Prorack K694 Bedienungsanleitung
K694
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 1 x 4 x 4
x 2 x 2 x 4 x 1
Revision No: 6F 1
Fitting Kit K694
MAX kgs (lbs)
W/P WHD
Mazda
2, 5dr Hatch 15-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2, 5dr Hatch 15-+ AU 50 kgs (110 lbs) 50 kgs (110 lbs)
2, 5dr Hatch 15-+ EU 50 kgs (110 lbs) 50 kgs (110 lbs)
3, 4dr Sedan 14-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
3, 4dr Sedan 14-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
3, 4dr Sedan 14-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
3, 4dr Sedan 14-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
6, 4dr Sedan 12-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
6, 4dr Sedan 12-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
6, 4dr Sedan 12-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
6, 4dr Sedan 14-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
Axela, 4dr Sedan 14-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Demio, 5dr Hatch 15-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2
Fitting Kit K694
X
A B C 1 2 3
2, 5dr Hatch 15-+ (NZ) -225mm 520mm - 815mm 770mm -
-8 -7/8ths" 20 1/2ths" - 32 1/16ths" 30 5/16ths" -
2, 5dr Hatch 15-+ (AU) -225mm 520mm - 815mm 770mm -
-8 -7/8ths" 20 1/2ths" - 32 1/16ths" 30 5/16ths" -
2, 5dr Hatch 15-+ (EU) -225mm 520mm - 815mm 770mm -
-8 -7/8ths" 20 1/2ths" - 32 1/16ths" 30 5/16ths" -
3, 4dr Sedan 14-+ (NZ) -255mm 435mm - 938mm 890mm -
-10 -1/16ths" 17 1/8ths" - 36 15/16ths" 35 1/16ths" -
3, 4dr Sedan 14-+ (AU) -255mm 435mm - 938mm 890mm -
-10 -1/16ths" 17 1/8ths" - 36 15/16ths" 35 1/16ths" -
3, 4dr Sedan 14-+ (EU) -255mm 435mm - 938mm 890mm -
-10 -1/16ths" 17 1/8ths" - 36 15/16ths" 35 1/16ths" -
3, 4dr Sedan 14-+ (US) -255mm 435mm - 938mm 890mm -
-10 -1/16ths" 17 1/8ths" - 36 15/16ths" 35 1/16ths" -
6, 4dr Sedan 12-+ (NZ) -235mm 415mm - 945mm 890mm -
-9 -1/4ths" 16 5/16ths" - 37 3/16ths" 35 1/16ths" -
6, 4dr Sedan 12-+ (AU) -235mm 415mm - 945mm 890mm -
-9 -1/4ths" 16 5/16ths" - 37 3/16ths" 35 1/16ths" -
6, 4dr Sedan 12-+ (EU) -235mm 415mm - 945mm 890mm -
-9 -1/4ths" 16 5/16ths" - 37 3/16ths" 35 1/16ths" -
6, 4dr Sedan 14-+ (US) -235mm 415mm - 945mm 890mm -
-9 -1/4ths" 16 5/16ths" - 37 3/16ths" 35 1/16ths" -
Axela, 4dr Sedan 14-+ (NZ) -255mm 435mm - 938mm 890mm -
-10 -1/16ths" 17 1/8ths" - 36 15/16ths" 35 1/16ths" -
Demio, 5dr Hatch 15-+ (NZ) -225mm 520mm - 815mm 770mm -
-8 -7/8ths" 20 1/2ths" - 32 1/16ths" 30 5/16ths" -
3
Fitting Kit EN
K694
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4
Fitting Kit EN
K694
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Attaches to factory-fitted mounting points
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
5
Fitting Kit EN
K694
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6
Fitting Kit EN
K694
Fitment
●Lift and pull ditch moulding back towards
you and remove from the vehicle.
●Mark a reference point for the front and
rear mounting points with a pen as shown.
●Use drill bit supplied, to drill holes in
marked positions.
7
Fitting Kit EN
K694
●Re-install rubber ditch mould back into roof
channel and click into place.
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all four positions.
●Refer to the underside of the pad for the
part number.
8
Fitting Kit EN
K694
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 295A
B = 296A
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
●Repeat for all four positions.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
9
Fitting Kit EN
K694
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all legs.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
●If crossbars are removed, please install the
rubber plugs into the ditch moulding.
10
Inhaltsverzeichnis
Andere Prorack Autozubehör Handbücher
Prorack
Prorack K478 Bedienungsanleitung
Prorack
Prorack K574 Bedienungs- und Installationshandbuch
Prorack
Prorack K073 Bedienungsanleitung
Prorack
Prorack K091 Bedienungsanleitung
Prorack
Prorack K545 Bedienungsanleitung
Prorack
Prorack K911 Bedienungsanleitung
Prorack
Prorack K1010 Bedienungsanleitung
Prorack
Prorack K592 Bedienungsanleitung
Prorack
Prorack K485 Bedienungsanleitung
Prorack
Prorack K554 Bedienungs- und Installationshandbuch
Prorack
Prorack K483 Bedienungsanleitung
Prorack
Prorack K345 Bedienungsanleitung
Prorack
Prorack K1234 Bedienungsanleitung
Prorack
Prorack K1001 Bedienungsanleitung
Prorack
Prorack K850 Bedienungsanleitung
Prorack
Prorack K062 Bedienungsanleitung
Prorack
Prorack K474 Bedienungsanleitung
Prorack
Prorack K947 Bedienungsanleitung
Prorack
Prorack K094 Bedienungsanleitung
Prorack
Prorack K716 Bedienungsanleitung
