Prestige 5WTX Betriebsanleitung

128-7408A

1 of 8

BUTTON RECEIVER

CHANNEL SYSTEM FUNCTION

Lock And Arm Alarm, also initiate and

terminates *Panic

Unlock And Disarm, also initiates and

terminates *Panic. Programmable to

unlock drivers door and or all doors.

Lock and arm/unlock and disarm. May

be programmed to unlock driver's door

or all doors. Also will initiate and

terminate *Panic.

Pulsed or switched output to control

Remote Trunk Release or optional

device connected to channel 3.

When pressed and release two times,

will provide pulsed output or activate the

Remote Start option when installed.

When so equipped, this button can be

used to operate an optional device

connected to channel 4.

When so equipped, this button can be

used to operate an optional device

connected to channel 5.

These transmitters makes use of icons (symbols) to identify the reac-

tion your security system/keyless entry/and or remote start system,

where applicable, will have when any icon (button) is pressed.

These icons are programmed at time of installation to meet the needs of

the individual and to complement the vehicle that the system is installed

in. To replace a transmitter or add transmitters, please follow the

programming instructions listed on the pages of this manual.

Transmitter Programming Guide

* Where So Equipped

Model 5WTX

Rev "a" To indicate PBLED 7/06

128-7408A

2 of 8

Some of the more popular options available for the unused Option

Buttons of your transmitter are:

Remote Garage Door Interface, Remote car starter, Remote window

roll up, Remote trunk release relay.

Although the most common use of the transmitter buttons are shown

on the front page of this guide, any button or button combination can be

programmed into any receiver channel. Additionally, if all 4 buttons are

used and you require access to a 5th channel, you would program a

combination of buttons to control the 5th function; i.e... you have

programmed lock for arm, unlock for disarm, trunk for trunk release,

and OPT1 for garage door operation, and you've added a window up

module that you want independent control of, you would program un-

lock and trunk buttons pressed simultaneously into the receiver to con-

trol this function independently. Also, if you do not program a transmit-

ter button into channel 2 which is the separate unlock/disarm chan-

nel, then whatever button is programmed into channel 1 will serve

as both lock/arm & unlock/disarm.

PROGRAMMING TRANSMITTERS:

Note: It is important to remember that during the programming mode,

each individual step must be completed within 15 seconds of

the previous step. If the 15 second time limit expires between

steps, the unit will automatically exit the program mode. This

is indicated by a long chirp from the siren.

Non alarm models will flash the parking lights only to confirm the

transmitter code has been learned and stored.

Note: Because the system may be capable of sounding a siren, the

vehicle horn, or both, where the siren chirp is referenced be-

low, the siren may chirp, the horn may beep, or both devices

may sound.

This transmitter is also capable of one button programming for certain

model Audiovox Alarms. If your alarm is one of these models, then

when step 4 is completed on the following page, you can turn the

ignition switch off and programming with the default button configura-

tions for the first four channels will be complete.

TO PROGRAM ADDITIONAL TRANSMITTERS:

Note: Some systems may use a combination pushbutton LED switch.

In these systems the pushbutton and the dash mounted LED are one

and the same.

1) Enter the vehicle, and turn the ignition switch to the on position.

2) Press and release the valet push button switch three times.

Note: Some units may be packaged with a Push-Button LED combina-

tion switch.

3) The dash mounted LED will flash 1x, and the siren will chirp 1x,

indicating that the system is ready to accept programming of channel

#1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.

4) Press and hold the lock or lock/unlock symbol button of the transmit-

128-7408A

3 of 8

ter you wish to program for 4 seconds or until a long chirp is heard

from the siren.

"Repeat step 4 for each transmitter you wish to program".

Note: If your transmitter button has the Lock/Unlock icon on one

button, press and release the valet push button switch 2 times

then move on to step #8.

5) Press and release the valet push button switch one time to advance

to channel 2. The siren will chirp 2 times and the dash mounted LED

will Flash 2 times, indicating that the unit is ready to accept program-

ming for channel # 2 which is only used for separate lock and

unlock button transmitters, and is the disarm/unlock/unlock 2 and

panic.

6) Press and hold the unlock symbol button of the transmitter you wish

to program for 4 seconds or until a long chirp is heard from the

siren.

"Repeat step 6 for each transmitter you wish to program".

7) Press and release the valet pushbutton switch one time to ad-

vance to channel 3. The siren will chirp 3 times and the dash

mounted LED will Flash 3 times, indicating that the unit is ready

to accept programming for channel # 3 which is the trunk re-

lease/alternate output channel of the system.

8) Press and hold the trunk/key symbol button of the transmitter you

wish to program for 4 seconds or until a long chirp is heard from the

siren.

"Repeat step 8 for each transmitter you wish to program".

9) Press and release the valet pushbutton switch one time to advance

to channel 4 if so equipped. The siren will chirp 4 times and the

dash mounted LED will flash 4 times, indicating that the unit is ready

to accept programming for channel # 4, optional device (where

equipped)

10)Press and hold the Option button of the transmitter you wish to

program for 4 seconds or until a long chirp is heard from the siren.

"Repeat step 10 for each transmitter you wish to program".

11) Press and release the valet pushbutton switch one time to advance

to channel 5 if so equipped. The siren will chirp 5 times and the

dash mounted LED will Flash 5 times, indicating that the unit is

readytoacceptprogrammingforchannel #5 optional device(where

equipped)

12) Press and hold the second Option button of the transmitter you

wish to program for 4 seconds or until a long chirp is heard from the

siren.

"Repeat step 12 for each transmitter you wish to program".

ERASINGTRANSMITTERS IF THEYHAVEBEENLOST OR STOLEN:

Note: Before you begin to erase the lost or stolen transmitter(s),

have all transmitters available that you wish to remain pro-

128-7408A

4 of 8

grammed. These will be used during the program process

to identify transmitters that will continue to be used.

Enter the transmitter program mode:

1. Turn the ignition switch to the “ON” position.

2. Within 10 seconds, press and release the valet/program switch

three times. (Siren emits 1 short chirp indicating channel 1 has

been entered)

3. Within 10 Seconds, press and hold the ARM or ARM/DISARM

button of the first transmitter you wish to remain stored into the

control unit until a single chirp is heard from the siren.

(Repeat this for each transmitter you wish to remain stored in the control

unit).

The receiver stores up to four transmitters. To be certain all transmitter

slots in the receiver are occupied with transmitters you wish to con-

tinue to use, and all others are erased, you will have to fill all four

receiver slots. If in step 3 you identified one transmitter, you will have

to fill the additional 3 slots. If in step 3 you identified two transmitters,

you will have to fill the additional two slots, etc...

4. Press and hold any unused button or combination of buttons until a

long chirp is heard from the siren. Release and press the button or

button combination again and again until all remaining slots are full.

Note: The button or combination of buttons entered will also control

the arm or arm/disarm function until additional transmitters are

added. All unwanted transmitters are now deleted.

REPRIORITIZING A TRANSMITTER’S PROGRAMMING:

To reprogram a receiver channel with a different transmitter button

once a code has been stored, there will be two options:

1. Enter the transmitter program mode of the receiver channel to be

reprogrammed. Using any unused button or combination of but-

tons, push out the stored code by pressing the unused button until

a long chirp is heard, then repeat 3 additional times. After this, you

can add any desired unused transmitter button. This action erases

only the button stored of the transmitter you are programming. All

other codes will remain stored.

2. Enter the transmitter program mode. Using any transmitter button

press and hold until a long chirp is heard. If a single chirp or multiple

chirps, (up to 7 chirps), are heard, the unit is indicating that the

transmitter has already been programmed elsewhere in the re-

ceiver. Release the transmitter button and within 5 seconds press

and hold until a long chirp is heard. This action forces the unit to

erase all stored codes of that transmitter.

The unit then exits the program mode the siren emits the program mode

exit chirp pattern. All transmitter buttons for that transmitter must now

be reprogrammed. Any other transmitter stored in the unit’s memory still

remain operational. If the button is released and not pressed again

within the 5 second period, no change in programming has been made

to the receiver channel. The programmer can move onto a different

128-7408A

5 of 8

channel or erase the transmitter codes as described in 1 above.

OPERATINGTHE FLASHLIGHT

Pressing the button with the icon shown at the right will

cause the light on the end of the unit to turn on.

The light will turn off when the button is released.

Caution! Always point the light away from you and the

eyes of others. This is a bright high intensity LED which

should not be directed toward or into the eyes of

anyone.

BATTERY REPLACEMENT:

The transmitter incorporates a small LED visible through the case

which is used to indicate battery condition. You will notice a

decrease in transmitter range as the battery condition deterio-

rates. Transmitter battery replacement is recommended at least

every 10 to 12 months, depending upon how frequently the

transmitter is used.

To replace the battery:

1) Remove the small # 0 Phillips head screw from the rear of the

case.

2) Remove the rear cover to access the discharged batteries.

NOTE: Be Careful not to lose the key ring swivel post.

3) Carefully remove the circuit board from the case.

4) Remove and properly dispose of the discharged batteries.

5) Insert the new batteries by sliding them under the battery clip

being certain to keep the + side of both batteries facing up and

away from the circuit board. Slide the new batteries back until

they are fully seated under the clip.

6) Check to be certain that the rubber button Pad is in place in the top

half of the transmitter cover, then reinsert the circuit board with

the new batteries into the case.

7) Carefully place the back cover removed in step 2 over the top

case and snap closed.

8) Reinstall the small case screw removed in step 1.

128-7408A

6 of 8

1) Transmitter Model Num-

ber_____________________

2) Name: _______________________________________

3) Address: ______________________________________

4) City: ________________ State: _____ Zip Code: ________

5) Telephone Number: (_____) _______________

6) Total Number Of Transmitters Required:

Cost Per Transmitter is: $65.00

Multiply By Number Of Transmitters X ______

7) Enter Total Amount Enclosed _________________

(New York State Residents must include the appropriate sales tax)

8) Method of Payment:

MastercardVisa Check or Money Order (do not send cash)

Make Checks Payable To Audiovox Corporation

Credit Card Number:

_________________________________

Credit Card Expiration Date: ____ / _____ / _____

9) Mail this form along with your payment to:

Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y., 11788

Attn.:TRANSMITTERDEPARTMENT

Credit card purchasers can order additional or replacement

transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and

follow the instructions from the operator interface.

Attention: Transmitter Ordering Department

Important: To help us expedite your order, please print all of the

information legibly and mail this form and your payment

according to the instructions below.

Note: Transmitter model number found on back of case.

ORDER FORM FOR 5WTX

128-7408A

7 of 8

THISPAGELEFTBLANKINTENTIONALLY

128-7408A

8 of 8

128-7408A

Inhaltsverzeichnis

Andere Prestige Autoalarmanlage Handbücher

Prestige

Prestige APS-20B Bedienungsanleitung

Prestige

Prestige 1286462 Bedienungsanleitung

Prestige

Prestige APS-25HJ Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-8122 Bedienungsanleitung

Prestige

Prestige APS-43HJ Bedienungsanleitung

Prestige

Prestige APS 33 Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-7401A Bedienungsanleitung

Prestige

Prestige APS-596E Bedienungsanleitung

Prestige

Prestige 1286469 Bedienungsanleitung

Prestige

Prestige Prestige 128-4864 Bedienungsanleitung

Prestige

Prestige APS-140 Bedienungsanleitung

Prestige

Prestige Prestige 128-7853 Bedienungsanleitung

Prestige

Prestige Prestige Platinum APS-510C Bedienungsanleitung

Prestige

Prestige Platinum APS 500 Bedienungsanleitung

Prestige

Prestige APS-997E Bedienungsanleitung

Prestige

Prestige 1286458 Bedienungsanleitung

Prestige

Prestige APS-OE2B Betriebsanleitung

Prestige

Prestige APS25Z Bedienungsanleitung

Prestige

Prestige APS510Z Bedienungsanleitung

Prestige

Prestige 1286795 Bedienungsanleitung

Prestige

Prestige APS 800a Bedienungsanleitung

Prestige

Prestige Platinum APS 996 Bedienungsanleitung

Prestige

Prestige APS-520 Bedienungsanleitung

Prestige

Prestige 1287181 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung