Pickering 40-297A Bedienungsanleitung

pickeringtest.com

Issue 1.0 October 2022

40/42-297A User Manual

PXI/PXIe High Density Precision Resistor Module

Page (II) PXI/PXIe High Density Precision Resistor Module 40/42-297A

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

PXI/PXIe High Density Precision Resistor Module 40/42-297A

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) PXI/PXIe High Density Precision Resistor Module 40/42-297A

pickering

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

PXI/PXIe High Density Precision Resistor Module 40/42-297A

pickering

Technical Support and Warranty................................................III

Product Safety .............................................................................IV

Contents (this page)....................................................................V

Warnings and Cautions ..............................................................VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Functional Description..........................................................2.1

Guidance on Using the Module............................................2.2

Section 3

Installation....................................................................................3.1

Pre Operation Checks...........................................................3.1

Hardware Installation ............................................................3.2

Software Installation .............................................................3.2

Testing Operation ..................................................................3.3

Section 4

Programming Guide....................................................................4.1

Programming Options For Pickering PXI/PXIe Modules ...4.1

Module Architecture..............................................................4.2

Programming Module............................................................4.2

Using The Soft Front Panel ..................................................4.4

Section 5

Connector Information................................................................5.1

Section 6

Trouble Shooting .........................................................................6.1

Section 7

Maintenance Information............................................................7.1

Verication & Adjustment Procedure ..................................7.2

Verication Test Results .......................................................7.9

CONTENTS

Page (VI) PXI/PXIe High Density Precision Resistor Module 40/42-297A

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

PXI/PXIe High Density Precision Resistor Module 40/42-297A

pickering

Page (VII)

2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O

signals that may be present. Blanking panels are available to order from Pickering in a variety of

slot widths. If the product is not used in this manner for example by using an extender card then

additional care must be taken to avoid contact with exposed signals.

Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.

This module must not be used for the switching of Mains Circuits. For the switching of voltages up

to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must

be fully isolated from the Mains Circuit and the safety earth.

The host chassis must be correctly installed and be connected to mains or factory safety ground,

please refer to your chassis installation manual.

Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT

For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage

Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved

by a transformer in which the primary windings are separated from the secondary windings by

reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

PXI Switching

Module

Device

Under Test

Power

Supply

Power

Supply

Host Chassis

Secondary Circuit

Mains

Circuit

Mains

Circuit

Mains/Factory

Safety Ground

Page (VIII) PXI/PXIe High Density Precision Resistor Module 40/42-297A

pickering

Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page 1.1

PXI/PXIe High Density Precision Resistor Module 40/42-297A

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

Precision Resistor Module (Part No. 4x-297A) Available with

Between 3 & 18 Channels

The 40-297A (PXI) and the 42-297A (PXIe) provide a

simple solution for applications requiring accurate

simulation of resistive sensors. They are available

in a variety of resistance ranges and resolutions to

meet the needs of functional test systems and are

suitable for engine controller testing where resistive

sensors provide information such as temperature.

Additionally, resistor channels can be set as short or

open circuit to simulate a wiring or sensor fault.

Software control is simpliﬁed by the use of resistor value calls. The module uses the setting closest to the requested value, and

the user can interrogate the module to ﬁnd the actual resistance setting used.

A calibration cable can be attached to the module allowing a DMM to verify each channel. This considerably simpliﬁes the

checking of the module’s calibration. Veriﬁcation is performed with the UUT disconnected from the module.

The 4x-297A is available in 70 standard builds in each platform that suit the most

common applications:

• A narrow resistance range version with 9 or 18 channels.

• A medium resistance range version with 4 or 9 channels.

• A wide resistance range version with 3 or 6 channels.

For applications requiring greater resolution and accuracy, or to support veriﬁcation

with the UUT connected, consider the 40-260 series Precision Resistor Modules.

Updated Product Information

This product has been introduced as a “form & ﬁt” update to the 40-297, the

changes are to provide PXIe options, higher maximum voltage plus higher

resolution range expansion. Otherwise, the electrical performance of the 40-297 and

4x-297A families are very similar, the pinout and software are identical.

yAvailable as a PXI or PXIe Module

yHigh Density Resistor Simulation

yUp To 18 Channels in a One Slot Module

yResistance Resolution to 0.125 Ω

yValues From 1 Ω to 85.3 MΩ

yAccuracy of up to ±0.1 % ± Resolution

yShort and Open Simulation

ySimple Software Control Through Resistance Calls

yVISA & Kernel Drivers Supplied for Windows

yPXI Versions Supported by PXI or LXI Chassis

y3 Year Warranty

42-297A-150

PXIe Version

Channel 1

Switched Resistor

Open

Short

Channel 2

Switched Resistor

Open

Short

Channel 18

Switched Resistor

Open

Short

Channel 2

Switched Resistor

Open

Short

pickeringtest.com

4x-297A

PXI/PXIe High Density Precision Resistor

Issue 1.0 Oct 2022

Page 1.2 PXI/PXIe High Density Precision Resistor Module 40/42-297A

pickering

SECTION 1 - TECHNICAL SPECIFICATION

Soft Front Panel for Precision Resistor Modules

PXI/PXIe Part Number

(Number of Channels)

Resistance Range

Resolution

1Ω 10Ω 100Ω 1kΩ 10kΩ 100kΩ 1MΩ 10MΩ 100MΩ

40/42-297A-010 (18) 40/42-297A-110 (9) 0.125 Ω

40/42-297A-011 (18) 40/42-297A-111 (9) 0.25 Ω

40/42-297A-012 (18) 40/42-297A-112 (9) 0.5 Ω

40/42-297A-013 (18) 40/42-297A-113 (9) 1 Ω

40/42-297A-014 (18) 40/42-297A-114 (9) 2 Ω

40/42-297A-015 (18) 40/42-297A-115 (9) 4 Ω

40/42-297A-016 (18) 40/42-297A-116 (9) 8 Ω

40/42-297A-020 (9) 40/42-297A-120 (4) 0.125 Ω

40/42-297A-021 (9) 40/42-297A-121 (4) 0.25 Ω

40/42-297A-022 (9) 40/42-297A-122 (4) 0.5 Ω

40/42-297A-023 (9) 40/42-297A-123 (4) 1 Ω

40/42-297A-024 (9) 40/42-297A-124 (4) 2 Ω

40/42-297A-025 (9) 40/42-297A-125 (4) 4 Ω

40/42-297A-026 (9) 40/42-297A-126 (4) 8 Ω

40/42-297A-030 (9) 40/42-297A-130 (4) 0.125 Ω

40/42-297A-031 (9) 40/42-297A-131 (4) 0.25 Ω

40/42-297A-032 (9) 40/42-297A-132 (4) 0.5 Ω

40/42-297A-033 (9) 40/42-297A-133 (4) 1 Ω

40/42-297A-034 (9) 40/42-297A-134 (4) 2 Ω

40/42-297A-035 (9) 40/42-297A-135 (4) 4 Ω

40/42-297A-036 (9) 40/42-297A-136 (4) 8 Ω

40/42-297A-040 (6) 40/42-297A-140 (3) 0.125 Ω

40/42-297A-041 (6) 40/42-297A-141 (3) 0.25 Ω

40/42-297A-042 (6) 40/42-297A-142 (3) 0.5 Ω

40/42-297A-043 (6) 40/42-297A-143 (3) 1 Ω

40/42-297A-044 (6) 40/42-297A-144 (3) 2 Ω

40/42-297A-045 (6) 40/42-297A-145 (3) 4 Ω

40/42-297A-046 (6) 40/42-297A-146 (3) 8 Ω

40/42-297A-050 (6) 40/42-297A-150 (3) 0.125 Ω

40/42-297A-051 (6) 40/42-297A-151 (3) 0.25 Ω

40/42-297A-052 (6) 40/42-297A-152 (3) 0.5 Ω

40/42-297A-053 (6) 40/42-297A-153 (3) 1 Ω

40/42-297A-054 (6) 40/42-297A-154 (3) 2 Ω

40/42-297A-055 (6) 40/42-297A-155 (3) 4 Ω

40/42-297A-056 (6) 40/42-297A-156 (3) 8 Ω

4x-297A Precision Resistor Module Range

4x-297A

pickeringtest.com Page 2

PXI/PXIe High Density Precision Resistor

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pickering Steuereinheit Handbücher

Pickering

Pickering 40-582 Bedienungsanleitung

Pickering

Pickering 40-870 Bedienungsanleitung

Pickering

Pickering 40-545 Bedienungsanleitung

Pickering

Pickering 40-561A Bedienungsanleitung

Pickering

Pickering 40-584 Bedienungsanleitung

Pickering

Pickering SYSTEM 10 Bedienungsanleitung

Pickering

Pickering PXI 41-752 Bedienungsanleitung

Pickering

Pickering PXI 60-104 Bedienungsanleitung

Pickering

Pickering 40-527A Bedienungsanleitung

Pickering

Pickering 40-292 Bedienungsanleitung

Pickering

Pickering PXI 40-510 Bedienungsanleitung

Pickering

Pickering PXI 40-710 Bedienungsanleitung

Pickering

Pickering PXI 40-664A Bedienungsanleitung

Pickering

Pickering 40-553A Bedienungsanleitung

Pickering

Pickering 40-582A Bedienungsanleitung

Pickering

Pickering BRIC Series Bedienungsanleitung

Pickering

Pickering 40-580 Bedienungsanleitung

Pickering

Pickering SYSTEM 10 Bedienungsanleitung

Pickering

Pickering 40-884 Bedienungsanleitung

Pickering

Pickering 4 785C Series Bedienungsanleitung

Pickering

Pickering 41-761 Bedienungsanleitung

Pickering

Pickering 40-727 Bedienungsanleitung

Pickering

Pickering SYSTEM 10 Bedienungsanleitung

Pickering

Pickering 40-656A Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung