PolyScience LX Immersion Circulator Bedienungsanleitung

110-874 PSC/EN 25 February 2014

LX Immersion Circulator

Operator’s Manual

110-874 1

Table of Contents

Introduction ........................................................................ 2

General Information............................................................ 3

General Safety Information................................................ 3

Safety Recommendations.................................................. 4

Regulatory Compliance and Testing .................................. 5

Unpacking Your Immersion Circulator................................ 6

Package Contents ............................................................. 6

Controls and Components ................................................. 7

Installation and Startup...................................................... 9

Normal Operation ............................................................. 10

Buttons and Controls....................................................... 10

Turning Your Circulator ON.............................................. 10

Main Operational Displays................................................11

Set-Up Sub-Menus.......................................................... 12

Adjusting the Temperature Set Point................................ 13

Selecting the Temperature Unit ....................................... 13

Setting and Using the Timer ............................................ 14

Loss of Power Restart ..................................................... 14

Alarm Messages ............................................................. 15

Routine Maintenance and Troubleshooting..................... 15

Maintaining Clear Bath Water.......................................... 15

Cleaning Your Immersion Circulator ................................ 16

Resetting the Over-Temperature Safety........................... 17

Troubleshooting Chart ..................................................... 17

Technical Information....................................................... 19

Performance Specifications............................................. 19

Reservoir Fluids .............................................................. 19

Equipment Disposal (WEEE Directive) ............................ 20

Service and Technical Support ........................................ 21

Warranty............................................................................ 21

2110-874

WARNING: Circulating Baths are not intended

for directly controlling the temperature of foods,

pharmaceuticals, medicines or other objects which

may be ingested by or injected in humans or animals.

Any such objects must be isolated from contact with

the bath fluids and bath surfaces.

Introduction

Thank you for choosing the LX Immersion Circulator. It is

intended for the precise temperature control of suitable liquids in

a reservoir.

Here are some of the features of the LX Immersion Circulator:

• Simple, intuitive operation

• Displays actual and set point temperature simultaneously

• Powerful pump

• Attaches securely to both flat and rounded tank walls

• Converts any tank or vessel up to 20 liters into a reliable

circulating bath

• Fully enclosed housing prevents direct contact with pump and

heater

• Suitable for use with Class I non-flammable fluids per DIN

12876-1

We recommend that you read the Operator’s Manual thoroughly

before you begin.

110-874 3

This symbol alerts you to a wide range of potential

dangers.

General Information

When installed, operated and maintained according to the

directions in this manual and common safety procedures,

your LX Immersion Circulator should provide safe and reliable

liquid heating. Please ensure that all individuals involved in

the installation, operation or maintenance of this unit read this

manual thoroughly prior to working with the unit.

General Safety Information

Read all instructions pertaining to safety, set-up and

operation. Proper operation and maintenance is the

user’s responsibility.

This symbol advises of danger from electricity or

electric shock.

This symbol indicates a protective conductor

terminal.

This symbol marks information that is particularly

important.

This symbol indicates that a hot surface may be

present.

This symbol indicates alternating current.

These symbols on the Power Switch indicate that

they place the main power supply ON/OFF.

4110-874

Safety Recommendations

To prevent injury to personnel and/or damage to property,

follow your workplace’s safety procedures when operating

this equipment. You should comply with the following safety

recommendations:

WARNING:

• This Immersion Circulator is suitable only for use

with Class I non-flammable fluids

(per DIN 12876-1).

• Be aware of the chemical hazards that may be

associated with the bath fluid used. Observe all

safety warnings for the fluids used as well as those

contained in the material safety data sheet.

• Use only recommended bath fluids.

• Use only non-acid bath fluids.

• Use fluids that satisfy safety, health and equipment

compatibility requirements.

WARNING:

• Connect the power cord on this unit to a properly

grounded power outlet. Make certain that the outlet

is the same voltage and frequency as your unit.

• Never operate the unit with a damaged power cord.

• The use of an extension cord is not recommended.

• Turn the unit OFF and disconnect mains power

before performing any maintenance or service.

WARNING:

• Never operate the Circulator without bath fluid in

the reservoir. Periodically check the reservoir to

ensure that the liquid depth is within acceptable

levels. Refill the reservoir using the same bath

fluid that is already in the reservoir. Bath oil must

not contain any water contaminants and should be

preheated to the actual bath temperature before

adding as there is an explosion hazard at high

temperatures.

• Drain all fluid from the reservoir before moving

or lifting. Be sure to follow your organization’s

procedures and practices regarding the safe lifting

and relocation of heavy objects.

• Turn electrical power to the unit OFF and remove

the Immersion Circulator from reservoir before

draining.

110-874 5

WARNING: It is the user’s responsibility to properly

decontaminate the unit in the event hazardous

materials are spilled on exterior or interior surfaces.

Consult manufacturer if there is any doubt regarding

the compatibility of decontamination or cleaning

agents.

WARNING:

• Allow the bath fluid to return to ambient

temperature before draining.

• Keep within the 85°C maximum operating

temperature limit if using a polycarbonate bath.

Regulatory Compliance and Testing

The following are the compliance certifications for the equipment.

120V Units - ETL Certification

UL 61010-1 / CSA C22.2 No. 61010-1, 2nd Edition

07/12/04 (R 10/28/2008)

IEC 61010-2-010: 2003, CSA C22.2 No. 61010-2-

010:2004/07/01 Ed:2 (R2009)

IEC 61010-2-051: 2003, CSA C22.2 No. 61010-2-051:04

Ed:2 (R2009)

240V Units - CE Compliance

Low Voltage Directive 2006/95/EC

EN 61010-1, 2nd Edition Issued March, 2001

EN 61010-2-010 2nd Edition Issued October, 2003

EN 61010-2-051 2nd Edition Issued October, 2003

EMC Directive 2004/108/EC

EN 61326-1: 2006

Machinery Directive 2006/42/EC Annex I

All Units - RoHS2 2011/65/EU

6110-874

Unpacking Your Immersion Circulator

Your Immersion Circulator is packed in a special carton. You

should keep this carton, along with all packing materials, until the

unit has been installed and you are certain it is working properly.

CAUTION: Remove any loose packing material that

may have fallen into the heater/pump housing during

shipping. Before powering up, check that nothing

remains around the heater or circulator pump.

We recommend that you begin using your Immersion Circulator

immediately to confirm proper operation.

In the unlikely event that the unit was damaged or does not

operate properly, immediately contact the company where your

Immersion Circulator was purchased.

• LX Immersion Circulator

• Quick-Start Guide

• Operator’s Manual

• Selection Guide

Package Contents

This product has been tested to the requirements of CAN/

CSA-C22.2 No. 61010-1, second edition, including Amendment

1, or a later version of the same standard incorporating the same

level of testing requirements.

The user shall be made aware that the protection provided by

the equipment may be impaired if the equipment is used with

accessories not provided or recommended by the manufacturer,

or used in a manner not specified by the manufacturer.

110-874 7

Controls and Components

Backlit Display

Run Button

Stop Button

Increase Value Button

Decrease Value Button

Menu Button

Cover Plate for

Over-

Temperature

Protection Reset

Button

Minimum Liquid

Level Line

Front Flow

Port

Maximum Liquid

Level Line

8110-874

Mounting Clamp

Rear Flow Port

Power Switch

Electrical Power

Cord

Removable

Heater/Pump

Access Cover

Circulating

Heating

Actual Fluid

Temperature

Set Point

Temperature

Countdown

Timer

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PolyScience Laborausrüstung Handbücher

PolyScience

PolyScience MX-CA12E Bedienungsanleitung

PolyScience

PolyScience 4100 Series Bedienungsanleitung

PolyScience

PolyScience MX-CA11B Bedienungsanleitung

PolyScience

PolyScience WBE20A11B Bedienungsanleitung

PolyScience

PolyScience WB05A11B Bedienungsanleitung

PolyScience

PolyScience WBE10A11B Bedienungsanleitung

PolyScience

PolyScience Histology Bath Bedienungsanleitung

PolyScience

PolyScience DuraChill 58 Series Bedienungsanleitung

PolyScience

PolyScience MX07R-20 Bedienungsanleitung

PolyScience

PolyScience IP-80 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung