Polaris 2883455 Bedienungsanleitung

APPLICATION

Verify accessory fitment at Polaris.com.

IMPORTANT

This Wireless Remote Kit is intended for use with HD

4500 Lb. Winch Kit (PN 2882714).

BEFORE YOU BEGIN

Read these instructions and check to be sure all parts and tools are accounted for. Please retain these

installation instructions for future reference and parts ordering information.

KIT CONTENTS

This Kit includes:

REF QTY PART DESCRIPTION PART NUMBER

1 1 Receiver, Wireless -

2 4 Screw, Torx®Pan Head, High/Low - #14 X 0.75 7519731

3 1 Remote, Wireless -

4 1 Holder, Wireless Remote -

5 2 Screw, Torx®Pan Head, High/Low - #10 X 0.75 7512026

1 Instructions 9929286

Instr 9929286 Rev 01 2018-04 Page 1 of 5

P/N 2883455

WIRELESS REMOTE KIT

Instr 9929286 Rev 01 2018-04 Page 2 of 5

TOOLS REQUIRED

• Safety Glasses

• Drill

• Drill Bit: 1/8 inch (3 mm)

• Pliers, Push Pin Rivet

• Screwdriver Set, Torx®

• Socket Set, Metric

• Wrench Set, Metric

IMPORTANT

Your Wireless Remote Kit is exclusively designed for your vehicle. Please read the installation instructions

thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to

ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.

ASSEMBLY TIME

Approximately 20–30 minutes

NOTE

Additional time may be required for optional step, or to accommodate other accessories.

HARNESS DETAIL

WIRELESS RECEIVER qq:

REF PART DESCRIPTION WIRE

COLOR

PIN QTY/

GENDER

CONNECTS TO

1A Wireless Receiver - - Vehicle structure

1B Connector, Autostop Controller/

Contactor

-4 male Main vehicle harness breakout;

see instructions for detail

1C Connector, Wired Remote -4 female Wired remote socket; see

instructions for detail

Instr 9929286 Rev 01 2018-04 Page 3 of 5

INSTALLATION INSTRUCTIONS

1. Shift vehicle transmission into “PARK”. Turn

ignition key to “OFF” position and remove from

ignition switch.

2. Flip up passenger seat bottom, remove driver’s

seat and underseat storage compartment, then

disconnect black negative (-) cable from battery.

3. Gain access.

a. Remove hood.

b. Remove upper dash cupholder by removing

two push pin rivets A, then sliding cupholder

rearward. Retain rivets.

4. Install wireless receiver.

a. Install wireless receiver qto RH side of under-

hood liner using four screws w. Do not over-

tighten screws.

b. Route wireless receiver connectors 1B and 1C

rearward through firewall grommet into upper

dash compartment.

NOTE

See previous section, HARNESS DETAIL, for

connector identification.

c. Detach existing wired remote connector B

from main vehicle harness breakout connector

d. Join wired remote connector Bto wireless

remote connector 1C.

e. Join wireless remote connector 1B to main

vehicle harness breakout connector C.

5. OPTIONAL: Install wireless remote.

NOTE

Wireless remote can be stowed in any suitable

location. Holder ris not required.

a. Remove wireless remote efrom holder r.

Determine suitable mounting location for holder

with special attention to the following:

• Driver operation of vehicle (including travel of

controls, such as shift lever)

• Driver visibility

• Adequate clearance between holder

mounting fasteners and other vehicle

components on underside of mounting

surface

b. Using holder ras template, mark and drill two

1/8 inch (3 mm) holes into mounting surface.

IMPORTANT

Control drill depth to prevent damage to underlying

structure or components.

c. Install holder rusing two screws t. Do not

over-tighten screws.

d. Reinstall wireless remote into holder.

6. Restore access. See Step 3.

7. Reconnect black negative (-) cable to battery, then

reinstall under-seat storage compartment and

driver’s seat.

Instr 9929286 Rev 01 2018-04 Page 4 of 5

OPERATION

OPERATIONAL CHECK

Wireless remote allows winch operation from outside

the vehicle. If winch does not operate as described,

refer to the TROUBLESHOOTING section.

IMPORTANT

The winch operator is always responsible for using

the winch properly, as described in the “Winch User

Guide” included in the winch kit.

1. To turn wireless remote “ON”, depress and hold

power button for three seconds or until LED light

illuminates.

2. To extend rope, depress and hold the “OUT”

button. To recover rope, depress and hold the “IN”

button.

3. The wireless remote will automatically turn “OFF”

after 30 seconds of inactivity. To manually turn off,

depress and hold power button for three seconds

or until LED light extinguishes.

Instr 9929286 Rev 01 2018-04 Page 5 of 5

TROUBLESHOOTING

SYMPTOM POSSIBLE CAUSES RECOMMENDED SOLUTION

Dead vehicle

battery

Incorrect, damaged, or

corroded electrical

connections

Verify all winch electrical connections are per instruction

manual and free of damage and/or corrosion.

Winch will not

operate

Contactor not receiving

power

Turn vehicle key on.

Wireless remote not

powered on

Turn wireless remote on.

Incorrect, damaged, or

corroded electrical

connections

Verify all winch electrical connections are per instruction

manual and free of damage and/or corrosion.

Keyed power circuit

(orange wires) not

properly powered

Check 10A accessory circuit fuse for continuity; replace as

required.

Winch operates in

one direction only

Autostop fairlead not

properly connected

If winch operates only outward then ensure magnetic stop

(black rubber puck) is not touching autostop fairlead.

If winch operates inward even when magnetic stop is

touching fairlead then verify all winch electrical connections

are per instruction manual and free of damage and/or

corrosion.

Winch makes noise

but rope/cable does

not move

Contactor powered, but

not winch

If clicking sound is heard when winch control button is

depressed, but winch motor is silent, then verify electrical

connections between winch and contactor are free of

damage and/or corrosion.

If winch makes noise but does not move, verify winch is in

gear.

If winch is in gear, but winch still does not move, have a

dealer inspect the winch.

Winch operates too

slowly

Winch is improperly

loaded

Verify rope/cable is not binding on spool or fairlead.

Winch will not

change gears

Rope/cable is under

load

Changing gears while under load is intentionally difficult to

prevent accidental operation, which could lead to personal

injury or winch failure. Ensure rope/cable is under no tension,

and rope/cable is not binding on spool or fairlead. Briefly

operate winch, then attempt to shift again.

FEEDBACK FORM

A feedback form has been created for the installer to provide any comments, questions

or concerns about the installation instructions. The form is viewable on mobile devices

by scanning the QR code or by clicking HERE if viewing on a PC.

FEEDBACK FORM

FCC Statement:

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Inhaltsverzeichnis

Andere Polaris Autozubehör Handbücher

Polaris

Polaris 2881113 Bedienungsanleitung

Polaris

Polaris 2880612 Bedienungsanleitung

Polaris

Polaris 2883419 Bedienungsanleitung

Polaris

Polaris 2882353 Bedienungsanleitung

Polaris

Polaris HomeLink 2882082 Bedienungsanleitung

Polaris

Polaris 2880325 Bedienungsanleitung

Polaris

Polaris 2883687 Bedienungsanleitung

Polaris

Polaris 2882270 Bedienungsanleitung

Polaris

Polaris RIDE COMMAND Bedienungsanleitung

Polaris

Polaris 2882857 Bedienungsanleitung

Polaris

Polaris 2879976 Bedienungsanleitung

Polaris

Polaris 2879201 Bedienungsanleitung

Polaris

Polaris ToyotaLUXX Bedienungsanleitung

Polaris

Polaris NG60 Bedienungsanleitung

Polaris

Polaris 2879954 Bedienungsanleitung

Polaris

Polaris BT50 Luxx Bedienungsanleitung

Polaris

Polaris PROSPECTOR PRO Bedienungsanleitung

Polaris

Polaris 2877466 Bedienungsanleitung

Polaris

Polaris 2016 RZR 4 900 Bedienungsanleitung

Polaris

Polaris 2879719 Bedienungsanleitung

Polaris

Polaris RW-50/15 Bedienungsanleitung

Polaris

Polaris RideCommand Bedienungsanleitung

Polaris

Polaris 2878839 Bedienungsanleitung

Polaris

Polaris 2880411 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung