Polaris TR36P Bedienungsanleitung

OWNER’S MANUAL

English |Français |Español

H0570700_REVC

TR36P

English

USE OF THE POLARIS CLEANER IN A VINYL LINER POOL

Certain vinyl liner patterns are particularly susceptible to rapid surface wear or pattern removal caused by objects coming

into contact with the vinyl surface, including pool brushes, pool toys, floats, fountains, chlorine dispensers, and automatic

pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded simply by rubbing the surface with a pool

brush. Ink from the pattern can also rub off during the installation process or when it comes into contact with objects in the

pool. Zodiac Pool Systems, Inc. is not responsible for, and the Limited Warranty does not cover, pattern removal, abrasion

or markings on vinyl liners.

To avoid risk of potentially serious injury:

• Do not handle the Polaris cleaner while it is operating, except when checking the wheel RPM.

• Always remove the Polaris cleaner before swimmers enter the pool.

For customer service or support:

• Please mail warranty card immediately.

• For on-line support: www.polarispool.com

• To contact Polaris: US and Canada

Customer Service

2620 Commerce Way

Vista, CA 92081-8438

1-800-822-7933

CAUTION

Before You Start: Important Information

• Before installing the Polaris®cleaner, make sure the pool filter is clean.

• New plumbing lines should be flushed out before installing the Polaris cleaner.

• The Polaris cleaner should not be used to remove plaster dust in new pools.

• Always disconnect the cleaner before cleaning or backwashing the pool filter.

• After cleaning or backwashing, let the filtration system run for at least five (5) minutes before

reconnecting the cleaner.

• Always remove the cleaner from the pool before chemical shock treatements, such as super oxidation or

chlorination.

• Solar heating systems, ozone generators, and other air inducing equipment may cause air flow through the

cleaner, adversely affecting cleaner balance and performance. Plumb the dedicated cleaner line upstream

of these components.

• Highly chlorinated water can cause maintenance problems. Avoid running the Polaris cleaner while

chlorinating.

WARNING

English

• Scissors or garden shears

• Pliers

• Tape measure

Included in the Box

Tools Needed for Installation

• Piece of tape

• UWF tool (optional part # 10-102-00)

a. Cleaner Body

b. All-Purpose Zipper Bag

c. Head Float

d. Sweep Hose

e. Tail Sweep PRO®

(with Sweep Hose Scrubber)

f. Feed Hose

g. Hose Float(s)

h. Back-up Valve

i. Quick Disconnect and

Pressure Relief Valve

j. Universal Wall Fitting (UWF®)

k. Filter Screen, UWF/QD

l. Bag Collar

m. Pressure Tester

n. Bonus All-Purpose Zipper Bag

English

Installing the Cleaner

Read the complete owner’s

manual before you begin installation.

1 Prepare the Pool

1. Turn on the filtration pump for 2-3 minutes to flush out the plumbing lines.

2. Turn off the filtration pump.

3. Lay hose (f) out on the pool deck in sunlight to relax coils. This will reduce

the risk of tangling during cleaning.

2 Install the Universal Wall Fitting

Purpose of installing the UWF®:Once the UWF is properly installed, the Quick

Disconnect can be removed each time without removing the UWF.

1. Remove the Universal Wall Fitting (UWF) (j) from the end of the hose (f) and

thread (by hand) into the dedicated return line opening in the pool.

2. Make sure the filter screen (k) is firmly seated in the Quick Disconnect (i).

3. Install Quick Disconnect into the UWF by turning clockwise (do not over-tighten),

then pull to secure in place.

English

If your pool has two or three return lines, use the Eyeball

Fitting Connection Kit (part #9-100-8001). This kit

provides a Universal Wall Fitting (UWF®) and pressure

relief valve to be installed into the 2nd return line. Also

included is an eyeball regulator, which will replace the

existing eyeball if a 3rd return line is present.

Use the UWF Eyeball Fitting Kit (part

#6-511-00) to restore proper water

circulation when the cleaner is removed

from the pool.

If the pool does not have a dedicated return line, the Polaris TR36P cleaner connects to most common

return lines using special adapter kits available for purchase at a participating Polaris dealer.

For pools with plastic-pipe return lines (without pipe threads) that are cut off flush with the pool wall:

1" Stub Pipe Connection Kit

(part #9-100-8002)

1" Return Line

1" Expansion

Connector

If pipe is 1″ in

diameter, use 1″ Stub

Pipe Connection Kit

(part #9-100-8002)

1-1/2" Stub Pipe Connection Kit

(part #9-100-8003)

1-1/2"

Expansion

Connector

1-1/2" Return Line

If pipe is 1-1/2″ in

diameter, use 1-1/2″

Stub Pipe Connection

Kit (part #9-100-8003)



Does current fitting

look like this?

Connector

Head

Retainer

Ring



Wall Fitting 

Adapter



Eyeball Adapter Connection Kit

(part #9-100-8005)

For directional eyeball

fittings that do not

have a 1-1/2” threaded

socket, request the

Eyeball Adapter

Connection Kit (part

#9-100-8005)

Pool/Spa Connections Requiring Special Fittings

If a spa is connected to the pool filtration equipment, obtain expansion regulators in addition to one of the

kits listed above. Contact your dealer or Customer Service to determine which parts may be necessary.

Installing Other Pool Connections

Eyeball Regulator

Pressure

Relief Valve

Universal Wall Fitting

(UWF) O-Ring

Eyeball Connector

Eyeball Regulator

Retainer Ring

If the UWF and Eyeball

Regulators still cannot be

installed on the pool, contact

your dealer or Customer Service

to determine which parts may be

necessary.

Multiple Return Lines? Polaris®Cleaner Removed from Pool?

English

3 Test Water Pressure

4 Adjust Hose Length

1. Turn on the filtration pump.

2. With the hose connected to the UWF®, hold

the pressure tester (o) under water. Cover the

large hole with your thumb and confirm water is

releasing from the pressure

relief valve (i).

NOTE: There are two holes in the end of the pressure

tester. It is important to block the larger hole to verify

pressure.

1. Turn the pump on. Hold hose

under water until the pressure

relief valve releases pressure.

2. Extend the hose to the

farthest point of the pool.

The hose end must be within

6 inches (15 cm), longer or

shorter.

3. Measure the hose with the

pressure on and cut excess

length from the first hose

section (p). (This is the

section connected to the

Quick Disconnect (i).)

4. Reconnect hose sections.

5. After adjusting the hose

length, position the three

hose floats as shown.

No water flow from pressure relief valve?

• If your Polaris®cleaner is connected to a dedicated cleaner line, adjust the diverter valve to

increase the water flow to the cleaner.

• Make sure filter screen (k) is correctly positioned in Quick Disconnect.

• Check skimmer, pump basket, and main filter for debris restricting flow.

• If the Polaris cleaner is connected to one of multiple return lines, verify you have the correct

Polaris return line connection kits installed (see page 5 of this manual).

Hose too short?

• Contact your local Polaris dealer. Buy a new hose section. Add to

the first hose section (p) and cut until within 6 inches (15 cm).

6 in (15cm)

Recommended

Recommandé

Recomendado

Float (g)

Flotteur (g)

Flotador (g)

7ft (2.13m)

4ft (1.2m)

English

5 Assemble the Cleaner

1. Remove the pressure tester (o) by unscrewing the hose nut (q).

NOTE: The hose nut has reversed threads.

2. Use the same hose nut (q) and secure the hose to the cleaner body at the

feed pipe.

3. Pull the bag up and attach to the hose using the bag clip (n) .

4. Push the head float (c) all the way forward, up against the

cleaner body.

English

Before operating the Polaris cleaner®, check for proper wheel revolutions per minute

(RPM). For maximum efficiency, the Polaris should operate between 28 and 32

RPM.

1. Mark the single side wheel using using a piece of tape (or a small leaf tucked

into the tire).

2. Turn the pump on, hold the cleaner below the water level and count wheel

revolutions for one minute.

3. Optimum wheel speed should be between 28 and 32 RPM.

Operating the Cleaner

1. Connect hose in the pool at the UWF®.

2. Submerge the cleaner in the pool, allowing it to sink to the bottom.

3. Turn on the filtration pump and allow it to prime. Cleaner will begin to move.

1 Start the Cleaner

2 Check for Proper Wheel RPM

WARNING

To avoid risk of potentially serious injury, do not swim or use the pool

when the cleaner is submerged or operating.

mark the single

side wheel

(leaf, tape, or

marker)

Single-wheel Side

Sweep Hose

1 min

28 - 32 RPM

IMPORTANT

Keep cleaner

submerged for

accurate wheel

speed count.

mark the single side

wheel (tape or small leaf)

English

3 Adjust the Wheel Speed

• Check the filter screen in the Quick Disconnect for debris.

• Clean the skimmer, filter and pump basket.

• Check the hoses, connections, and swivel for leaks.

• If the cleaner is connected to a dedicated return line, adjust the diverter

valve to increase water flow.

Wheel Speed less than 28 RPM?

Wheel Speed more than 32 RPM?

• If the cleaner is connected to a dedicated cleaner line, adjust the diverter

valve to reduce the water flow to the cleaner.

• Unscrew the pressure relief valve until proper RPM is reached.

NOTE: For easier removal, use the Polaris®UWF®removal tool (Contact

your local Polaris dealer, Part # 10-102-00).

English

When operating correctly, the Polaris®cleaner vacuums, sweeps and scrubs all surfaces

randomly throughout the pool. The climbing ability depends on the pool’s shape and water

pressure or flow. The Polaris cleaner climbs best in pools without sharp angles or curves

in the transition from the pool floor to the pool wall. Approximately every 3-1/2 minutes the

Polaris cleaner goes into back-up mode. This action pulls the Polaris cleaner away from pool

obstacles.

The sweep hose should move in a gentle sweeping motion. To increase or

decrease sweeping motion:

1. Turn the filtration pump OFF.

2. Turn the adjustment screw on the feed pipe (r) counterclockwise to

increase sweep hose motion. Turn the adjustment screw clockwise to

decrease motion.

Decrease

motion Increase

motion

If the cleaner is veering left or right instead of tracking straight, adjust the

thrust jet (on the back of the cleaner body) for climbing walls or turning.

Fine Tuning the Cleaner

1 Adjust the Sweep Hose

2 Adjust the Thrust Jet

Fine tune your cleaner by adjusting the sweep hose or the

thrust jet as necessary, for optimal operation.

NOTE: Factory default setting is

eleven o’clock. Only adjust thrust

jet to accomodate unique pools

shapes.

Inhaltsverzeichnis

Sprachen:

Andere Polaris Staubsauger Handbücher

Polaris

Polaris 7240 Sport Bedienungsanleitung

Polaris

Polaris PVC 0750 Bedienungsanleitung

Polaris

Polaris PVCS 1101 HandStickPro Bedienungsanleitung

Polaris

Polaris WI-FI IQ Home Aqua PVCR 0735 Bedienungsanleitung

Polaris

Polaris PVCR 0833 WI-FI IQ HOME Bedienungsanleitung

Polaris

Polaris 9100 Sport Bedienungsanleitung

Polaris

Polaris 9400 Sport 4WD Bedienungsanleitung

Polaris

Polaris PVCS 5090 Clean Expert PRO Bedienungsanleitung

Polaris

Polaris 9300 Sport Bedienungsanleitung

Polaris

Polaris 340 Bedienungsanleitung

Polaris

Polaris 3900 Sport Bedienungsanleitung

Polaris

Polaris SmartGo PVCR 0930 Bedienungsanleitung

Polaris

Polaris PVCR 3300 IQ Home Aqua Bedienungsanleitung

Polaris

Polaris PVC 0730 Bedienungsanleitung

Polaris

Polaris P93 Bedienungsanleitung

Polaris

Polaris 9650iQ Sport Bedienungsanleitung

Polaris

Polaris PVCS 7090 HandStick PRO Aqua Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Bedienungsanleitung

Polaris

Polaris PVCR 3000 Cyclonic PRO Bedienungsanleitung

Polaris

Polaris PVCR 1026 Bedienungsanleitung

Polaris

Polaris PVCS 4000 HandStick PRO Bedienungsanleitung

Polaris

Polaris PVCR 1028 WI-FI IQ Home Bedienungsanleitung

Polaris

Polaris PVC 0786 Bedienungsanleitung

Polaris

Polaris 93 Series Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch