Precor 9.41s Bedienungsanleitung

9.41S, 9.41Si Treadmill

Page 1

9.41s, 9.41si Treadmill

Warning: This service manual is for use by Precor trained service providers only.

IfyouarenotaPrecorTrainedServicer,youmustnotattempttoserviceanyPrecorProduct;

Call your dealer for service.

This document contains information required to perform the majority of troubleshooting, and

replacement procedures required to repair and maintain this product.

This document contains general product information, software diagnostic procedures (when

available), preventative maintenance procedures, inspection and adjustment procedures,

troubleshooting procedures, replacement procedures and electrical block and wiring diagrams.

To move directly to a procedure, click the appropriate procedure in the bookmark section to the

left of this page. You may “drag” the separator bar between this page and the bookmark section

to change the size of the page being viewed.

Unauthorized Reproduction and Distribution Prohibited By Law

9.41S, 9.41Si Treadmill

Page 2

Section One - Things you Should Know

About This Appendix

Section One, Things You Should Know. This section includes technical specifications and a

procedure matrix. Read this section, as well as the 9.41S or 9.41Si Treadmill Owner’s Manual,

before you perform the maintenance procedures in this manual.

Section Two, Software Features. Precor’s 9.41S and 9.41Si Treadmills are programmed with

several diagnostic and setup features. This section contains the procedures you need to access

the diagnostic features on this treadmill.

Section Three, Checking Treadmill Operation. This section provides you with a quick way of

checking treadmill operation. Check treadmill operation at the end of a maintenance procedure

and when it is necessary to ensure that the treadmill is operating properly.

Section Four, Inspection and Adjustment Procedures. Perform inspection procedures when

a trouble symptom points to a particular problem and after removing and replacing major

components. Many maintenance problems can be fixed by adjusting various treadmill

components. This section also provides you with the step-by-step procedures required to make

these adjustments.

Section Five, Troubleshooting Procedures. The diagnostic and troubleshooting procedures

contained in this section should be performed when it is necessary to isolate a problem to a

particular component.

Section Six, Replacement Procedures. When a treadmill component must be replaced, go to

this section and follow the step-by-step procedures required to remove and replace the

component.

Section Seven, Wiring and Block Diagrams. This section includes wiring and block diagrams

for the 9.41S and 9.41Si Treadmill.

General Information

For the latest exploded view, part number and part pricing information, visit the Precor dealer

website at “www.precor.com/Dealer”.

9.41S, 9.41Si Treadmill

Page 3

Technical Specifications

PHYSICAL SPECIFICATIONS

Length: 76 inches (193 cm)

Width: Handrails 31.5 inches (80 cm)

Base 28.5 inches (72 cm)

Height: 50 inches (127 cm)

Running surface: 53 inches by 18 inches (135 cm by 46 cm)

Motor: 1.7 hp. continuous duty (9.41S)

Motor 2.0 hp. continuous duty (9.41Si)

Speed: 0.5 to 10 m.p.h. (0.8 to 16 kph)

10 m.p.h. is equivalent to a 6 minute mile

Incline: 0 to 12% grade

Power: 50/60Hz 120V AC

Weight: 265 lbs (119 kg)

Shipping weight: 326 lbs (147 kg)

ELECTRONIC SPECIFICATIONS

PROGRAMS:

Manual

Interval (1 minute rest: 1 minute work)

Weight Loss

Random (9.41Si only)

Heart Rate Interactive Course

6 Preprogrammed courses (3 Walk, 3 Run)

2 Custom courses

DISPLAY READOUTS:

Distance (miles or kilometers)

Time

Speed

Calories

Incline

Heart rate

Scan

9.41S, 9.41Si Treadmill

Page 4

Procedure 2.1 - 9.41S Diagnostic Program (Units Built Before

July 21, 1997)

The M9.41S diagnostic program cycles through the following modes:

Software Version Mode. Displays the PROM version number.

LED Mode. Illuminates each of the LEDs mounted on the upper PCA.

Lift Mode. Allows you to verify that the lift calibration number increments and decrements as the

INCLINE keys are pressed.

Power Bits Mode. Allows you to verify that the power bits number increments and decrements

as the SPEED keys are pressed.

Note:

When the treadmill is in power bits mode and the SPEED ▲key is selected, the treadmill speed

will increase twice as fast as it does when the treadmill is in a normal operating mode.

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

b. Press and hold the STOP, SPEED ▼, SPEED ▲and QUICK START keys

simultaneously.

c. The electronic console displays the version number of the PROM mounted on the

upper PCA. Record the PROM version number.

d. Following the version number, a horizontal line sweeps from top to bottom and then a

vertical line sweeps from right to left.

Note:

The lines check the LEDs mounted on the upper PCA. If the lines are broken when they sweep

across the electronic console, replace the upper PCA.

e. After the LED test, the electronic console displays the potentiometer increment

number.

f. Press the INCLINE keys. Verify that the running bed inclines and declines as the

INCLINE and DECLINE keys are pressed.

g. Watch the electronic console. When the potentiometer increment number is displayed

on the electronic console, enter power bit mode by starting the running belt.

Note:

When the running belt is started, the number of power bits will be displayed. Power bits represent

9.41S, 9.41Si Treadmill

Page 5

the amount of power applied to the drive motor. Power bits is the product of selected speed and

applied load.

h. Press the SPEED ▲ and ▼keys. Verify that the power bits number increments and

decrements as the SPEED keys are pressed.

i. Press STOP to return to the Enter Your Weight banner.

j. Turn off the treadmill with the circuit breaker, then unplug the treadmill from the wall

outlet.

Diagram 2.1 - 9.41S Display

9.41S, 9.41Si Treadmill

Page 6

Procedure 2.2 - 9.41S & 9.41Si Diagnostic Program

(Units Built After July 20, 1997)

Units built after July 20, 1997 used the standard access codes. The keys on the display are

hypothetically numbered for 1 to 7 from left to right. Therefore, ENTER would be key 1, INCLINE

▼ would be key 2, etc. (see Diagram 2.1) or on a 9.41Si INCLINE ▲ would be key 1, INCLINE

▼ would be key 2, etc. (see Diagram 2.2).

Placing the 9.41S or 9.41Si Treadmill in diagnostic mode causes the software to perform the

following operations:

a. Test the LED’s mounted on the upper PCA;

b. Provide the option of calibrating the lift system;

c. Display the drive motor power bits;

d. Display and test the heart rate function;

e. Display the error code log;

f. Provide a method of checking the operation of the keys on the electronic console;

g. Test the circuit breaker trip function.

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

b. Press keys RESET,5,1,7,6,5,7,6,1, sequentially.

c. Following the version number, a horizontal line sweeps from top to bottom and then a

vertical line sweeps from right to left.

Note:

The lines check the LEDs mounted on the upper PCA. If the lines are broken when they sweep

across the electronic console, replace the upper PCA.

d. After the LED test, the electronic console displays the potentiometer increment

number.

e. Press the INCLINE keys. Verify that the running bed inclines and declines as the

INCLINE and DECLINE keys are pressed.

f. Watch the electronic console. When the potentiometer increment number is displayed

on the electronic console, enter power bit mode by starting the running belt.

9.41S, 9.41Si Treadmill

Page 7

Note:

When the running belt is started, the number of power bits will be displayed. Power bits represent

the amount of power applied to the drive motor. Power bits are product of selected speed and

applied load.

g. Press the SPEED ▲ and ▼keys. Verify that the power bits number increments and

decrements as the SPEED keys are pressed.

h. Press the STOP key to exit the power bits mode and enter the heart rate mode.

i. If the heart rate option has been installed, you may test the heart rate function using a

chest strap transmitter or test transmitter.

j. Press the ENTER key to enter the error code log. The error code log will display the

last 10 errors that occurred. Error 1 will be the most recent error and error 10 will be the

oldest error. If more than 10 errors occur, the most recent error will be inserted in position 1

and all other errors will be pushed down one position. The error that was in the 10th position

will be lost. If you wish to clear the error code log, press the QUICK START and STOP keys,

simultaneously.

k. Press the ENTER key to exit the error code log and enter the key pad test.

l. Press each key one at a time the display will confirm the key that was pressed. Press

the INCLINE▼and SPEED ▲ keys, simultaneously to exit the keypad test.

m. The next test is the circuit breaker test. Follow the instructions on the display to cause

either a test trip of the treadmill circuit breaker or exit the diagnostics program.

Diagram 2.2 - 9.41Si Display

9.41S, 9.41Si Treadmill

Page 8

Procedure 2.3 - Displaying the Odometer (Units Built Before

July 21, 1997)

This procedure allows you to display the number of miles logged on the treadmill.

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

b. With the Enter Your Weight banner scrolling, press the STOP key, the SPEED ▼key,

and then the SPEED ▲key sequentially.

c. The console displays the number of miles logged on the treadmill.

d. Turn off the treadmill with the circuit breaker, then unplug the treadmill from the wall

outlet.

9.41S, 9.41Si Treadmill

Page 9

Procedure 2.4 - Displaying the Odometer (Units Built After

July 20, 1997)

The diagnostic program used prior to July 21, 1997 and the diagnostic program used after July

20, 1997 are essentially the same except that the key strokes used to access the programs are

different. Units built after July 20, 1997 used the standard access codes. The keys on the display

are hypothetically numbered for 1 to 7 from left to right. Therefore, ENTER would be key 1,

INCLINE ▼ would be key 2, etc. (see Diagram 2.1) or on a 9.41Si INCLINE ▲ would be key 1,

INCLINE ▼ would be key 2, etc. (see Diagram 2.2).

This procedure allows you to display the number of miles logged on the treadmill.

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker

b. Press keys RESET,6,5, sequentially.

c. The software version will be displayed. Press the ENTER key to continue.

d. The console displays the number of miles logged on the treadmill.

e. Turn off the treadmill with the circuit breaker, then unplug the treadmill from the wall

outlet.

9.41S, 9.41Si Treadmill

Page 10

Procedure 2.5 - Selecting U. S. Standard or Metric Units (Units

Built Before July 21, 1997)

Selecting United States standard units causes information to be displayed in feet, miles and

pounds. Information is displayed in meters, kilometers and kilograms if metric units are selected.

After you have selected a measurement standard, the software compiles and records workout

information in the units of the measurement standard selected. Changing to the alternate

measurement standard after your workout has started will cause invalid data to be displayed. For

this reason, change the measurement standard only after turning ON the treadmill.

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

b. With the Enter Your Weight banner scrolling, press and hold the SPEED ▲and QUICK

START keys simultaneously until the Press ▲for MPH or ▼for KPH message scrolls

across the screen.

c. Use the SPEED ▲or SPEED ▼key to select the measurement standard.

Note:

When the treadmill is turned off or unplugged it will remember the last measurement standard

selected.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Precor Tretmühle Handbücher

Precor

Precor M9.25i Bedienungsanleitung

Precor

Precor Experience 700 line Series Bedienungsanleitung

Precor

Precor M 9.2s Bedienungsanleitung

Precor

Precor 904 Bedienungsanleitung

Precor

Precor 9.35 Bedienungsanleitung

Precor

Precor Experience Series 700 Line Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

Precor

Precor 9.33 Betriebsanleitung

Precor

Precor ENERGY SERIES Bedienungsanleitung

Precor

Precor Cycles Integrated LCD Screen Option none Bedienungsanleitung

Precor

Precor Experience Series 700 Line Bedienungsanleitung

Precor

Precor 9.31 Bedienungsanleitung

Precor

Precor M9.21i Bedienungsanleitung

Precor

Precor C932i Bedienungsanleitung

Precor

Precor 9.23 Bedienungsanleitung

Precor

Precor TRM 425 Bedienungsanleitung

Precor

Precor TRM 211 Technisches Handbuch

Precor

Precor 9.31 Bedienungsanleitung

Precor

Precor GEN06 Series Bedienungsanleitung

Precor

Precor GEN06 Series C952 Bedienungsanleitung

Precor

Precor C966 Gebrauchsanweisung

Precor

Precor C952i Bedienungsanleitung

Precor

Precor M9.45i Bedienungsanleitung

Precor

Precor 9.31 Betriebsanleitung

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack NTL12941 Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung