Prem-I-Air EH1550 Bedienungsanleitung

EH1550/EH1552/EH1554/EH1556

500 W / 1 kW / 1.5 kW / 2kW

Programmable Panel Heater

Chauffage Radiant Programmable

IMPORTANT

Installer and Users please note:

These instructions should be read carefully and left with the user of the product

for future reference.

BEFORE USE

You must inspect the appliance including its cable and plug for any signs of

damage. If the product is damaged, DO NOT use it, and contact your supplier

immediately.

INSTALLATION

For free-standing use: Attach the two castor-wheel brackets to the underneath

of the heater using the eight M4x8 mm screws (four in each bracket). The longer

side of the bracket goes at the back of the heater. Attach two castor-wheels to

each bracket using the dome-nuts provided.

To wall-mount: Depress the two clips and remove the wall-mounting bracket

from the heater. Using the bracket as a template, and using a spirit level to

makes sure that the bracket is fitted level, drill four holes in the wall, the lower

holes should be be at least 160 mm above the floor. Insert a wall-plug into each

hole. Fix the bracket to the wall with the four screws supplied. Align the two

raised areas on the back of the heater with the lower part of the bracket, then

clip the heater into the bracket at the top (see photo).

If correctly installed the heater will be firmly fixed at both top and bottom.

PAT TESTING

When used in a workplace, this product must be safety-tested yearly by a

qualified electrician (PAT Tested) in order to comply with the Electricity at Work

Regulations.

We recommend that it is PAT tested regularly when used in a domestic

environment.

PRODUCT SAFETY

•This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved.

•Children shall not play with the appliance.

•Cleaning and user maintenance shall not be made by children without

supervision.

•Place the heater on a firm flat surface. Ensure that the air inlets (at the

bottom) and the air outlets (at the top) are not obstructed.

•Ensure that curtains are at least 900mm (3') from the top of the heater

•Leave a gap of at least 50mm (2") at the sides of the heater.

•If used free-standing, do not operate unless the feet are correctly attached.

•Do not place on soft surfaces.

•Do not cover. This symbol shown on the casing of the heater means

that the heater should not be covered in order to avoid overheating.

•For indoor use only.

•Do not use in the immediate surroundings of a bath, a shower or a swimming

pool. (refer to Section 701 of the 17

Edition of the IEE Wiring Regulations)

•Do not place the mains lead beneath a carpet or rug.

•Do not use the heater in locations where paint, petrol or other flammable

liquids are used or stored.

•Do not locate the appliance immediately below a socket outlet

GENERAL SAFETY REQUIREMENTS

Domestic wiring must be tested periodically by a qualified electrician at least

once every 10 years or at every change of occupancy.

For office and retail premises, and buildings such as village halls, the wiring must

be inspected at least once every 5 years.

It is recommended that all buildings be fitted with smoke alarms (it is mandatory

for new buildings)

OPERATING COSTS

At time of going to press, the average cost of electricity is £0.13 per unit (kilowatt-

hour). The amount you are being charged will be shown on your electricity bill.

At this cost, the running costs will be as follows:

EH1550 £0.07 per hour

EH1552 £0.13 per hour

EH1554 £0.21 per hour

EH1556 £0.26 per hour

These figures apply with the temperature programmed to its highest setting.

The running costs will be lower if programmed to a lower temperature, or if the

ambient temperature is higher.

OPERATION

Plug the mains lead into a 13 Amp mains socket.

If connecting via an extension lead, make sure that the lead is rated at 13 Amps,

and that it is fully unwound.

Switch the unit on at the mains socket, and at the switch on the side of the

heater. The display will flash briefly, then will show the current room temperature,

and the operating mode. There are six operating modes:

, -1, -2, , 

and

The modes are as follows:



= comfort mode.

-1

= 1°C below comfort mode temperature

-2

= 2°C below comfort mode temperature

= economy mode (3½°C below comfort mode temperature)



= frost protection mode (keeps the temperature above 7°C)

= program mode – the heater is controlled by a 7-day programmable timer,

which can be programmed as detailed below.

To change mode press MODE repeatedly until the symbol for the required mode

is displayed.

To set the operating temperature, press MODE repeatedly until



is displayed,

then press the + and – repeatedly until the required temperature for comfort

modes is displayed. (The °C symbol on the display flashes whilst the operating

temperature is being set, and appears constant when room temperature is being

displayed)

Do not touch the case when the heater is in operation, because it will be hot.

Unplug the heater from the mains when not in use.

PROGRAMMING THE TIMER

Press MODE repeatedly until

is displayed.

At the top left of the display, the numerals 1 to 7 are displayed, these correspond

to the the days of the week (Sunday to Saturday). In the lower half of the display,

twenty-four symbols are displayed. These represent the operating mode of the

heater for each hour of the day.

represents Comfort mode

represents 1°C below comfort mode

represents 2°C below comfort mode

represents Economy mode (3½°C below comfort mode)

represents Frost protection mode.

Press the + or – keys until the symbol is above the correct day of the week.

Press

again, and the clock will be displayed, with the hours digits flashing. If

the clock is not correct adjust the hours using the + and – buttons.

Press

again, and the clock will be displayed, with the minutes digits flashing. If

the clock is not correct adjust the hours using the + and – buttons.

Press

again and the symbol will flash above the figure “1” indicating that the

settings for the first day of the week are being programmed.

The first segment of the 24-segment display will be flashing, indicating the setting

for the first hour (between midnight and 1 am) is being programmed.

Press the MODE button repeatedly until the required mode for this time period is

shown, then press the + button to go on to the next hour period.

Repeat until all 24 hour periods have been programmed.

At any time it is possible to press the “–“ button to return to the previous hour

period.

Then press

to save the settings for the first day, and move on to the second

day of the week. The symbol will flash above the figure “2”.

Repeat until all seven days have been programmed.

When all seven days have been programmed, press

again and the heater will

run the program that has been entered (

shown in the display).

The progamming function can be locked to prevent tampering by pressing both

the + and – keys together and holding down for 3 seconds.

The function can be unlocked to allow programming by pressing both the + and –

keys together again and holding down for 3 seconds.

The display shows [ _ _ ] to indicate that the panel is locked.

Do not touch the case when the heater is in operation, because it will be hot.

Unplug the heater from the mains when not in use.

MAINTENANCE

Before cleaning, turn the heater off, and disconnect from the mains supply. The

heater may then be cleaned using a damp cloth with a drop of washing-up liquid

to remove any dust or dirt from the case. Do no use stronger detergents or

solvents as these may damage the plastic.

If the mains lead is damaged, it must be replaced by the manufacturer or and

authorised service centre.

If the mains plug needs to be replaced, proceed as follows:

•Connect the brown wire to the terminal

labelled "L".

•Connect the blue wire to the terminal

labelled "N".

•Connect the green/yellow wire to the

terminal labelled with the earth symbol or

"E".

•Make sure that the cord-grip is positioned

correctly (over the outer sheath of the

cable) and it fully tightened.

FAULT-FINDING

The heater has an overheat protection switch, which disconnects the power if the

element gets too hot. The usual reason for this is because the air-flow has been

obstructed. If the heater ceases to operate, leave it for 20 minutes to cool down,

then check that the grilles are not being obstructed.

Switch back on, and check that the unit is operating normally. If not, contact an

authorised service agent for repair.

If the keypad is unresponsive, and the display shows [ _ _ ] then the panel has

been locked. Press + and – together and hold for 3 seconds to unlock it.

DISPOSAL AND RECYCLING

You must not dispose of this appliance with domestic household waste.

Most local authorities have specific collection system for appliances and

disposal is free of charge to the end-user.

When replacing an existing appliance with a similar new appliance your

retailer may take the old appliance for disposal.

TECHNICAL SPECIFICATION

Dimensions (wall mounting): EH1550 440x402x119 mm

EH1552 543x402x119 mm

EH1554 683x402x119 mm

EH1556 983x402x119 mm

Dimensions (floor standing): EH1550 440x450x238 mm

EH1552 543x450x238 mm

EH1554 683x450x238 mm

EH1556 983x450x238 mm

Weight: EH1550 3.2 kg

EH1552 4.01 kg

EH1554 4.85 kg

EH1556 6.5 kg

Power supply: 230 V AC

Power consumption: EH1550 500 W

EH1552 1 kW

EH1554 1.5 kW

EH1556 2 kW

Operating current: EH1550 2.2 A

EH1552 4.3 A

EH1554 6.5 A

EH1556 8.7 A

SERVICE WARRANTY

•Prem-i-Air guarantees the product free from defects in materials and

workmanship for a period of twelve months.

•Should this appliance be operated under conditions other than those

recommended, at voltages other than the voltage indicated on the appliance,

or any attempts made to service or modify the appliance, then the warranty

will be rendered void.

•The product you buy may sometimes differ slightly from illustrations. This

warranty is in addition to, and does not affect, your statutory rights.

•Our guarantee is administered by our retailers.

•If your product arrives damaged, you must contact the retailer from whom

you bought it. The retailer's contact details will be on the invoice that arrived

with the product, or on the e-mail you received when you placed the order.

Do not contact Prem-i-air, only your retailer can arrange a replacement.

•If your product fails within the guarantee period, firstly read the "fault finding"

section of this manual, because temperature and weather conditions can

affect the performance of certain products. If the product needs to be

repaired or replaced, you must contact the retailer from whom you bought it.

•The retailer's contact details will be on the invoice that arrived with the

product, or on the e-mail you received when you placed the order.

•If you have just received your product and require techical help in using it,

please call our Help Desk on (0845) 459 4816

•If you have any other technical queires about the product, please call our

Help Desk on (0845) 459 4816

Prem-i-Air Appliances Ltd.,

Lancots Lane, Sutton,

St. Helens, Merseyside.

WA9 3EX

website: www.prem-i-air.com

IMPORTANT

Installateurs et Utilisateurs, veuillez noter:

Vous devez lire cette notice attentivement et la conserver précieusement pour

une éventuelle future consultation.

AVANT UTILISATION

Vous devez contrôler l'appareil y compris le câble et la prise. Si le produit est

endommagé, NE l'utilisez PAS et contactez immédiatement votre revendeur.

INSTALLATION

Pour une utilisation en mode auto-portant :

Fixez les 2 supports de fixation à roulettes pivotantes sur la face arrière du

radiateur à l'aide des 8 vis M4 (quatre dans chaque support).

Le côté le plus long du support se place sur l'arrière du radiateur. Fixez les deux

roulettes sur chaque support à l'aide des écrous à dôme fournis.

Pour une installation murale :

Appuyez sur les deux clips et et ôtez l'étrier de fixation murale du radiateur. En

utilisant l'étrier comme un gabarit et un niveau à bulles, percez quatre trous dans

le mur.

Les trous les plus bas doivent être percés à au moins 160mm du sol. Insérez

une cheville murale dans chaque trou. Fixez le support au mur avec les quatre

vis fournies.

Alignez les deux zones en relief situées sur l'arrière du radiateur avec la partie

inférieure de l'étrier de fixation puis clipsez le radiateur sur le haut du support

(voir photo).

S'il est correctement installé, le chauffage sera solidement fixé aussi bien en haut

qu'en bas.

CONSIGNES DE SECURITE

•Cet appareil peut être utilisé par des enfants âgés de 8 ans et plus et par des

personnes dont les capacités physiques, sensorielles ou mentales sont

diminuées ou manquant d'expérience ou de connaissances uniquement sous la

surveillance d'un adulte qui leur aura appris à utiliser l'appareil et leur aura

expliqué les risques encourus.

•Les enfants ne doivent pas jouer avec l'appareil.

•Placez le radiateur sur une surface plate. Vérifiez que les entrés d'air (en-

dessous) et les sorties d'air (au-dessus) ne sont pas obstruées;

•Respectez un espace minimum de 900 mm entre le haut du radiateur et les

rideaux.

•Laissez un espace libre de 50 mm minium de chaque côté du radiateur.

•Si vous l'utilisez en mode autonome, ne l'utilisez jamais sans avoir au préalable

correctement fixé les pieds en plastique.

•Ne le placez pas sur une surface molle ou instable.

Ne pas couvrir. Ce symbole situé sur le radiateur signifie que celui-ci

ne doit pas être couvert afin d'éviter une surchauffe.

•

•Pour utilisation à l'intérieur uniquement.

•Ne pas utiliser dans les alentours immédiats d'une salle de bains, d'une cabine

de douche ou d'une piscine.

•Ne placez pas le cordon d'alimentation sous un tapis ou une carpette.

•N'utilisez pas le radiateur dans des endroits où sont stockés ou utilisés de la

peinture, de l'essence ou d'autres liquides inflammables.

•N'insérez pas d'objets dans le grilles du radiateur. Cela pourrait endommager

l'appareil et provoquer une surchauffe ou un choc électrique.

•Ne placez pas le radiateur directement sous une prise de courant.

TEST DE CONFORMITE

Si vous utilisez cet appareil sur un lieu de travail, il doit être contrôlé tous les ans

par un électricien qualifié qui vérifiera la conformité aux normes électriques en

vigueur.

Nous vous conseillons de le faire contrôler régulièrement quand vous l'utilisez à

la maison.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Prem-I-Air Heizung Handbücher

Prem-I-Air

Prem-I-Air N10T24 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EHO154 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1688 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1434 Bedienungsanleitung

Prem-I-Air

Prem-I-Air N10Turbo Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH0153 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH0291 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1372 Bedienungsanleitung

Prem-I-Air

Prem-I-Air PFH550 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1712 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1436 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1426 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1844 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH0286 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1442 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1526 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1710 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1710 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1530 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1266 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1644 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1404 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH1794 Bedienungsanleitung

Prem-I-Air

Prem-I-Air EH0154 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung