Q-See QSDF8204C4 Bedienungsanleitung
Quick Start Guide
1Set Up 2Connect 3Enjoy
Quick Start Guide – Remote Internet Monitoring
4 Channel DVR with 7” In-Dash LCD and 4 Color CCD Cameras
Model: QSDF8204C4
Remote Internet Monitoring
AVVOL+
OPEN
AUTOMOBILE TV SYSTEM
VOL-
CH+
VIDEO CD SET
1/ 2/abc
6/mno7/qrs 8/tuv9/wxyz INFO/10+/
PTZ/ /
3/def 4/ghi 5/jkl
HOUR MIN
CH-
TV
CLOCK
[
MENU/+ Focus Zoom Iris Speed AESC
STOPFFREWPLAYSEARCHRec
Power HDD Backup NetPlay REC
DVR with 7” In-Dash LCD, Pre-Installed Hard Drive
1Set Up
Accessing the DVR from a single router: To access the DVR from a computer that is
using the same router as the DVR, set up the network settings using either the DHCP
option or assigning a static IP address:
To Setup DHCP (Most common routers are DHCP)
Convert assigned DHCP IP address to
a Static IP Address: (Do this so your IP
address does not change.) Push the INFO
button on the remote or DVR front panel to
get the IP address information assigned by
the router. Then go back to the IP cong
window change to static, and enter the IP
addresses from the info screen.
ARemote Monitoring Set Up for DVR using DHCP to setup IP address
3. Under IP Cong:
select DHCP, select OK
and reboot the system for
settings to register. Push the
INFO
button on
the remote
control to
see the
newly
assigned IP
address.
1. To assign an IP address to
the DVR using DHCP, select
the Menu Key on the DVR to
access the Main Menu.
2. Use the DVR Direction Keys
to select the Network Option
(red box) and push Enter Key.
Select the IP Conguration
option (green box) and select
Enter.
Page 1
Setup the network conguration on the DVR to work with the settings on the router.
Static IP: To obtain the router settings, go to the Run Option on a computer that is attached
to the same router as the DVR and type “cmd”. Select OK to bring up the command
prompt screen, as shown in the picture below. Type “ipcong” at the prompt to access
the router settings. Capture the Gateway and Subnet Mask Numbers (see green arrows
below). On the DVR push the Menu Key to prompt the Main Menu, use the Direction Keys
to select the Network option and push Enter to display the Network Screen. Select the IP
Cong option and select Enter to display the IP Cong Window.
To set the IP address of the DVR use the same rst three sets of numbers as the Gateway
and assign a fourth set of numbers that is different from all other devices attached to the
same router. For example: if the IP address of your computer in the ipcong was a single or
two digit number, use a number in the 100s, if in the 100s, use 200.
Page 2
BRemote Monitoring Set Up for DVR using a Static IP address
PPPOE: Select the PPPOE option in the IP cong options. To access the IP cong
window: Push the Menu Key on the DVR to prompt the Main Menu. Use the Direction
Keys to select the Network option and push Enter to display the Network Screen, select the
IP Cong option and select Enter to display the IP Cong Window.
CAttaching the DVR directly to DSL/Cable modem
1. Use the Enter key to change the IP cong setting to PPPOE
2. Enter user id and password in the PPPOE section
*Contact your Internet Service Provider for your user id and password
Page 3
1. Use the Enter key to change the IP cong setting to PPPOE
2. Enter user id and password in the PPPOE section
*Contact your Internet Service Provider for your user id and password
2Connect
APort Forwarding
To access the DVR from a remote computer over the internet via internet browser
(Internet Explorer).
1Forward Port 80 and Port 2000 on the router attached to the DVR, to the IP address
of the DVR. *If you can’t use HTTP Port 80 or 2000 due to use or your Internet
Service Provider, use a different port in the same range. When selecting a different
port, forward the IP address of the router to the new port and change the settings in
the DVR Network settings. You will also need to add the new port to the end of the IP
address in the browser window. For example, if you use port 83, you add :83 to the
end of the IP address.
2For instructions on the most
popular routers go to
www.portforward.com
Click on the orange “Routers”
link in the second paragraph,
select your router from the
list of router manufacturers,
brand and model.
3Click on the orange “Default
Guide” link to view port
forwarding instructions for
your router.
4Enter the public IP address of
the router the DVR is attached
to. You can get this by going
to www.myipaddress.com on
a computer that is attached to
the same router as the DVR.
For additional help with forwarding ports on your router, please visit :
www.portforward.com/qsee
Page 4
BAccessing the DVR through a static or dynamic IP address
*Dynamic IP address can change from time to time depending on your Internet
Service Provider.
CAccessing the DVR through Internet Explorer Browser (IE):
Modify internet browser controls.
1 If the Dynamic IP address changes, you can nd the new IP address by going to
www.myipaddress.com on a computer that is attached to the same router as the
DVR.
2Two options:
a) Get a static IP address from your Internet Service Provider.
b) Use a dynamic domain name instead of IP address.
3Dynamic domain name: Go to www.no-ip.com or www.dyndns.com Register and
download the free web software on a computer that is connected to the same router
as the DVR. Run the software and follow the on screen prompts to install.
Enable the “Pop Up Blocker” option: go to the Internet Explorer Tool Bar, select
Tools, select the “Pop Up Blocker” from the drop down and select “Turn Off
Pop Up Blocker”.
Page 5
If you get an error message
“Program Cannot Load” or
because it cannot be veried, then
click on the “Advanced” tab on the
top right. It will display a window.
Scroll down to “Security”, click on
the options “Allow Software to Run
or Install Even If the Signature is
Invalid” and “Allow Active Content
to Run Files on My Computer”.
Trouble Shooting Connecting:
*Anti-virus programs, re walls, and other plug ins could be blocking the Active X Control.
Close them and try to connect. For more advanced instructions or for trouble-shooting,
please consult the Q-SEE QSDF8204 User Manual which came with your unit.
Or download the manual from our support section at www.Q-See.com
Enable the Active X Controls,
go back up to the Tool Bar, and
select Tools. Select from the
drop down “Internet Options”
(green arrow), prompting a new
display window, shown on the
right.
Go to “Security” (red box), click on “Custom
Level” (green box), click “OK”. New page
opens, scroll down to Active X Controls
and Plug Ins and set all to “Prompt” or
“Enabled”.
Page 6
Digital Peripheral Solutions, Inc.
8015 East Crystal Drive,
Anaheim, CA 92807
www.Q-See.com
3Enjoy
Congratulations! You have just completed the
Quick Start Guide for Remote Internet Monitoring.
If you require further assistance after reading the User Manual,
please contact Technical Support:
On the Web: (24/7) Visit the Technical Support Section
www.Q-See.com
By Phone: (Monday thru Friday, 9am-5pm (PST)
1 (877) 998 3440, ext 539
By Email:
For more information about Q-See Products, please contact customer service:
1 (877) 998 3440, ext 538 (Monday thru Friday, 9am-5pm)
or view our selection online at www.Q-See.com
Q-See is a registered trademark of Digital Peripheral Solutions, Inc.
Inhaltsverzeichnis
Andere Q-See DVR Handbücher
Q-See
Q-See H.264 NETWORK DVR Bedienungsanleitung
Q-See
Q-See QC804 Bedienungsanleitung
Q-See
Q-See QSD6204 Bedienungsanleitung
Q-See
Q-See QC-SERIES Bedienungsanleitung
Q-See
Q-See QS434 Bedienungsanleitung
Q-See
Q-See QSTD501616C Bedienungsanleitung
Q-See
Q-See QSD42908C8 Bedienungsanleitung
Q-See
Q-See QSD42908 Net Bedienungsanleitung
Q-See
Q-See QSD6209C9--250 Bedienungsanleitung
Q-See
Q-See QSDR74RTS Bedienungsanleitung
Q-See
Q-See QSDR74RTS Bedienungsanleitung
Q-See
Q-See QR4714 Bedienungsanleitung
Q-See
Q-See QSD2316L Benutzerhandbuch
Q-See
Q-See QT SERIES Bedienungsanleitung
Q-See
Q-See QC3016-12E4-1 Bedienungsanleitung
Q-See
Q-See QC-SERIES Bedienungsanleitung
Q-See
Q-See QC40108 Bedienungsanleitung
Q-See
Q-See QT426 Bedienungsanleitung
Q-See
Q-See Prosumer QT528 Bedienungsanleitung
Q-See
Q-See QSD9004V Bedienungsanleitung
