Pullman Holt E1200 Installationsanleitung

Save For Future Reference

Portable Tank Extractor

Model E1200

Operation & Care Instructions

This extractor is a high quality, precision made product. All parts used in the manufac-

turingofthisextractorhave passed rigid quality control standards prior to assembly,and

an "each unit" final inspection prior to packaging is your assurance of proper assembly.

This extractor was protectively packed to prevent possible damage in transit. Should

damage occur,please notify the transporting carrier immediately for loss and/or claim.

IMPORTANT SAFEGUARDS

Make sure the machine is plugged into an electrical outlet with the

same voltage as shown on the switch plate of the machine. It is

important to have the machine properly energized.

Disconnect power cord from the outlet before attempting mainte-

nance or repair work. Do not leave machine connected to an elec-

trical outlet when unattended.

Do not operate machine in standing water. Such use can cause

electric shock.

Do not use volatile substances such as gasoline, kerosene, etc.in

the machine or anywhere near the cleaning area. The use or pres-

ence of such materials could cause an explosion and fire.

If an extension cord is necessary, use a three conductor grounded

cord, 12 gauge wire or heavier to prevent motor burnout and over-

heating of wire.

To avoid electric shock, do not expose to rain - store indoors.

Do not use the machine for dry vacuuming. The machine is not fit-

ted with a fine dust filter. To use machine for dry vacuuming,request

more information on a dry vacuum attachment.

Always use ball float filter (reusable vacuum filter) to protect vacuum

motors.

In case of overfoaming, use defoamer in recovery tank to prevent

damage to the vacuum motors.

Use only recommended carpet cleaning solutions and defoamer

intended for machines of this type. Do not use dyes, bleaches,

ammonia, or other additives. The use of powdered cleaning com-

pounds, if not diluted or dissolved properly may damage the pump.

Do not expose machine to freezing temperatures, it could be dam-

aged.

Only authorized repair shop or dealer should attempt repairs on any

machine.

Do not use unauthorized replacement parts. Proper performance of

the machine could be affected if substitutes are used.

WARNING

The machine is designed for use on carpet, floor and upholstery

extraction applications as per instruction and recommendations

written in this manual. Any deviation from its proper use or pur-

pose and the consequential damage that may occur is the sole

responsibility of the end user.

Use defoamer in recovery tank to prevent damage to vacuum

motors.

Make sure the drain valve and recovery tank lid are closed before

turning on vacuum and pump motor switches.

4. To clean,pull the wand over the carpet with solution control valve

lever pressed. Press solution control valve lever only during pull

strokes. (Fig. 6)

Release the solution control valve lever and pass the wand over

the dampened area once or twice with either a pull or push

stroke, or both. Repeat the process until the liquid does not

appear to be passing through the wand.

NOTE: The weight of the wand and the vacuum suction are suf-

ficient to obtain satisfactory results. Additional physical pressure

is unnecessary.

Continue cleaning until the clean water tank is empty and/or

recovery tank is full. Turn off all switches and empty the recov-

ery tank. The vacuum suction will be reduced if the recovery

tank is full.

5. After recovery tank is drained, repeat steps 3 & 4.

LAST STEP:

Turn off pump switch but leave the vacuum switch (s) on.

Disconnect the vacuum hose and solution hose from the wand.

Insertthe vacuumhose into the cleanwater tankand vacuum out the

excess water. (Fig.7) Drain and thoroughly clean the recovery tank.

Make sure the ball float cage and vacuum filter have been rinsed

thoroughly while it’s still wet.

Remove dirt and lint build-up inside the recovery tank, rinse with

running water. Make sure debris does not become lodged in

between the rubber gaskets on the drain valve.

Pump clean water through pump to protect unit from freezing.

Wrap power cord around cord-winder or handle.

Check for any loose parts on the machine, if loose, tighten them.

Never use solution tank as storage, machine can be damaged.

Operating Procedures

FIRST STEP:

Always thoroughly vacuum the surface to be steam-cleaned.

MACHINE ASSEMBLY:

1. Connect vacuum hose to vacuum intake (#1) on the machine and

to the wand (#3). Connect solution hose to the water output

(solution hose connector) (#2) on the machine (Fig. 1) and to the

quick connector on the wand (#4). (Fig. 2)

2. To reduce the possibility of electric shock,the machine is factory

equipped with an approved three conductor cord and grounding

plug. This plug is to be used only with proper grounding type

(three prong) receptacles. (Fig. 4)

An adapter is available for connecting three prong type plugs to

two prong receptacles. (Fig. 5) The green rigid lug extending

from the adapter must be connected to a permanent grounding

suchas properly grounded outlet box. Do not break off orpull out

the grounding blade.

OPERATION:

3. Method A

Pre-spray the carpet with carpet cleaning solution.

Fill open tank (solution tank) with clean hot water (140 F. max.)

(Fig.1) (exception: use cool water for wool carpets)

Method B

Fill open tank (solution tank) with clean hot water. Add 2 or 4

ounces of carpet cleaner per gallon of water or as needed.

IMPORTANT: Make sure ball float filter (vacuum filter) is clean

and in place at all times.

Use only recommended carpet cleaning solution intended for

machines of this type. Do not use solvents, bleaches, ammonia,

or other additives which can damage the machine and the car-

pet.

Symptom Possible Cause(s) Corrective Action

ELECTRICAL SYSTEM

No electrical power 1) Check the outlet & the plug 1) Plug in properly

2) Damaged cord 2) See authorized service center

3) Circuit breaker off or fuse blown 3) Turn circuit breaker on or replace fuse. Unplug any equipment using

the same circuit.

Switch is turned on, power 1) Faulty electrical cable 1) See authorized service center

is intermittent to all motors 2) Defective switch 2) See authorized service center

3) Loose terminal or corroded connector 3) See authorized service center

Electrical shock 1) Equipment not grounded 1) Check outlet for proper grounding. See authorized service center

VACUUM SYSTEM

Vacuum motor on,little or 1) Lid is not closed 1) Close the lid

no vacuum on suction 2) Drain valve not closed 2) Push drain valve handle down

head (wand) or upholstery 3) Hose or wand clogged 3) Clean

tool. 4) Accumulated dirt on the ball float cage 4) Clean or replace the filter

and filter

5) Worn out lid gasket 5) Replace the gasket

6) Lint and dirt build-up in wand 6) Clean the wand

7) Damaged vacuum hose 7) Replace

8) Loose or no vacuum hose connection 8) See authorized service center

inside the machine

9) Lint accumulation in vacuum fans 9) See authorized service center

Vacuum motor runs intermittently 1) See authorized service center

PUMP SYSTEM

Pump motor stopped 1) Pressure built up 1) Release pressure by opening up (press the lever on the wand)

2) Thermal overload (overheated) 2) Turn off the switch and wait for the pump to cool down.

3) Damaged motor or rectifier 3) See authorized service center

4) Pump switch defective 4) See authorized service center

5) Loose wire connection 5) See authorized service center

6) Pump pressure switch defective 6) See authorized service center

7) Faulty motor 7) See authorized service center

Loss of pump pressure 1) Clogged or dirty spray-tip 1) Clean

with wand valve open, 2) Accumulated dirt in solution line 2) Clean

and/or uneven or weak 3) Dirty or plugged filter screen 3) Remove and clean or replace

spray from the spray jet 4) Pump check valve worn or dirty 4) See authorized service center

tip 5) Malfunction in the wand valve 5) See authorized service center

6) Hose quick connect bad or clogged 6) See authorized service center

with lint

OTHER PROBLEMS

No water from the jet 1) Machine not plugged in (or circuit 1) Plug into proper sized outlet

breaker blown)

2) Switch is not on 2) Turn the switch on

3) Empty solution tank 3) Fill the solution tank with water

4) The hose (s) not connected properly 4) Connect hose (s) properly (see pump problem section)

Water or foam coming 1) Over foaming of water in recovery tank 1) Put defoamer in the recovery tank or put it in the vacuum hose with

out of the exhaust vac motor running

2) Elbow fitting in recovery tank pointing 2) Point the elbow away from ball-float cage

toward the ball-float cage

3) No ball-float cage 3) Install ball-float cage w/ filter

4) Too much water in the recovery tank 4) Drain the recovery tank

WARNING : Always disconnect power cable from electrical outlet when working on this machine.

DO NOT ATTEMPT TO REPAIR THE MACHINE. CONSULT AN AUTHORIZED PULLMAN-HOLT SERVICE CENTER.

TROUBLE SHOOTING GUIDE

10702 N 46th Street •Tampa, FL 33617

(813)971-2223 •toll free (800) 237-7582

fax (813) 971-6090 •order entry fax (800) 833-8875

www.pullmanholtcorp. com B703603 1/04

Inhaltsverzeichnis

Andere Pullman Holt Staubsauger Handbücher

Pullman Holt

Pullman Holt 86ASB54C Bedienungsanleitung

Pullman Holt

Pullman Holt EVACII-20 Bedienungsanleitung

Pullman Holt

Pullman Holt 45 Installationsanleitung

Pullman Holt

Pullman Holt 45-10P Anwendungshandbuch

Pullman Holt

Pullman Holt 30ASB Installationsanleitung

Pullman Holt

Pullman Holt 25 Bedienungsanleitung

Pullman Holt

Pullman Holt UV10 Bedienungsanleitung

Pullman Holt

Pullman Holt 45-20P POV Installationsanleitung

Pullman Holt

Pullman Holt UV9 Installationsanleitung

Pullman Holt

Pullman Holt P5 PorterVac Installationsanleitung

Pullman Holt

Pullman Holt 102 12P Installationsanleitung

Pullman Holt

Pullman Holt 45HEPA-D Installationsanleitung

Pullman Holt

Pullman Holt P7 Porter Vac Backpack Vacuum/Blower Installationsanleitung

Pullman Holt

Pullman Holt U10 Installationsanleitung

Pullman Holt

Pullman Holt 102ASB Bedienungsanleitung

Pullman Holt

Pullman Holt 102 Installationsanleitung

Pullman Holt

Pullman Holt 102ASB-12PD Installationsanleitung

Pullman Holt

Pullman Holt 45 Installationsanleitung

Pullman Holt

Pullman Holt 86ASB-5D4C Installationsanleitung

Pullman Holt

Pullman Holt Big Red Drum Installationsanleitung

Pullman Holt

Pullman Holt P7 Porter Vac Backpack Anwendungshandbuch

Pullman Holt

Pullman Holt 86ASB5D4C Bedienungsanleitung

Pullman Holt

Pullman Holt 390CV Installationsanleitung

Pullman Holt

Pullman Holt Rug Boss E1300 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung