Prestige Prestige Platinum APS-510C Bedienungsanleitung

128-8805b

1 of 16

Page 1

PATENTED: www.voxxintl.com/company/patents

Reva: AddnewURL11/4/2011

RevbNewFormat5/2013

Model APS-510C

5 Button Remote Security System

with Dual Stage Shock Sensor

Owners Guide

Table Of Contents:

Features and Options Page 2

Your Code Hopping Transmitters Page 3

Arming Your System-Active Page 3 - 4

Protection While the System is Armed Page 4 - 5

Disarming the System Page 5 - 6

While the System Is Sounding Page 6

Intrusion Warning Signals Page 6 - 7

Valet Override, Programming Switch (PBLED) Page 7

Manually Overriding Your System Page 7 - 8

Programming Your Custom Code Override Page 8 - 9

Custom Code Programming Example Page 9

Eliminating the Normal Arm & Disarm Chirps Page 10

Remote Panic Operation Page 10 - 11

Optional Device Channels Page 11 - 12

Ignition Controlled Lock/Unlock Setting Page 12

Telematic Upgrade Page 12

Programming New Replacement or Additional Transmitters Page 12 - 13

Features And Function Settings Page 14

System FeaturesAt AGlance Page 14

Notes Page 15-16

128-8805b

2 of 16

Page 2

IMPORTANT! In order to provide the highest possible level of security to your vehicle, this

system is equipped with selectable manual override circuitry. It is possible that you will need

to manually override your security system if the transmitter becomes lost, or inoperative due

to battery failure.

Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" isnecessary to fully

understand the procedure required to enable your vehicle in such situations.

In addition, the chart on the last page of this manual has a section for the particular features

and options installed in your vehicle as well as the override method selected.

Valet Switch manual override is pre-selected from the factory,however, the system

can be configured for "Custom Code" operation. Confirm the override mode selected on the

last page of this manual, and familiarize yourself with the selection on it's operation.

FEATURES :

2 Five Button Programmable RF Transmitters

(capable of accepting 4 transmitters)

Five Channel Receiver

Code Hopping Technology

Selectable Manual Override Mode

Remote Panic in all modes

Protected Valet

User Programmable Manual Override Code

7 Function LED (Light Emitting Diode) - Arm / Disarm / Zone 1, 2, 3 / Valet / Arming

Intrusion Alert with Memory

Audible Arm / Disarm / Defective Zone / Tamper Confirmation

Instant Siren Activation

Starter Disable

Additional Engine Immobilizer Output (optional relay required)

True Last Door Arming (hardwire only)

Defective Zone By-Pass

Hardwire or Voltage Sense Selectable

Active or Passive Arming Selectable

Programmable Auto Lock On / Off

Programmable Auto Unlock On / Off

Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L

Programmable Active or Passive Door Locks

User Programmable Permanent Chirp Delete

On Command RF Chirp Delete from Transmitter

6 Tone Multi Tone Siren

RF Inhibit with ignition on

Parking Light Flasher

Plug In Dual Stage Shock Sensor

OPTIONS:

Remote Trunk Release ( must have electronic trunk release )

Remote Keyless Entry ( must have power door locks )

Multiple Vehicle Capable

Remote Starter

Remote Power Window Roll Up

Remote Garage Door Interface

Two Step Unlock Configurable

Headlight Illumination During Arming, Disarming, Or Both

Interior Illumination Upon Disarm

128-8805b

3 of 16

Page 3

YOUR"CODEHOPPING"TRANSMITTERS

The transmitters included with your new security system use the most advanced

and secure form of radio frequency transmission available on any current

automotive security system.

Some of today’s sophisticated auto thieves use a device known as a code

grabber, which will receive and store the signal from your keychain transmitter,

and retransmit at a later time to disarm your system.

Your anti code hopping transmitters will change their signal every time the button

is pressed, so when a thief grabs then retransmits your signal, the alarm system

will not respond.

If your transmitter button is pressed more than fifty times while it is out of range

of the vehicle ( children playing with your keys ), the transmitter will not operate

when you return to the vehicle and will need to be realigned to the receiver.

To do this, simply press the lock button two times within a one second time

period. The system will now respond to that transmitter each time a button is

pressed.

NOTE: Your system has the option of using a siren, the vehicle horn, or both for

the sounding device. Where the siren is referenced below, the horn or

both may in fact chirp, or beep.

ARMINGTHESYSTEM-ACTIVE

1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.

2. Press and release the Lock button on the keychain transmitter.

Dash mounted LED begins to flash slowly.

Parking lLights flash one time.

Siren sounds one chirp.

If the siren/horn sounds 3 chirps, then you have left a door, trunk, or

hood lid ajar. Simply close the opened entry point to provide full protec-

tion. If the siren "chirped" three times, sometime after arming, the

exclusive delayed dome light learn circuit has been programmed and

the system detected a open entry point after the learned delay expired.

Again, closing the hood, trunk, or doors will correct the problem and

you do not need to disarm the system to make the correction. If the

siren/horn did not sound when arming, then the chirps have been turned

off and you should refer to the section titled "ELIMINATING THE ARM/

DISARM CHIRPS" in this manual.

Doors Lock - Optional

Headlight Illumination - Optional

128-8805b

4 of 16

Page 4

SILENTARMING-ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and hold the Lock button on the keychain transmitter for 2 seconds.

Dash mounted LED begins to flash slowly.

Parking Lights flash one time.

Siren will not sound.

If the siren "chirped" three times, sometime after arming, the exclusive

delayed dome light learn circuit has been programmed and the system

detected a open entry point after the learned delay expired. Closing the

hood, trunk, or doors will correct the problem and you do not need to

disarm the system to make the correction.

Doors Lock - Optional

Headlight Illumination - Optional

ARMING THE SYSTEM -PASSIVE (AUTOMATIC)

1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid and

trunk lid.

Dash mounted LED begins to flash rapidly, indicating 30 second

passive arming has begun.

2. Opening any protected entry point during the 30 second passive arming cycle

will immediately suspend automatic arming and the 30 second passive

arming cycle will restart when all doors are closed.

At the end of the passive arming cycle the;

Dash mounted LED begins to flash slowly.

Parking Lights flash one time.

Siren sounds one chirp

If the siren did not sound when arming, then the chirps have been

turned off, and you should refer to the section titled

"ELIMINATING THEARM / DISARM CHIRPS" in this manual.

Doors Lock - Optional

Door locking during passive arming is a selectable feature.

The alarm can be programmed to allow the doors to lock only when

arming using the keychain transmitter and they will not automatically

lock during passive arming.

PROTECTIONWHILETHESYSTEMISARMED

Opening any protected door, hood, or trunk lid will cause the alarm to

immediately sound. The alarm will continue to sound for 30

128-8805b

5 of 16

Page 5

seconds, then stop and continue to monitor all protected entry points.

If the thief left a door opened, the alarm will sound for six 30 second

cycles, remain armed and ignore that triggered zone.

Whenever the system is armed, the dash mounted LED indicator will

slowly flash. This serves as a visual deterrent to the potential thief.

The LED is a very low current bulb and will not cause the vehicle’s

battery to drain, even when left unattended for extended periods.

Whenever the system is triggered, the vehicle’s parking lights will

flash for the full 30 second alarm cycle, attracting visual attention to

the vehicle.

Optional - Whenever the system is armed, the vehicle’s starting circuit

will be bypassed. If the thief should choose to ignore the siren, the

vehicle can not be started.

Any mild impact to the vehicle’s glass will cause the alarm to sound a

short series of warning tones.

Any strong impact to the vehicle’s glass will cause the alarm to trigger

for the full 30 second alarm cycle.

DISARMINGTHESYSTEM

1. As you approach the vehicle, press and release the Unlock button on the

keychain transmitter.

Dash mounted LED turns off.

If passive arming was selected during the installation, then the LED

will start flashing rapidly, indicating that the system is rearming auto-

matically. Open any door to suspend the automatic arming.

Parking Lights flash two times.

If the parking lights flashed three times, then the alarm was trig-

gered inyour absence. Before turning the key on, examine the LED to

identify which zone was triggered.

Siren sounds two chirps.

If the siren sounds 4 chirps, then the alarm was triggered in your

absence. Before turning the key on, examine the LED and refer to the

INTRUSION WARNING SIGNALS section of this manual to iden-

tify which zone was triggered.

If the siren did not sound when disarming, then the chirps have

been turned off, and you should refer to the section titled

“ELIMINATING THE ARM / DISARM CHIRPS“ in this manual.

Doors Unlock - Optional

Note: If the optional 2 step door unlock circuit is installed, when the un-

lock transmitter button is activated, the drivers door only will unlock,

pressing the unlock button a second time will cause all doors to

unlock. If your transmitter has a separate lock unlock buttons, press-

ing the unlock button anytime after the first unlock command will

cause all the vehicle doors to unlock.

128-8805b

6 of 16

Page 6

Headlight Illumination - Optional

Illuminated Entry Upon Disarm

SILENTDISARMING

1.As you approach the vehicle, press and hold the Unlock button on the keychain

transmitter for 2 seconds.

Dash mounted LED turns off.

If passive arming was selected during the installation, then the LED will

start flashing rapidly, indicating that the system is rearming automatically.

Open any door to suspend the automatic arming.

Parking Lights flash two times.

If the parking lights flashed three times, then the alarm was triggered in

your absence. Before turning the key on, examine the LED to identify which

zone was triggered.

Siren will not sound.

If the siren sounds 4 chirps, then the alarm was triggered in your absence.

Before turning the key on, examine the LED and refer to the INTRUSION

WARNING SIGNALS section of this manual to identify which zone was

triggered.

Doors Unlock - Optional

NOTE: If the optional 2 step door unlock circuit is installed, when the unlock

transmitter button is activated, the drivers door only will unlock, pressing

the unlock button a second time will cause all doors to unlock. If your

transmitter has a separate lock/unlock buttons, pressing the unlock

button anytime after the first unlock command will cause all the vehicle

doors to unlock.

Headlight Illumination - Optional

Illuminated Entry Upon Disarm

WHILETHESYSTEMISSOUNDING

If during a triggered state, you wish to shut off the siren without disarming your

security system, simply press and release any transmitter button other than the

disarm button. This action will turn off the siren yet leave the vehicle fully armed

and protected. This feature is particularly useful if you are aware of children

playing near your vehicle that may accidently trigger your security system. In this

case you can cancel the siren sounding without disarming your alarm.

INTRUSIONWARNINGSIGNALS

This system will inform you if an intrusion attempt has occurred while you were

away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4

times and the parking lights will flash 3 times when disarming the system. Enter

the vehicle and observe the dash mounted LED to identify which zone was

triggered.

128-8805b

7 of 16

Page 7

If the LED is flashing one time...pause...one time...pause...etc., then an

intrusion attempt was made to the shock sensor, or an accessory

triggering device that may have been added to the system.

If the LED is flashing two times...pause...two times...pause...etc., then

an intrusion attempt was made to a hood or trunk pin switch that was

added to the system, or to a light activated entry point if the alarm was

installed using the voltage sensing feature.

If the LED is flashing three times...pause...three times...pause...etc.,

then an intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory and will

only be erased when the ignition key is turned on.

PUSH-BUTTONLED/VALET/OVERRIDE/PROGRAMMINGSWITCH:(PBLED)

The PBLED switch allows you to temporarily bypass all alarm functions, elimi-

nating the need to hand your transmitter to parking attendants or garage me-

chanics. When the system is in valet mode, all alarm functions are bypassed,

however the remote panic feature and remote door locks will remain operational.

To use the valet mode, the system must first be disarmed either by using your

keychain transmitter, or by activating your personalized manual override code.

1. Enter the vehicle, and turn the ignition key to the on position.

2. Press and hold the PBLED switch until the LED turns on solid. The system

will remain in the valet mode.

3. To return to normal operation, press and release the PBLED switch any time

the ignition is on.

NOTE: Always remember to return the vehicle to the valet off position. This will

ensure that the vehicle remains protected at all times.

MANUALLYOVERRIDINGYOURSYSTEM:

USING THEPBLEDOVERRIDE SWITCH

Your Security System can be disarmed without the use of the keychain transmit-

ter. This is necessary, since you will need the ability to operate your vehicle if the

transmitter is lost or its battery fails. If your system has been selected for Valet

Switch manual override as indicated on the last page of this manual, to bypass

the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

128-8805b

8 of 16

Page 8

3. Within 5 seconds, press and release the PBLED override switch.

The alarm system will stop sounding and enter the (bypassed) mode.

You can now start and operate the vehicle normally.

Typically this override mode is used only if the transmitter has become

inoperative.

Programming Your Custom Override Code:

Unlike override switches easily found, and defeated, this security system allows

the consumer to program a personal override code, offering a higher level of

security. To take advantage of this option, programmable feature # 10 must be

selected for the Custom Code Option. Consult your installation center for pro-

gramming details. The system comes from the factory with a pre-programmed

override code of 11. To change this default override code, do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency

override sequence. Turn the ignition switch to the on position.

2. Within 10 seconds, press and release the PBLED switch, 3 times.

3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.

(The siren or horn will beep and the lights will flash one time.)

4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and

releasing the PBLED switch from 1 up to 9 times.

5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off

then on.

6. Within 10 seconds, begin to enter your chosen units digit by pressing and

releasing the PBLED switch from 1 up to 9 times.

7. Finish by turning the ignition switch to the off position.

If the new code was accepted, the unit will report back the newly entered code, by

flashing the LED, first indicating the 10ths digit, pause and then the units digit.

The unit will report the new code three times with a one second pause between

each code, then the system will begin arming. If the LED flash pattern reports the

previously stored code, the new code was not entered correctly. Please repeat

steps 1 through 7 above considering the following.

NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not

recognize a 0 (Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for

more then 5 seconds during any of the above steps, the unit will

revert back to the last successfully stored code.

128-8805b

9 of 16

Page 9

Custom Code Programming Example:

To Change the code from the factory pre-assigned code of 11 to “52” you would do

the following:

1. Disarm the system by use of the transmitter, or by use of the emergency

override sequence.

2. Turn the ignition switch to the on position.

3. Within 10 seconds, press and release the PBLED switch, 3 times.

4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.

(The siren or horn will beep and the lights will flash one time.)

5. Within 10 seconds, begin to press and release the PBLED switch to set the

tenths digit. (As per the example, press and release 5 times to set the tenths

digit to 5)

6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off

then on.

7. Within 10 seconds, begin to press and release the PBLED switch to set the units

digit.

(As per the example, press and release 2 times to set the units digit to 2).

8. Turn the ignition switch to the off position. Immediately observe the LED flash

pattern.

You will note the LED flashing five times, pause, and then flash two times, pause. This

pattern will be repeated three times indicating the new code (52) has been accepted and

stored in memory.

NOTE: If after step 7, the LED flashes a code other than what was just entered,

this indicates that the code has not been changed. You will have to

repeat steps 1 through 7 above being certain to note the following:

Acceptable digits 10ths or units are 1 through 9. The unit will not

recognize a 0 (Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more

then 5 seconds during any of the above steps, the unit will revert back to the last

successfully stored code.

128-8805b

10 of 16

Page 10

MANUALLYOVERRIDINGYOURSYSTEM:

USINGTHECUSTOM CODEOVERRIDE

Assuming the override code programmed has not been changed, and the default

override code of 11 is in the system's memory.

1) Enter the vehicle and turn the ignition switch to the on position.

NOTE: The siren will sound.

2) Within 5 seconds, press and release the PBLED switch 1 time.

3) Within 5 seconds, turn the ignition switch off then on.

4) Within 5 seconds, press and release the PBLED switch 1 time.

5) Turn the ignition switch off then on and start the vehicle.

NOTE: If you have changed the programmed override code then substitute your

new code tenths for step 2 above, and units for step 5 above.

ELIMINATINGTHENORMAL ARM/DISARMCHIRPS

You can selectively eliminate the normal arm & disarm chirps by holding the

transmitter button slightly longer when arming or disarming.

This will prevent the siren chirps for one arm or disarm cycle.

If you find this inconvenient and wish to eliminate these chirps permanently;

1. Turn the ignition switch 'on" then 'off".

2. Within 10 seconds of turning off the ignition, press and release the

Push Button LED switch 3 times.

3. If the chirps were on before you started, the siren will emit 2 short chirps

indicating that the chirps are now off. If the chirps were off before you started,

the siren will emit one short chirp indicating that the chirps are now on.

NOTE: If the vehicle battery is disconnected then reconnected, the unit will re-

turn to the default setting of chirps on. Repeat the above procedure to

eliminate the arm/disarm chirps.

REMOTE PANICOPERATION

TheARM or DISARM button on your keychain transmitter also functions as a panic

switch for use in emergency situations. To use remote panic:

Inhaltsverzeichnis

Andere Prestige Autoalarmanlage Handbücher

Prestige

Prestige 1286459 Bedienungsanleitung

Prestige

Prestige APS510Z Bedienungsanleitung

Prestige

Prestige APS-25HJ Bedienungsanleitung

Prestige

Prestige APS-20B Bedienungsanleitung

Prestige

Prestige Prestige 128-4246A Bedienungsanleitung

Prestige

Prestige APS-20B Bedienungsanleitung

Prestige

Prestige Platinum+ APS-596 Bedienungsanleitung

Prestige

Prestige APS-122E Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-8122 Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-8128 Bedienungsanleitung

Prestige

Prestige Prestige APS-20B Bedienungsanleitung

Prestige

Prestige APS-997C Bedienungsanleitung

Prestige

Prestige APS-43HJ Bedienungsanleitung

Prestige

Prestige 5WTX Betriebsanleitung

Prestige

Prestige APS-997E Bedienungsanleitung

Prestige

Prestige Owner's Manual Bedienungsanleitung

Prestige

Prestige Prestige 128-7853 Bedienungsanleitung

Prestige

Prestige APS 800a Bedienungsanleitung

Prestige

Prestige APS-OE2B Betriebsanleitung

Prestige

Prestige 1287181 Bedienungsanleitung

Prestige

Prestige 1286458 Bedienungsanleitung

Prestige

Prestige APS-510E Bedienungsanleitung

Prestige

Prestige APS-922E Bedienungsanleitung

Prestige

Prestige 1286462 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung