Precor Resolute RSL 618 Bedienungsanleitung

ENGLISH

Resolute™ Strength Selectorized Line

Glute Extension RSL 618

Assembly Guide

Assembly Requirements

It takes about 90 minutes to assemble this equipment. If this is your rst time doing this, allow more time.

CAUTION

At least two people are required to assemble the equipment. DO NOT attempt to assemble this by yourself. Precor recommends that all strength equipment be bolted to the

ooring at all anchoring points.

Installation Requirements

● Unpack the boxes and assemble the equipment close to where you plan to use it.

● Locate equipment at least 40 inches (1 meter) away from any walls, furniture, or objects on all sides.

● While tightening the fasteners, be sure to leave room for adjustments. DO NOT fully tighten fasteners until instructed to do so.

● Set up and assemble the equipment on a solid, at surface, so that it remains level and stable.

● DO NOT move the equipment without assistance.

Required Tools

● Torque wrench with torque range to at least 150 ft-lb (206 N-m) and ts the following hex bits: 6, 8, and 10 mm

● Socket wrench sets, metric and standard, plus extensions

● Open-end wrench sets, metric and standard

● Hex wrench sets, metric and standard, plus extensions

●Box cutter

●Rubber mallet

● Retaining ring pliers - large, medium, and small

● Pliers - large, medium, and small

Trademarks

Resolute is a trademark and Precor is a registered trademark of Precor, Incorporated.

All other trademarks belong to their respective owners.

Part # Name Quantity Part # Name Quantity

Handle assembly 1 Kick plate 1

Front frame 1 Elbow pad 1

Lower cross brace 1 Weight labels 1

Foot plate frame 1 Washers, 11 mm 8

Pivot frame 1 End cap 1

Pivot arm 1Washer, rubber, black 1

Add-on weight 5 lb (2.2 kg) 1Wave washer 1

Shroud, rear upper 1Washers, domed, silver 4

Shroud, front upper placard 1Flat head cap screw (FHCS) M12 x 35 mm 1

Weight stack tower frame 1Socket head cap screws (SHCS) M12 x 130 mm 2

Add-on weight handle 1Socket head cap screws (SHCS) M12 x 35 mm 8

Foot plate 1 Socket head cap screws (SHCS) M10 x 65 mm 2

Top plate assembly 1Socket head cap screws (SHCS) M10 x 40 mm 2

Weight plates 10 lb (4.5 kg) 15 Button head cap screw (BHCS) M6 x 15 mm 1

Weight stack spacer, 3-inch 1Button head cap screws (BHCS) M10 x 125 mm 2

Bumpers 4 Button head cap screws (BHCS) M10 x 30 mm 5

Guide rod with cap 1Hex head screws 5/16-inch x 1½-inch 2

Guide rods 2 Nylon lock nuts, M12 2

Shroud, front lower 1Nylon lock nuts, M10 2

Shroud, rear middle 1Washer, silver, 13.5 mm ID x 35 mm OD 1

Shroud, front middle (left and right) 2Washers, 9 mm 2

Shroud, crown 1Washers, 13 mm 8

Top tray 1Washers, 11 mm, black (for foot plate) 5

Shroud, rear lower 1

Shroud, lower pulley cover 1

Parts List

Frame Assembly

DO NOT tighten fasteners until instructed to do so.

Have your assistant hold frame parts in place during assembly.

Image Hardware Instructions

12 M12 x 130 mm SHCS

4 washers, 13 mm

2 M12 nylon lock nuts

Tools: Hex wrench, 10 mm

Socket wrench, 19 mm

2 M10 x 125 mm BHCS

2 washers, 11 mm

Connect lower cross brace to weight stack tower and kick

plate .

Align to far left hole.

Insert both guide rod fasteners from user side to align kick plate.

Hand tighten only. These will be removed temporarily in a later

step.

22 M12 x 35 mm SHCS

2 washers, domed

Tool: Hex wrench, 10 mm

Connect pivot frame to weight stack tower .

49 35

32 M12 x 35 mm SHCS

2 washers, 13 mm

Tool: Hex wrench, 10 mm

Connect front frame to lower cross brace .

42 M12 x 35 mm SHCS

2 washers, domed

Tool: Hex wrench, 10 mm

Connect handle assembly to weight stack tower .

5 2 M12 x 35 mm SHCS

2 washers, 13 mm

Tool: Hex wrench, 10 mm

Connect handle assembly to front frame .

Moving Parts

Image Hardware Instructions

11 wave washer Slide wave washer onto shaft on pivot arm .

2 1 end cap

1 M12 x 35 mm FHCS

Tool: Hex wrench, 8 mm

Slide shaft of pivot arm into pivot frame and secure.

62 M10 x 40 mm SHCS

2 washers, 11 mm

Tool: Hex wrench, 8 mm

Connect foot plate frame to lower cross brace and pivot frame .

75 M10 x 30 mm BHCS

5 washers, 11 mm, black

Tool: Hex wrench, 9 mm

Attach foot plate to frame.

8Tools: Hex wrench, 10 mm

Socket wrench, 19 mm

Torque wrench

Gently rock the frame to align. Tighten all M12 fasteners to a torque of 55

ft-lb (75 N-m).

Do not tighten the M10 screws installed in step 1 at this time. They will be

removed temporarily in a later step.

Route the Cable

Image Hardware Instructions

1Tools: Two open end wrenches, 19 mm Attach cable to pivot arm . Hold the rod end and tighten the

nut. Maximum distance is 25 mm.

2Tools: Hex wrench, 8 mm

Hex wrench, 4 mm

To route the cable around the lower pulley on the weight stack

tower, remove the cable retainer. Route the cable around the

pulley and then replace the cable retainer.

3Tools: Hex wrench, 10 mm

Open-end wrench, 19 mm

Torque wrench

To route the cable to the upper pulleys of weight stack tower,

remove the cable retainers, route the cables, and replace the

retainers. Tighten to 50 ft-lb (67 N-m) of torque.

32 hex head screws 5/16 x 1½-inch

2 washers, 9 mm

Tool: Socket wrench, ½-inch

Attach elbow pad (wide side towards user) to handle assembly .

Finish the Weight Stack Tower

Image Hardware Instructions

12 M10 x 125 mm BHCS

2 washers, 11 mm

Tool: Hex wrench, 6 mm

Remove the guide rod fasteners installed in step 1 of the Frame Assembly.

2 2 guide rods

1 weight stack spacer, 3-inch

Align the weight stack spacer over the holes on the base of the tower. Insert two

weight guide rods and lean outwards about 6 inches (15 cm), enough clearance

for the weights. Flat side of weight stack spacer should face user side.

3 2 bumpers

15 10 lb (4.5 kg) weight plates

1 top plate assembly

Slide one bumper on to each rod. Place the weight plates on the rods. Ensure the

side with three holes face the user side and single hole to the back. Place the top

plate over the weight plates. The plates and top plate should align ush on the

user side.

4Straighten the guide rods to a vertical position. Have your assistant lift the guide

rods into the upper part of the frame.

5 Tools: Hex wrench, 6 mm

Torque wrench

While the assistant is holding the rods into the upper frame, replace the two

guide rod bolts, removed in step 1, underneath the guide rods in the bottom

frame. Secure them to the kick plate. Let the guide rods drop onto the bolts and

fully tighten the bolts. Tighten M10 screws to 32 ft-lb (43 N-m) of torque.

61 M10 x 65 mm SHCS

2 washers, 11 mm

1 M10 nylon lock nut

Tools: Hex wrench, 8 mm

Socket wrench, 17 mm

1 guide rod with cap

Prepare the lower base for the add-on weight assembly. Place the retaining

screw through the bracket on the weight stack spacer.

Remove the cap from the guide rod and place the rod into bracket opening se-

cured by the screw.

7 2 bumpers

1 add-on weight

1 add-on weight handle

Place one bumper onto the third guide rod, followed by another bumper (wide

sides together), the add-on weight, and the add-on weight handle.

81 M10 x 65 mm SHCS

2 washers, 11 mm

1 M10 nylon lock nut

Tools: Hex wrench, 8 mm

Socket wrench, 17 mm

Replace the cap to the top of the rod and secure top of rod to weight stack tower

frame.

37 44

91 washer, rubber

1 washer, silver 13.5 mm ID x 35 mm OD

Place the washers into the top of the cable connector in the add-on weight han-

dle.

10 Tool: Torque wrench Attach the cable to the weight stack. Thread the bolt into the top plate assembly

until the cable meets ALL of the following requirements.

The top weight begins to separate from the second weight.

The selector pin can be easily inserted into each of the weight plates.

The add-on weight is engaged when the latch is in the down position.

At least six turns of the threads on the cable bolt extend into the add-on

weight selector stem.

The distance from the underside of the jam nut to the top of the washer should

be no more than 1.61 inch (41mm).

Tighten the locking bolt against the select stem to 50 ft-lb (81 N-m) of

torque.

Check and further adjust cable connections at arms if needed.

11 1 weight labels Remove back of labels. Align top holes on labels and top weight and place pin

into hole. Remove pin and place into a lower hole on labels. Re-align labels as

necessary and then press rmly onto weights. Rub vigorously and thoroughly to

adhere. Peel the extra label away and rub remaining labels again.

12 Lubricate the guide rods with a Teon-based lubricant, such as Tri-Flow Superior

Lubricant. Remove any excess with a clean cloth or tissue.

45 31

41 mm

Inhaltsverzeichnis

Andere Precor Ellipsentrainer Handbücher

Precor

Precor Experience Sereis Bedienungsanleitung

Precor

Precor EFX 600 Line Bedienungsanleitung

Precor

Precor EFX EFX 5.23 Bedienungsanleitung

Precor

Precor Resolute RSL 505 Bedienungsanleitung

Precor

Precor EFX524 Bedienungsanleitung

Precor

Precor Experience EFX 700 SERIES Bedienungsanleitung

Precor

Precor EFX Series Bedienungsanleitung

Precor

Precor Precision 400 Series Bedienungsanleitung

Precor

Precor Experience 700 line Series Bedienungsanleitung

Precor

Precor EFX Bedienungsanleitung

Precor

Precor Resolute RSL 619 Bedienungsanleitung

Precor

Precor HANDBOEK EFX 556i Bedienungsanleitung

Precor

Precor C534i Bedienungsanleitung

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.25 Bedienungsanleitung

Precor

Precor C546 Bedienungsanleitung

Precor

Precor Resolute RSL 606 Bedienungsanleitung

Precor

Precor Experience EFX 700 SERIES Bedienungsanleitung

Precor

Precor EFX 5.17i Bedienungsanleitung

Precor

Precor 5.17 Bedienungsanleitung

Precor

Precor Elliptical Fitness Crosstrainer EFX 536i Bedienungsanleitung

Precor

Precor Resolute RSL 714 Bedienungsanleitung

Precor

Precor EFX 245 Bedienungsanleitung

Precor

Precor Elliptical Fitness Crosstrainer Experience 700... Bedienungsanleitung

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.25 Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Weslo

Weslo Momentum 4.0 Elliptical Bedienungs- und Wartungshandbuch

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

NordicTrack

NordicTrack E 9.2 Elliptical Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung

Reebok

Reebok 1000 Zx Elliptical Bedienungsanleitung