC is transferred using the

PROFIBUS protocol. You can connect a maximum of four WCS reading heads Type LS221

(and/or LS121) to one WCS-PNG110 interface module. If you connect several reading heads,

they must have different addresses. The number of connected reading heads is configured in

the hardware project settings.

20234 2 2 009-04

WCS-PNG110

Installation

5 Installation

5.1 Mounting

The dimensions of the WCS-PNG110 interface module are:

23 x 111 x 115 mm (W x H x D).

The WCS-PNG110 interface module is attached to a 35 mm wide DIN mounting rail (EN 50022-

35) with a snap attachment.

The device is grounded via the mounting rail.

5.2 Electrical connection

Connector X1 is located on the top side of the interface module, connector X2 on the

underside.

Figure 5.1: Electrical connection

Note!

Grounding of the mounting rail

The mounting rail must be grounded to the switch cabinet. The connection wire must have a

cross section of at least 10 mm2.

Reading head

WCS.-LS221

WCS-PNG110

PROFINET

Interface

RS 485 -

RS 485 +

24 V (Pwr)

0 V (Pwr)

X2-1

X2-2

X1-4

X1-5

X1-6

X1-7

SUB

GND

SDA

SDB

GND UB+

PROFINET

Ethernet

RJ45

UB+

GND

RS 485+

RS 485-

Note!

To use with an RS 485 interface, terminal “Rx 422+”on connector X1 must be connected to

terminal "Tx 422+", and terminal "Rx 422-" must be connected to terminal "Tx 422-".

Terminal Designation

4Rx 422+ Data line RS 485+ to reading head

5Rx 422- Data line RS 485- to reading head

6Tx 422+

7Tx 422-

Table 5.1: Terminal X1

WCS-PNG110

Installation

20234 2 2 009-04

Preparing to use the RS 485 interface

1. Connect terminal 4 "Rx 422+" to terminal 6 "Tx 422+".

2. Connect terminal 5 "Rx 422-" to terminal 7 "Tx 422-".

Connecting the interface module to the voltage

Connect the operating voltage (10...30 V DC) to terminals 1 and 2 of the 4-pin connector X2 on

the interface module.

The "Power" LED lights up green.

Terminal Designation

1UB (Pwr) Operating voltage interface module/

operating voltage reading head

20 V (Pwr) Ground interface module/ground reading head

Table 5.2: Terminal X2

Caution!

Damage to the device

Connecting an alternating current can damage the device or result in it malfunctioning.

Connect interface module to direct current (DC).

20234 2 2 009-04

WCS-PNG110

Commissioning

6 Commissioning

6.1 Cable routing in the RS 485 bus

The data cable must always form an in-line connection between the first and the last node. This

in-line connection must end with a terminator.

The RS 485 terminators are integrated in the WCS reading heads and can be switched on and

off with the interface module.

If only one reading head is connected, one device is connected at the beginning and one

device is connected at the end of the data line.

Figure 6.1: Connection of one reading head

Reading head

Interface or control

(PLC)

Inhaltsverzeichnis

Andere Pepperl+Fuchs Steuereinheit Handbücher

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E-KE5-IL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICE1-8IOL-S2-G60L-V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-24.10.R Handbuch

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E2A-KE1P-S/E2 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-2V15B Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-2E-G11-I/U/PT100-F Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IRI-KHD2-4.RX Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-4E4A-G20-ZEJ/M2L-P7-GEB Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs SIL KFD0-RSH-1 Benutzerhandbuch

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E-KE1-S Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E4A-G20-ZEJ/M48L-P12 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-V15B Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs PSU-IDM160-BD-1D-J1-N0 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs EtherCAT WCS-ECG110 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs WCS-CG310 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-2E-KE5-IJL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICE11-8IOL-G60L-V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VU120 Referenzhandbuch

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E4A-G20-ZEJ/M3L-P9 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAZ-2E2A-G20-ZPA1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VU121 Referenzhandbuch

Pepperl+Fuchs

Pepperl+Fuchs LAL-SRW series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICE11-8IOL-G60L-V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IUT-F190-R4-V1 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung