Prestige APS-20B Bedienungsanleitung

Model APS-20B

Owner's Manual

3 Button Vehicle Alarm System

With Channel 3 Auxiliary Output

FEATURES:

2 Three Button RF Transmitters

Three Channel Code Learning Receiver

Remote Panic In All Modes

Built-InParkingLightOutput

LED Status Indicator

Multi-ToneSiren

True Last Door Arming

Channel3AuxiliaryOutput

OPTIONS:

Remote Trunk Release

Remote Power Window Control

Remote Garage Door Interface

Remote Engine Starter

Single or Dual Stage Shock Sensor

StarterInterrupt

Keyless Entry

Ignition Control Door-Locks

Page 1

YourAPS-20BVehicle AlarmSystemhasmany featuresandavailable optionssomeofwhich

mustbeselected at time of installation. For your reference,the list on the back page ofthis

manual shows what features and options have been installed with this particular system.

Consultyourinstallingdealer for options that may have been installed andarenotlisted.

ARMINGTHE SYSTEM- ACTIVE

1.Turnthe engine off, exit the vehicle andcloseall doors.

2.Pressandreleasethelockbuttonofyourkeychaintransmitteronetime.

The parking lights will flash once, the siren will chirp once, and the dash mounted LED will

beginto flashslowlyconfirming thesystemisarmed. Ifyouhavetheoptionaldoorlock/unlock

circuitinstalled,thedoorswill also lock.

SILENTARMING -ACTIVE

1.Turnthe engine off, exit the vehicle andcloseall doors.

2.Press and hold the lockbutton of your keychain transmitter for two seconds.

The parking lights will flash once and the dash mounted LED will begin to flash slowly

confirmingthesystem is armed. The siren will not chirp. If youhavethe optional door lock/

unlockcircuitinstalled,thedoorswilllock.

ARMINGTHE SYSTEM- PASSIVE (AUTOMATIC)

Ifthepassivearmingfeaturehas been selected:

Turntheengine off, exit the vehicle and close alldoors.

The dash mounted LED will immediately begin to flash rapidly indicating that the 30 second

passivearming timer hasbegun. IftheLEDdoes not begintoflashrapidly,then you haveleft

adoor, hood or trunk ajar. Closingthisentrypointwillallowthearmingcycletobegin. Ifany

entrypoint isopenedduringthe 30 secondarmingcycle, arming willbesuspended. When all

entrypointsareclosed,the arming cycle will begin again. At the end of the30seconds,the

parkinglights will flashonce,thesirenwill chirp onceandthedash mounted LEDwillbeginto

flashslowlyconfirming the systemisarmed. Ifthesiren did notsoundwhenarming,then the

chirps have been turned off. Please refer to the section titled "Eliminating the Arm/Disarm

Chirps" later in this manual. Passive door locking is a selectable feature. If you have the

optionaldoor lock/unlockcircuitinstalled,the doorsmayormay notlockpassivelydependent

uponthe setup duringinstallation.

PROTECTIONWHILETHESYSTEMISARMED:

Whenever the system is armed, opening any protected entry point, (i.e.; hood, trunk, or

doors),will cause thealarmtotrigger immediately. Thesirenwillsound andtheparkinglights

willflashfor 30 seconds, thenstopandresetto continue to monitorallprotectedentrypoints.

Ifthethiefhappenedtoleavetheentrypointopen,thesystemwillsoundforsixconsecutive

30secondcyclesthenshutdownandreset,isolating the triggered zone, while continuing to

monitorandprotectall other zones.

Whenever the system is armed, the dash mounted LED will slowly flash. This serves as a

visualdeterrentto a potentialthief. ThisLEDisa very lowcurrentlightemittingdiode and will

notcausethe battery to drain even ifleft unattended for long periods oftime.

Ifthe

optional

shocksensorisinstalled,anystrong impact to thevehiclewillcausethe shock

Page 2

Page 3

detectorto trigger the alarm when armed. Ifthe

optional

2-stageshock sensor is installed,

anylesser impact willcausethepre-detect stage oftheshocksensor to emitaseriesof short

warningtones from the sirenwhen armed.

Iftheoptionalstarterinterruptisinstalledthevehiclestarter circuit is disabled, even with the

ignitionkeythevehiclewillnot start.

DISARMINGTHESYSTEM

Asyouapproachthevehicle,pressand release the unlock button on the keychain transmit-

ter.

Theparking lightswillflash twotimes,the sirenwillchirp twiceandthe dashmountedLEDwill

turnoff. Ifyouhave the optional door lock/unlock circuit installed, thedoorswillunlock.

Note: Ifthepassive arming mode was selectedatthetimeofinstallation, the dash mounted

LEDwillstart flashing rapidly indicating that the systemis rearming. Opening any door will

suspendthe automaticarming.

Iftheparkinglights flashed three times and the sirenchirpsfourtimes,thisindicatesthatthe

alarmsystemhadbeen triggeredinyourabsence. Beforeturningontheignition key,examine

thedashmountedLED'sflashpattern. Thenumberofflashesidentifiesthetriggeredzone.

Foradditionalinformation,refertoINTRUSIONWARNINGSIGNALSfoundlaterinthismanual.

If the siren did not sound upon disarm, then the chirps have been turned off. Refer to the

sectiontitledELIMINATINGTHEARM/DISARMCHIRPS.

SILENTDISARMING

1. Asyouapproachthevehicle, pressand holdtheunlockbuttonofyourkeychaintransmitter

for two seconds, or until the system responds.

Theparkinglights will flash twice and thedashmountedLEDwillturn off, confirming that the

systemisdisarmed. The siren will not chirp. Ifyouhavetheoptionaldoor lock/unlock circuit

installed,thedoorswillunlock.

Note: Ifthe passivearmingmodewas selectedattime ofinstallation,thedash mountedLED

will start flashing rapidly indicating that the system is rearming. Opening any door will

suspendthe automaticarming.

Iftheparkinglights flashed three times and the sirenchirpsfourtimes,thisindicatesthatthe

alarmsystemhadbeentriggered in your absence.

VALET/PROGRAM/MANUALOVERRIDESWITCH

Thevaletswitchallows youtotemporarilypreventthealarmfromarming,eliminatingtheneed

to hand your keychain transmitter to parking attendants or garage mechanics. When the

system is in the valet mode, all alarm functions are by-passed, however the remote panic

feature,and the optional remotedoorlock/unlockwill remain operational.

Toenter the valetmode:

1. Start with the valet switch in the "off" position

2.Turntheignitionswitchtothe "on" position.

3.Within 10 seconds of step 2, flip the valet switch to the "on"position.

Thedash mountedLEDwillturn onsolidindicating thatthevaletmode hassuccessfullybeen

entered.

Page 4

Toreturnto the normal, (alarm mode), operation, move thevaletswitchto the "off"position

anytimetheignitionswitchisintheonposition.

Note:In the event thatyouloseyourkeychaintransmitterorthe transmitter fails to operate

thealarm system, thevaletswitchcanbe used todisarmthealarm. This is referredtoasthe

"ManualOverride". Todisarm thealarm:

1.Open the door with thevehicle door key. (The siren will sound)

2.Turntheignitionswitchtothe "on" position.

3.Flipthevalet/overrideswitch to the "on" position.

Thesystem willdisarmandthesirenwillstopsounding, allowingtheengine tobestarted,and

thevehicletobeoperated normally. Alwaysremember to move the valet switch back to the

"off"position to allow the passive armingand optional starter interrupt featuresto be oper-

ablethenexttimeyou park the vehicle.

INTRUSIONWARNINGSIGNAL

This systemwillinform you if an intrusion attempthasoccurred while you were away from

thevehicle. Upondisarm, the siren will chirp4timesandthe parking lights will flash3times.

Enterthevehicleand

before

turningontheignitionswitch,observetheLEDflashpattern.

IftheLEDflashes two times...pause, two times...pause etc., thenanintrusionattempt was

made to open the hood or trunk, or an impact or a strong vibration was applied that the

optionalshock sensor detected. Check thevehicle for indications of forced entry to these

openings,orsignsofglassbreakageorbodydamage.

Ifthe LEDflashesthree times...pause,threetimes...pause etc.,thenan intrusionattemptwas

madetothe vehicle doors. Check all doors forindicationsof forced entry.

Note:The LED intrusion warning indications are stored in the system's memory and will be

erasedwhen the ignition switchis turned on.

ELIMINATINGTHEARM/DISARMCHIRPS

You can selectively eliminate the normal arm or disarm chirps by holding the respective

transmitter button slightly longer when arming and disarming. This will prevent the siren

chirpsforonearmor disarm cycle. If you find this inconvenient and wish toeliminatethese

chirpspermanently,

1. Start with the valet switch in the "off" position.

2.Turn the ignition switch "on" then "off".

3. Within 10 seconds of turning off the ignition, flip the valet switch "on", "off", "on", "off",

"on", "off".

4.Ifthe chirps wereonbeforeyoustarted, the sirenwillemit2short chirps indicatingthatthe

chirpsarenow off. If the chirps were offbeforeyou started, the siren will emitoneshort

chirpindicating that the chirps are nowon.

REMOTEPANICOPERATION

Thelockandunlockbuttonsofyourkeychaintransmitteralsoservesasapanicswitch and

willcausethe siren to sound on demand. To use the panicfeature, you must be within the

system's maximum operating range. In an emergency situation, to use the panic feature,

pressand hold either thelock or unlock button of your keychain transmitter for 3 seconds.

Page 5

This will cause the lights to flash, the siren to sound. The panic mode will continue for 30

secondsandthen reset.

To disengage the panic feature before the 30 seconds are up, press and hold the lock or

unlockbuttonof your keychain transmitter for 3 seconds.

While the panic mode is engaged, the doors can be remotely locked and unlocked via the

transmitterbypressing the lockorunlockbuttonmomentarily.

ADDITIONALREMOTEFUNCTIONCHANNEL3

The system has an additional feature, (Channel 3) , that can be connected to a number of

differentoptionalaccessories. Someofthe more common uses for this channel are:

qRemoteTrunkRelease

qRemoteWindow Close

qRemoteGarage DoorInterface

To operate the accessory associated with Channel 3, press and

hold

the option button of

yourkeychaintransmitter for three seconds.

NOTE: YoumayaccesstheChannel3 commandregardlessofwhetherthe systemis"armed"

or "disarmed", but not when the ignition switch is in the on position. This is to prevent the

outputfromaccidentallyopeningthevehicle'strunk when the vehicle is in motion.

IGNITIONDOORLOCKING/UNLOCKING

When connected to a vehicle's power door lock system the unit is capable of being pro-

grammedfortheaddedsafetyandsecurityofignitioncontrolleddoorlockingandunlocking.

These features are separate, so the unit may be programmed for one, or both, or neither.

Thesefeaturescanonlybeused if the optional door lock/unlock circuit is installed.

Whenthe ignition door locking featureisprogrammed,thesystem will cause all doorlocksto

lock whenever the ignition switch is turned from the "off" to "on" position, (providing that all

doorsareclosedatthattime). Alldoorswilllockapproximately 2 seconds after the vehicle's

ignition switch is turned on. This is a nice feature for maintaining the personal safety of the

occupantsofthevehicle,inaneffortlessandautomaticmanner.

Whentheignitiondoorunlockingfeatureisprogrammed,system will cause all door locks to

unlock whenever the ignition switch is turned from the "on" to "off" position. All doors will

unlockimmediatelyafterthevehicle'signitionswitchisturnedoff.

As stated these features are programmed separately, so you may chose to use one, both,

or neither. Please consult with your dealer to consider your options.

SYSTEMFUNCTIONSATA GLANCE

ALARM LED INDICATORS:

RAPID FLASHING = PASSIVE ARMING

SLOW FLASHING = ARMED

OFF = DISARMED

ON SOLID = VALET MODE

2 FLASH...PAUSE = HOOD/TRUNK/SHOCK INTRUSION

3 FLASH...PAUSE = DOOR INTRUSION

SIREN CHIRP INDICATION:

1 CHIRP = ARM

2 CHIRPS = DISARMED

3 CHIRPS = ARMING WITH ENTRY POINT OPENED

4 CHIRPS = DISARM AFTER INTRUSION

CONTINUOUS = TRIGGERED/PANIC MODE

ALARM PARKING LAMP INDICATIONS:

1 FLASH = ARM

2 FLASHES = DISARM

3 FLASHES = DISARM AFTER INTRUSION

CONTINUOUSFLASH = PANICMODE

SELECTABLEFEATURES:

¨PASSIVEARMING

¨ACTIVEARMING

¨IGNITIONCONTROLLEDDOORLOCK

¨IGNITIONCONTROLLEDDOORUNLOCK

¨PASSIVEDOORLOCKING

¨CHIRPSON

¨CHIRPSOFF

Page 6

128-6186

Inhaltsverzeichnis

Andere Prestige Autoalarmanlage Handbücher

Prestige

Prestige Prestige Platinum APS-400 Bedienungsanleitung

Prestige

Prestige 1287181 Bedienungsanleitung

Prestige

Prestige 5WTX Betriebsanleitung

Prestige

Prestige APS-25E Bedienungsanleitung

Prestige

Prestige APS-596E Bedienungsanleitung

Prestige

Prestige APS596Z Bedienungsanleitung

Prestige

Prestige Owner's Manual Bedienungsanleitung

Prestige

Prestige APS-25E Bedienungsanleitung

Prestige

Prestige Platinum APS 500 Bedienungsanleitung

Prestige

Prestige Prestige 128-4243B Bedienungsanleitung

Prestige

Prestige APS 33 Bedienungsanleitung

Prestige

Prestige Platinum APS-787C Bedienungsanleitung

Prestige

Prestige APS-25-CL Bedienungsanleitung

Prestige

Prestige PE1BZ Bedienungsanleitung

Prestige

Prestige APS-997C Bedienungsanleitung

Prestige

Prestige Prestige Platinum APS-510C Bedienungsanleitung

Prestige

Prestige APS-997E Bedienungsanleitung

Prestige

Prestige APS-520 Bedienungsanleitung

Prestige

Prestige 1286459 Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-7401A Bedienungsanleitung

Prestige

Prestige 1286469 Bedienungsanleitung

Prestige

Prestige APS-43HJ Bedienungsanleitung

Prestige

Prestige APS-510E Bedienungsanleitung

Prestige

Prestige APS-20B Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung