Philips Avent DECT baby SCD498 Bedienungsanleitung

SCD498

ENGLISH 6

 15

 25

 34

 43

 52

 61

 71

 80

 89

 99

 109

 119

 128

 137

 146

Introduction

Philips Avent is dedicated to producing caring, reliable products that give parents the reassurance

they need.This Philips Avent baby monitor provides round-the-clock support by ensuring you can

always hear your baby clearly without any distracting noise.The DECT technology guarantees zero

interference from other wireless appliances and a clear signal between the baby unit and the parent

unit.

General description (Fig. 1)

ABaby unit

1 On/off button 3

2 ON light

3 Volume +/– buttons

4 Battery check light T

5 Nightlight

6 Nightlight button Q

7 PAGE button

8 Microphone

9 Adapter

10 Small plug

11 Battery compartment lid

12 Socket for small plug

13 Battery compartment

BParent unit

1 TALK button

2 LINK light

3 SENSITIVITY button

4 On/off button 3

5 Opening for belt clip and neck strap

6 Sound level lights

7 Volume +/– buttons

8 Battery check light T

9 Microphone

10 Loudspeaker

11 Battery compartment

12 Belt clip

13 Battery compartment lid

14 Neck strap

15 Adapter

16 Charger

17 POWER light

CTravel pouch

Important

Read this user manual carefully before you use the appliance and save it for future reference.

This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult

supervision and should not be used as such.

Check if the voltage indicated on the adapters of the baby unit and the charger corresponds

to the local mains voltage before you connect the baby unit and the charger.

Use and store the appliance at a temperature between 10°C and 40°C.

The appliance is suitable for mains voltages from 220 to 240V.

Do not expose the baby monitor to extreme cold or heat or to direct sunlight.

ENGLISH

Make sure the baby unit and the cord are always out of reach of the baby (at least 1 metre/3

feet away).

Never place the baby unit inside the baby’s bed or playpen.

Never cover the baby monitor with a towel or blanket.

Never immerse any part of the baby monitor in water or any other liquid.

Never use the baby monitor in moist places or close to water.

Except for the battery compartments, do not open the housing of the baby unit and parent

unit in order to prevent electric shock.

Only use the adapter supplied to connect the baby unit to the mains.

Only use the charger supplied to charge the parent unit.

The adapters contain a transformer. Do not cut off the adapters to replace them with other

plugs, as this causes a hazardous situation.

If the adapter of the baby unit is damaged, always have it replaced with one of the original

type in order to avoid a hazard.

If the charger or the adapter of the charger is damaged, always have the charger replaced

with one of the original type in order to avoid a hazard.

Always place non-rechargeable batteries of the correct type in the baby unit to avoid the risk

of explosion.Always use rechargeable batteries of the correct type for the parent unit.

Since continuous transmission is prohibited, you only hear your baby when it makes sounds.



This Philips Avent appliance complies with all standards regarding electromagnetic elds (EMF).

If handled properly and according to the instructions in this user manual, the appliance is safe to use

based on scientic evidence available today.

Preparing for use

Baby unit

You can use the baby unit from the mains or on batteries. Even if you are going to use the unit from

the mains, we advise you to insert batteries.This guarantees automatic back-up in case of mains

failure.

Mains operation

1 Put the small plug in the baby unit and put the adapter in a wall socket (Fig. 2).

Battery operation

The baby unit runs on four 1.5V R6 AA batteries (not included). We strongly advise you to use

Philips LR6 PowerLife batteries.

Make sure your hands and the unit are dry when you insert the batteries.

1 Turn the battery compartment lid to the left (ÁOPEN) with the palm of your hand. (Fig. 3)

2 Remove the lid.

3 Insert four 1.5V R6 AA batteries (Fig. 4).

Place two batteries on top of each other and make sure the + and – poles of the batteries

point in the right direction.

4 Put the battery compartment lid back onto the unit and turn it to the right (CLOSE ª) with

the palm of your hand to close it. (Fig. 5)

Note:When the batteries are running low, the battery check light (T) lights up red.

ENGLISH 7

Parent unit

Battery operation

The parent unit runs on two rechargeable 1.2V AAA NiMh batteries that are supplied with the

appliance.

Make sure your hands and the unit are dry when you insert the batteries.

1 Slide the battery compartment lid downwards to remove it (Fig. 6).

2 Insert the two rechargeable batteries (Fig. 7).

Make sure the + and – poles of the batteries point in the right direction.

3 Slide the battery compartment lid back onto the back of the parent unit until it locks into

position (‘click’) (Fig. 8).

4 Put the adapter in a wall socket and place the parent unit in the charger (Fig. 9).

The POWER light on the charger lights up.

5 Leave the parent unit in the charger until the batteries are fully charged



parent unit and let it charge continuously for at least 10 hours.

Charging normally takes 8 hours, but it takes longer when the parent unit is switched on

while charging.To keep the charging time as short as possible, switch off the parent unit

during charging.

The POWER light on the charger stays on, even when the batteries are fully charged.

When the batteries are fully charged, the parent unit can be used cordlessly for at least

24 hours.

Note:The operating time of 24 hours is based on the assumption that the baby unit transmits 25% of

the time and is in standby mode for the rest of the time (when the baby does not make any sound).

Note: When the parent unit batteries are charged for the rst time, the operating time is less than 24 hours.

The batteries only reach their full capacity after you have charged and discharged them four times.

Note:When the batteries are running low, the battery check light (T) ashes red. Place the parent unit

in the charger.

Note:When the parent unit is not in the charger, the batteries gradually discharge, even when the parent

unit is switched off.

Mains operation

1 Make sure you have inserted the rechargeable batteries in the parent unit

2 Put the adapter of the charger in the wall socket and place the parent unit in the charger

(Fig. 9).

The POWER light on the charger lights up.



1 Place the parent unit and the baby unit in the same room to test the connection (Fig. 10).

Make sure the baby unit is at least 1 metre/3 feet away from the parent unit.

2 Press and hold the on/off button 3on the baby unit for 2 seconds. (Fig. 11)

The nightlight lights up briey.

The ON light lights up.

3 Press and hold the on/off button 3on the parent unit for 2 seconds. (Fig. 12)

The sound level lights light up blue briey.

The battery check light (T) lights up red briey.

ENGLISH8

The LINK light ashes red briey and then starts to ash green while the parent unit tries to

establish connection with the baby unit.

The LINK light on the parent unit ashes green until connection has been established.

This takes up to 30 seconds.The LINK light on the parent unit then lights up green

continuously (Fig. 13).

If no link is established after 30 seconds, the LINK light on the parent unit ashes red and the

parent unit beeps from time to time.

4 Place the baby unit at least 1 metre/3 feet away from your baby (Fig. 14).

5 Position the parent unit within the operating range of the baby unit. Make sure it is at least

1 metre/3 feet away from the baby unit (Fig. 15).

For more information on the operating range, see section ‘Operating range’ below.

Operating range

The operating range of the baby monitor is 300 metres/900 feet in open air. Depending on the

surroundings and other disturbing factors, this range may be smaller. Indoors the operating range is

up to 50 metres/150 feet.

Dry materials Material thickness Loss of range

Wood, plaster, cardboard, glass

(without metal, wires or lead) < 30cm/12in 0-10%

Brick, plywood < 30cm/12in 5-35%

Reinforced concrete < 30cm/12in 30-100%

Metal grilles or bars < 1cm /0.4in 90-100%

Metal or aluminium sheets < 1cm/0.4in 100%

For wet and moist materials, the range loss may be up to 100%.

Features



1 Briey press the volume + and – buttons on the baby unit until the desired loudspeaker

volume for the baby unit has been reached (Fig. 16).

2 Briey press the volume + and – buttons on the parent unit until the desired loudspeaker

volume for the parent unit has been reached (Fig. 17).

Note: If you press the volume + and – buttons too long, the volume is not adjusted.

Note:You only have to adjust the baby unit volume when you use the talk function (see below).

Note: If the volume is set to a high level, the units consume more power.



You can set the microphone sensitivity of the baby unit to the desired level.You can only change the

microphone sensitivity when a connection between the baby unit and the parent unit has been

established, i.e. when the LINK light on the parent unit lights up green continuously.

1 Briey press the SENSITIVITY button on the parent unit (Fig. 18).

The sound level lights on the parent unit light up for approx. 2 seconds to indicate the

current sensitivity level.

2 Briey press the volume + and – buttons on the parent unit until the desired microphone

sensitivity level for the baby unit has been reached.

ENGLISH 9

Note: If you press the SENSITIVITY button and/or the volume + and – buttons too long, the microphone

sensitivity is not adjusted.

one light on = minimum sensitivity level

all lights on = maximum sensitivity level

Note:When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds and

therefore transmits more often.As a result, the units consume more power.



You can use the TALK button on the parent unit to talk to your baby (e.g. to comfort your baby).

1 Press and hold theTALK button and talk clearly into the microphone (Fig. 19).

2 Release the TALK button when you have nished talking.

Note:When you press theTALK button, you can no longer hear your baby.

Silent baby monitoring

1 Briey press the volume down (–) button on the parent unit until the volume is switched off

completely (Fig. 20).

The volume is completely switched off when all sound level lights are out.

As long as the baby unit does not detect a sound, all sound level lights on the parent unit are

out (Fig. 21).

When the baby unit picks up a sound, one or more sound level lights on the parent unit

come on.The louder the sound, the more lights come on.

Nightlight

1 Briey press the nightlight button Qon the baby unit to switch on the nightlight. (Fig. 22)

2 Press the nightlight button Q again briey to switch off the nightlight.

The nightlight dims gradually before it goes out completely.

Note: If you press the nightlight button Qtoo long, the nightlight does not come on or go out.

Tip: Switch off the nightlight when you operate the baby unit on batteries.This saves power.

Paging the parent unit

If you have misplaced the parent unit and its volume is switched off, you can use the PAGE button

on the baby unit to locate the parent unit.

1 Briey press the PAGE button on the baby unit (Fig. 23).

The parent unit automatically resets to medium volume level and produces a paging alert

tone.

2 To stop the paging alert tone, press the PAGE button again briey or press any button on the

parent unit.

Note: If you press the PAGE button too long, the parent unit does not produce the paging alert tone.



If the batteries of the parent unit are sufciently charged, you can take the unit with you inside and

outside the house if you attach the unit to your belt or waistband with the belt clip or if you hang it

round your neck with the neck strap.This allows you to monitor your baby while you are moving

around.

Connecting the belt clip

1 Insert the small pin on the back of the belt clip into the opening on the back of the parent

unit (1).Turn the belt clip to the left (2) until it locks into position (‘click’) (Fig. 24).

ENGLISH10

Inhaltsverzeichnis

Sprachen:

Andere Philips Babyphone Handbücher

Philips

Philips AVENT SCD585 Bedienungsanleitung

Philips

Philips SBCSC464 Bedienungsanleitung

Philips

Philips AVENT SCD833 Bedienungsanleitung

Philips

Philips SBC SC466/00 Bedienungsanleitung

Philips

Philips SCD870 Bedienungsanleitung

Philips

Philips AVENT SCD831 Bedienungsanleitung

Philips

Philips AVENT SCD525/00 Bedienungsanleitung

Philips

Philips AVENT SCD506/52 Bedienungsanleitung

Philips

Philips SBC SC477 DECT Bedienungsanleitung

Philips

Philips SCD488/05 Bedienungsanleitung

Philips

Philips Avent SCD480 Bedienungsanleitung

Philips

Philips SCD484 Bedienungsanleitung

Philips

Philips SCD489/05 Bedienungsanleitung

Philips

Philips Avent SCD620 Bedienungsanleitung

Philips

Philips SBC SC465/05 Bedienungsanleitung

Philips

Philips SBCSC477/05 Bedienungsanleitung

Philips

Philips Avent SCD506 Bedienungsanleitung

Philips

Philips AVENT SCD710 Bedienungsanleitung

Philips

Philips SCD535/60 Bedienungsanleitung

Philips

Philips SBCSC490/00 Bedienungsanleitung

Philips

Philips SBC SC467 Bedienungsanleitung

Philips

Philips AVENT SCD535 Bedienungsanleitung

Philips

Philips SCD465 Bedienungsanleitung

Philips

Philips SBC SC362 Bedienungsanleitung

Beliebte Babyphone Handbücher anderer Marken

Motorola

Motorola MBP15 Bedienungsanleitung

Oricom

Oricom Babysense 7 Bedienungsanleitung

Levana

Levana TW502 Bedienungsanleitung

Luvion

Luvion Essential Bedienungsanleitung

NUK

NUK Eco Control Video Display 550VD Bedienungsanleitung

Lorex

Lorex sweet peek mini Bedienungsanleitung

Mondevices

Mondevices MonBaby 2 Bedienungsanleitung

Famidoc

Famidoc FDBB-V2 Bedienungsanleitung

Graco

Graco iMonitor 2797 Bedienungsanleitung

babymoov

babymoov High Care A014001 Bedienungsanleitung

Ramili

Ramili RV1000 Bedienungsanleitung

Swann

Swann SW231-FLO Bedienungsanleitung

Badabulle

Badabulle Baby Online 300 m+ Bedienungsanleitung

Philips AVENT

Philips AVENT SCD526/00 Bedienungsanleitung

Uniden

Uniden Guardian UBR223 Bedienungsanleitung

Summer

Summer Day & Night 28470A Bedienungsanleitung

Ivation

Ivation Wireless Monitoring System Bedienungsanleitung

Levana

Levana Lila Bedienungsanleitung