Prorack PR3208 Bedienungsanleitung

Page 1 of 5

09-13-569-Rev2

PR3208

Gas Bottle Restraint

First Time Installation

• Please read instructions carefully before installation.

• Check the contents of kit. Contact your Prorack dealer if any parts appear to be missing or damaged.

• Clean your roof racks and cargo basket prior to ﬁtting the Gas Bottle Restraint.

Important Warning

• It is critical that all Prorack racks and accessories be properly and securely attached to your vehicle. Improper

attachment could result in an automobile accident, and could cause serious bodily injury or death to you or to others.

• You are responsible for securing the racks and accessories to your car, checking the attachments prior to use, and

periodically inspecting the products for adjustment, wear, and damage.

• If you do not understand all of the instructions and cautions, or if you have no mechanical experience and are not

thoroughly familiar with the installation procedures, you should have the product installed by a professional installer

such as a roof rack specialist.

Tools Required

• 13 mm Spanner

• Screwdriver (optional)

Installing Gas Bottle Restraint on to a Heavy Duty Cargo Tray

Go to Page 2

Installing Gas Bottle Restraint on to a Cargo Basket on Prorack Heavy Duty, Trade and

other Heavy Duty Crossbars

Go to Page 3

Installing Gas Bottle Restraint on to a Cargo Basket on Prorack Aero and International

T-Slot Crossbars

Go to Page 4

Contents

Kit Contents

Item Component Qty

1 Gas Bottle Restraint Strap 1

2 Ratchet Strap 1

3 M10 Eye Bolt 2

4 M10 Washer 4

5 M10 Square Nut 2

6 M10 Spring Nut 2

7 M8 Set Screw 2

8 M8 Spring Washer 2

9 M8 Washer 2

10 Restraint Clamp with Bump On 2

11 Restraint Mount 1

12 M8 Channel Nut 2

Page 2 of 5

09-13-569-Rev2

Position the Restraint Mount underneath the chosen inner tray slat.

Line up the M8 Channel Nut on the underside channel of the Restraint Mount with the smaller inboard hole.

Installation For Heavy Duty Cargo Trays

Important! Fit to a centrally located inner slat, not to outer slats.

Install Restraint Clamp onto outside ridge of the chosen inner tray slat and secure to Restraint Mount with

M8 Washer, M8 Spring Washer and M8 Set Screw. Use a 13 mm spanner to tighten screws to 14 Nm.

Repeat all steps for other side.

M8 Washer

M8 Spring Washer

M8 Set Screw

Restraint Clamp

M8 Channel Nut

Place the Restraint Strap over the top of the 4 kg Gas Bottle and attach the hooked end to an outboard slot

in the Restraint Mount. Feed the unhooked end of the Restraint Strap through the Ratchet. Attach the

Ratchet Strap hook to the other outboard slot in the Restraint Mount.

Tighten Ratchet until gas bottle is ﬁrmly secured.

Page 3 of 5

09-13-569-Rev2

3Fasten an M10 Eye Bolt and an M10 Washer

onto each M10 Spring Nut. Tighten Eye Bolts.

A tool such as a screwdriver through the eye

of the bolt may be used for leverage to tighten

the Eye Bolt ﬁrmly.

Insert two M10 Spring Nuts into the crossbar

channel on either side of the gas bottle. It is

recommended that the distance between the

two Spring Nuts measure roughly 400 mm.

Push Spring Nuts down into the crossbar

channel and twist to lock into place.

400 mm

The preferred orientation of Eye

Bolts is perpendicular to crossbar

4Place the Restraint Strap over the top of the

4 kg Gas Bottle and attach the hooked end to

an Eye Bolt. Feed the unhooked end of the

Restraint Strap through the Ratchet. Attach

the Ratchet Strap hook to the other Eye Bolt.

Tighten Ratchet until gas bottle is ﬁrmly

secured.

Load the 4 kg gas bottle onto the

basket and centered over a crossbar.

Installation for Baskets on Prorack Heavy Duty, Trade and other Heavy Duty Crossbars

Page 4 of 5

09-13-569-Rev2

3Fasten an M10 Eye Bolt and two M10 Washers

onto each M10 Square Nut. Tighten Eye Bolts.

A tool such as a screwdriver through the eye of

the bolt may be used for leverage to tighten the

Eye Bolt ﬁrmly.

1Load the 4 kg gas bottle onto the

basket and centered over a crossbar.

Installation for Baskets on Prorack Aero and International T-Slot Crossbars

2Remove leg cover or end cap. Push rubber

inﬁll down and slide two M10 Square Nuts

into the crossbar channel on either side

of the gas bottle. It is recommended that

the distance between the two Square Nuts

measure roughly 400 mm. Replace leg cover

or end cap.

400 mm

4Place the Restraint Strap over the top of the

4 kg Gas Bottle and attach the hooked end to

an Eye Bolt. Feed the unhooked end of the

Restraint Strap through the Ratchet. Attach

the Ratchet Strap hook to the other Eye Bolt.

Tighten Ratchet until gas bottle is ﬁrmly

secured.

The preferred orientation of Eye

Bolts is perpendicular to crossbar

Page 5 of 5

09-13-569-Rev2

Caution

• Ensure that all loads are distributed evenly across the roof racks and are fastened securely.

• A loaded roof rack system can alter the performance of your vehicle. Be especially aware of the effects of side winds,

changing of direction, and braking performance. Avoid rapid acceleration and deceleration. Drive Carefully.

• Make sure all loads are securely fastened with non-elastic straps. Check regularly during longer journeys.

• Never drive into a car wash with the roof rack system ﬁtted.

• Do not exceed the vehicle manufacturer’s roof load rating. Total load equals weight of roof racks + accessories + cargo/

equipment.

• Ratcheting strap must not be used for lifting. Protect from abrasion and friction. Do not tie knots in the straps. Do not

use a damaged strap.

• 150 kg lashing capacity on the polypropylene webbing.

Prorack

17 Hinkler Court, Brendale

QLD 4500, Australia

Freephone www.prorack.co.za

AU: 1800 143 548 www.prorack.com.au

NZ: 0800 4776 722 www.prorack.co.nz

Maintenance

• Check accessory is securely attached whenever you reﬁt it to the vehicle. If the unit feels loose, refer to the ﬁtting

instructions and readjust.

• Regularly check all fasteners. This includes all attached accessories and roof racks.

• If straps become contaminated with oil, fuel or acid remove with hot soapy water.

• If the ratchet mechanism becomes stiff in use, a small amount of lubrication applied to the moving parts will ease

operation.

Andere Prorack Autozubehör Handbücher

Prorack

Prorack K569 Bedienungsanleitung

Prorack

Prorack K639 Bedienungsanleitung

Prorack

Prorack K101 Bedienungsanleitung

Prorack

Prorack K512 Bedienungsanleitung

Prorack

Prorack K138 Bedienungsanleitung

Prorack

Prorack K426 Bedienungsanleitung

Prorack

Prorack K174 Bedienungsanleitung

Prorack

Prorack K431 Bedienungsanleitung

Prorack

Prorack K319 Bedienungsanleitung

Prorack

Prorack K715 Bedienungsanleitung

Prorack

Prorack K982 Bedienungs- und Installationshandbuch

Prorack

Prorack K449 Bedienungsanleitung

Prorack

Prorack K157 Bedienungsanleitung

Prorack

Prorack K694 Bedienungsanleitung

Prorack

Prorack K611 Bedienungsanleitung

Prorack

Prorack K427 Bedienungsanleitung

Prorack

Prorack K072 Bedienungsanleitung

Prorack

Prorack K162 Bedienungsanleitung

Prorack

Prorack K474 Bedienungsanleitung

Prorack

Prorack K751 Bedienungsanleitung

Prorack

Prorack K820 Bedienungsanleitung

Prorack

Prorack K322 Bedienungs- und Installationshandbuch

Prorack

Prorack K624 Bedienungs- und Installationshandbuch

Prorack

Prorack K462 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung