Polaris 2883687 Bedienungsanleitung

APPLICATION

Verify accessory fitment at Polaris.com.

BEFORE YOU BEGIN

Read these instructions and check to be sure all parts and tools are accounted for. Please retain these

installation instructions for future reference and parts ordering information.

KIT CONTENTS

This Kit includes:

REF QTY PART DESCRIPTION KIT PN

2883687

KIT PN

2883786

1 1 Harness - 850 2414491 2414491

2 1 Harness - Titan -2414584

3 1 Harness - 600/800 2414585 2414585

4 1 Bag - HB USB Charge 2688874

2688951

1 Instructions 9928802 9928802

Instr 9928802 Rev 01 2018-06 Page 1 of 8

P/N 2883687; 2883786

HANDLEBAR BAG WITH PHONE CHARGER

KIT

Instr 9928802 Rev 01 2018-06 Page 2 of 8

TOOLS REQUIRED

• Safety Glasses

• Pliers, Push Pin Rivet

• Pliers, Side Cutting

• Socket Set, Metric

• Socket Set, Torx®Bit

• Torque Wrench

• Wrench Set, Metric

IMPORTANT

Your HANDLEBAR BAG WITH PHONE CHARGER KIT is exclusively designed for your vehicle. Please read the

installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of

debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the

sequence shown.

ASSEMBLY TIME

Approximately 30 minutes

NOTE

Additional time may be required for optional steps, or

to accommodate other installed accessories.

INSTALLATION INSTRUCTIONS

CAUTION

BEFORE STARTING INSTALLATION, always

ensure vehicle is properly secured on a flat stable

surface to avoid accidental tipping, unwanted

movement and to prevent personal injury and/or

damage to equipment. Turn key to “OFF” position

and remove from vehicle.

NOTE

Images shown may vary from your specific model

vehicle. Installation steps are similar between

models unless otherwise specified.

1. REMOVE SIDE PANELS.

2. REMOVE HOOD.

a. Slightly lift the rear of the hood assembly to

gain access to the main hood harness

connector Aand disconnect from main

chassis harness connector B. If applicable, cut

the cable tie Csecuring the hood harness to

the chassis and remove hood.

Instr 9928802 Rev 01 2018-06 Page 3 of 8

3. REMOVE UPPER INTAKE PLENUM.

a. To do so, first remove the two dart clips Aand

cable tie Bthat fasten the intermediate intake

tube Cto the upper intake plenum..

b. Next, unplug the two electrical connectors D

from the ECU E.

c. Remove the two screws Fthat attach the

upper intake plenum Hto the over-structure

along with the two dart clips Gas shown. Once

complete, remove upper intake plenum H.

Instr 9928802 Rev 01 2018-06 Page 4 of 8

4. REMOVE CONSOLE.

a. Remove two dart clips Aon right side along

with clutch tool Band dart clip Cfrom left side

and slide the console rearward leaving the

starter rope attached.

The console should now be in a position to

allow you to access the fabric electrical

connections bag in the following steps.

5. SELECT HARNESS.

a. For 850 models use harness q. See detailed

image.

• Connector (1a) will get connected to the

chassis harness.

• Connector (1b) is a spare connector for use

with additional accessories.

• Connectors (1c) connect to the USB

terminals on the bag.

b. For Titan

™™

models use harness w. See

detailed image.

• Connector (2a) will get connected to the chassis

harness.

• Connector (2b) is a spare connector for use with

additional accessories.

• Connectors (2c) connect to the USB terminals on

the bag.

Instr 9928802 Rev 01 2018-06 Page 5 of 8

c. For 600/800 models use harness e.

• Connector (3a) will get connected to the chassis

harness.

• Connector (3b) is a spare connector for use with

additional accessories.

• Connectors (3c) connect to the USB terminals on

the bag.

6. MOUNT HANDLEBAR BAG.

a. Ensure the USB harness connections are

connected to USB terminals on the back of the

bag. Place bag into position as shown.

b. Place bag over top of handlebars being sure

wires are routed downward along the

handlebar post.

c. Secure bag onto handlebars with the two hook

and loop fastener panels on each side of bag.

Instr 9928802 Rev 01 2018-06 Page 6 of 8

7. ROUTE AND CONNECT HARNESS WIRES.

NOTE

Electrical connections and routing vary slightly

between models. Follow steps for you specific model

for proper installation.

a. 850 Models

i. Route USB harness wires down along

steering post to the electrical connections

bag Blocated under the console.

Open bag and connect USB harness

connection (1A) to chassis harness

connector Cas shown.

b. Titan Model

i. Route USB harness wires down along

steering post to the electrical connections

bag Blocated under the console. Open

bag and connect USB harness connection

(2A) to chassis harness connector Cas

shown.

c. 600/800 Models

i. Route USB harness wires down along

steering post then along the left hand over-

structure tube to connector Clocated near

the left hand shock tower. Connect USB

harness connection (3A) to chassis harness

connector Cas shown.

Instr 9928802 Rev 01 2018-06 Page 7 of 8

8. REINSTALL CONSOLE.

a. Place console into original position and install

previously removed dart clips Aon right side

along with the clutch tool Band dart clip Con

left side.

9. REINSTALL UPPER INTAKE PLENUM.

a. Carefully install upper intake plenum Aback

into original position. Ensure the console tabs

Bare fully engaged into the slots Con the

underside of the intake plenum.

NOTE

Be careful not to damage the intake screen while

installing upper intake plenum.

b. Install dart clips Dand fasteners Ethat

secure the intake plenum Ato the over-

structure and torque fasteners Eto

specification provided

TORQUE

7 ft. lbs. (10 Nm)

Instr 9928802 Rev 01 2018-06 Page 8 of 8

c. Place intake tube Fback into position and

secure with previously removed dart clip

fasteners G. Replace cable tie Hto secure

lower portion of intake tube.

IMPORTANT

Ensure the mating joint between the upper intake

plenum and the intake tube is completely engaged

all the way around the mating joint. Failure to do so

may result in premature engine failure.

d. Reconnect ECU by plugging the chassis

electrical harness connector Jin the ECU K.

10.REINSTALL HOOD.

a. Install hood being sure to connect the hood

harness Aand chassis harness Bconnection.

Replace cable tie Cif applicable. Secure hood

into position with hood latch fasteners.

11. REINSTALL SIDE PANELS.

a. After installing hood, install both side panels

making sure all hood latches and rubber straps

are fully secured.

12.VERIFY WORK.

a. Check to ensure all tools are accounted for and

all steps have been completed.

FEEDBACK FORM

A feedback form has been created for the installer to provide any comments, questions

or concerns about the installation instructions. The form is viewable on mobile devices

by scanning the QR code or by clicking HERE if viewing on a PC.

FEEDBACK FORM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Polaris Autozubehör Handbücher

Polaris

Polaris SPORTSMAN PRO HD 2882242 Bedienungsanleitung

Polaris

Polaris 2016 RZR 4 900 Bedienungsanleitung

Polaris

Polaris 2879373 Bedienungsanleitung

Polaris

Polaris 2884764 Bedienungsanleitung

Polaris

Polaris NG60 Bedienungsanleitung

Polaris

Polaris 2879953 Bedienungsanleitung

Polaris

Polaris 2879954 Bedienungsanleitung

Polaris

Polaris 2878839 Bedienungsanleitung

Polaris

Polaris 2882271 Bedienungsanleitung

Polaris

Polaris CM50 Bedienungsanleitung

Polaris

Polaris 2880411 Bedienungsanleitung

Polaris

Polaris 2879201 Bedienungsanleitung

Polaris

Polaris 2882857 Bedienungsanleitung

Polaris

Polaris RIDE COMMAND Bedienungsanleitung

Polaris

Polaris 2879976 Bedienungsanleitung

Polaris

Polaris RIDE COMMAND Bedienungsanleitung

Polaris

Polaris 2880290 Bedienungsanleitung

Polaris

Polaris 2877466 Bedienungsanleitung

Polaris

Polaris 2876958 Bedienungsanleitung

Polaris

Polaris 2882353 Bedienungsanleitung

Polaris

Polaris RW-50/15 Bedienungsanleitung

Polaris

Polaris FR-1516 Bedienungsanleitung

Polaris

Polaris 2883455 Bedienungsanleitung

Polaris

Polaris HomeLink 2882082 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung